Search Results

There are benefits of using ultra thin wall (UTW) substrates (i.e., 900/2, 400/4, etc) in lowering cost and emission level. However, the more fragile mechanical characteristics of the UTW present a challenge to design and manufacture of robust catalytic converters. This paper describes a method of canning trial, where a combined Design of Experiment / Monte-Carlo analysis method was used, to develop and validate a canning method for ultra thin wall substrates. Canning trials were conducted in two stages-- Prototype Canning Trial and Production Canning Trial. In Prototype Canning Trial, the root cause of substrate failure was identified and a model for predicting substrate failure was established. Key factors affecting scrap rate and gap capability were identified and predictions were performed on scrap rate and gap capability with the allowed variations in the key factors. The results provided guidelines in designing production line and process control.

Not all software tools are created equal and not all software tools are created to perform the same tasks. Therefore, different software tools are used to perform different tasks. However, being able to share the information between the different software tools, without having to manually re-enter (duplicate) any of the information, can save a lot of time and improve the quality of the product. The control software interface presented in this paper, allows system engineers to exchange data between software tools in an efficient manner which maximizes each tools capabilities and ultimately reduces development time and improves the quality of the product.

The work presented here outlines the development of a robust CAO tool for optimal design of electromagnetic retarder machines. The developed EM-CAO tool is then used to perform a wide variety of CAE/CAO tasks, from automatically computing the torque versus rpm performance curves of the EM retarder to performing optimization. Two specific examples of optimal design of the EM retarder are reported. Through the use of a task manager/optimizer repetitive jobs are fully automated thereby making the analysis and optimization of electromagnetic retarders faster and user-friendlier.

Traditionally fog lamps use halogen filament light sources. With the emergence of high brightness white LEDs, it is now possible to develop automotive forward lighting systems with LED light sources. Six LEDs are shown to be sufficient for the implementation of a European fog lamp using a faceted reflector optical approach. Each reflector together with the LED light source forms a modular element. The optical parameters of two different lamp designs are compared and correlation between the simulation and prototype measurements is shown. Further, additional forward lighting functions can be implemented through the use of additional elements.

Manual ‘porting” of source code is often required in order to “reuse” control software in different applications with different target hardware. This process is not cost effective. Maintaining multiple “versions” of the same software also causes problems. This paper describes a way in which multiple target source code can be generated from a single model. A custom data class is developed so that it can be used to define both signal and parameter data types necessary for data dictionary-driven models. This capability allows a single model to be used to generate code for multiple target hardware architectures. A software development process using a generic model to support multiple hardware targets is compared with the hand porting process (e.g. floating-point to/from fixed-point). Auto code generation from a sample multi-target feature model will be presented. The efficiency of the auto code will also be discussed.

The purpose of this paper is to demonstrate our success in taking advantage of model-based development tools and auto-code technology to accelerate the typical life cycle development of powertrain software. In particular, we applied the technology as a clean sheet approach to Visteon's third generation Electronic Throttle Control system. In the process of applying model-based development and 100% auto-code, we identified various pitfalls and created solutions to overcome the gap between technology and development process during each phase of the entire software development life cycle. We will share our lessons learned during the requirement, design, implementation, and validation stages.

A twenty-five kilowatt (peak power for one minute), permanent magnet electric machine for a hybrid electric vehicle application was designed and tested. The electric machine is located in the clutch housing of an automatically shifted manual transmission and is subjected to 120 °C continuous ambient temperatures. The package constraints and duty cycle requirements resulted in an extremely challenging thermal design for an electric machine. The losses in the machine were predicted using models based on first principles and the heat transfer in the machine was modeled using computational fluid dynamics. The simulations were compared to test results over a variety of operating conditions and the results were used to validate the models. Parametric studies were conducted to evaluate the performance of potting materials and cooling topologies.

This paper describes two electronic throttle controllers of Visteon Corporation with one already in production and the other currently under development. Analysis and tuning of the two controllers are described. The general structure of the controllers consists of a reference shaping subsystem and a proportional-plus-integral-plus-derivative(PID) controller supplemented with additional terms that deal with the nonlinearility of the electronic throttle body. Due to a friction cancellation term in the controller that minimizes the nonlinearity of the system, linear system analysis techniques are applied. The transfer functions of the electronic throttle body at six different operating conditions are derived. Analysis of the closed-loop dynamics is performed based on the plant and the controller transfer-functions. Controller fine-tuning is performed using frequency response techniques, MATLAB simulations and testing on the actual system.

The increasing power requirement for automotive electronics (radios, etc.), combined with ever-shrinking size and weight allowances, is creating a greater need for optimization and robust design of heat sinks. Not only does a heat sink directly affect the overall performance and reliability of a specific electronics application, but a well-designed, optimized heat sink can have other benefits - such as eliminating the requirement for special fans, reducing weight of the application, eliminating additional heat sink support structures, etc. Optimizing heat sink efficiency and thermal performance offers a challenge, due to the many competing design requirements. These requirements include effecting greater temperature reductions, accommodating vehicle packaging requirements and size limitations, generating a uniform heat distribution, etc., and all the while reducing the heat sink cost.

In the absence of prototypes, analytical methods such as finite element analysis are very useful in resolving noise and vibration problems, by predicting dynamic behavior of the automotive components and systems. Finite Element Analysis (FEA) is a simulation technique and involves making assumptions that affect analytical results. Acceptance and use of these results is greatly enhanced through test validation. In this paper, dynamic behavior of the automotive propshaft equipped with cardboard liner and torsional damper is investigated. The finite element model is validated at both component and subsystem levels using frequency response functions. Effects of the cardboard liner and torsional damper on the propshaft bending, torsional and breathing frequencies are studied under free-free boundary conditions. Effects of the U-Joint stiffness along with other design variables on the driveshaft dynamic behavior are also studied.

The fundamentals of multi-leaf spring design as determined through beam theory offers a general perspective on how finite element analysis works. Additionally, the fundamentals of combining dissimilar materials require a basic knowledge of how the combined equivalent modulus affects the overall stiffness characteristics of multi-leaf design. By capturing these basic fundamentals into finite element modeling, an analysis of a steel-composite multi-leaf contact model relative to an idealized steel-composite multi-leaf model shows the importance of contact modeling. The results demonstrate the important differences between an idealized non-contact model relative to a complete contact model.

The starter drive clutch is a one way roller clutch and a key component in a starter motor that is used to crank internal combustion engines. The starter drive clutch transmits torque from an electrical motor to a ring gear mounted on a cranking shaft in an engine thus cranks the engine. The clutch also prevents the whole starter from damage caused by extremely high load and/or extremely high speed applied to the starter pinion from the engine. Drive slippage and barrel cracking are two major failure modes for the starter drive[1]. Insufficient torque capacity results in drive slippage while excessive high hoop stress on the clutch barrel ring causes barrel crack. To eliminate drive slippage failure, the clutch should be designed with high torque capacity. High torque capacity, however, is a cause of high hoop stress on the barrel that may result in the cracked barrel failure. Higher torque capacity and lower hoop stress are two completely opposite design directions.

This paper discusses our experiences on the implementation and benefits of using the Hardware-In-the-Loop (HIL) systems for Powertrain control system software verification and validation. The Visteon HIL system integrated with several off-the-shelf diagnostics and calibration tools is briefly explained. Further, discussions on test automation sequence control and failure insertion are outlined The capabilities and advantages of using HIL for unit level software testing, open loop and closed-loop system testing, fault insertion and test automation are described. HIL also facilitates Software and Hardware Interface validation testing with low-level driver and platform software. This paper attempts to show the experiences with and capabilities of these HIL systems.

There are many opportunities in a current automotive HVAC case for improved performance, and cost savings. Based on these opportunities, a new HVAC case design has been developed. This new design is smaller and lighter than current cases while meeting many of the performance requirements. The case also features a unique plenum design for air distribution to the three modes, panel, floor, and defrost. The results of simulation and laboratory testing confirmed the concept of the new HVAC design.

As powertrains continue to get more efficient, less waste heat is available for warming the passenger compartment. Although several supplemental heating devices are currently on the market, including electric heaters, viscous heaters, and fuel operated heaters, they each have shortcomings related to cost, capacity, efficiency, and/or environmental concerns[1]. In an attempt to provide superior time-to-comfort in a cost, weight, package efficient, and environmentally friendly manner, an R134a heat pump (HP) system was developed. Several technical issues were overcome while developing this system. Production vehicles have been retrofitted to incorporate the R134a heat pump system and tested in a climatic wind tunnel. Test results for a -18°C warm-up test were compared to baseline data, showing significant improvements in average discharge air and breath level temperatures.

Stabilizer bars in a suspension system are supported with bushings by a frame structure. To prevent the axial movement of the stabilizer bar within the bushing, several new stabilizer bar-bushing systems have been developed. The new systems introduce permanent compressive force between the bar and the bushing thereby preventing the relative movement of the bar within the bushing. This mechanical bond between the bar and the bushing can eliminate features such as grippy flats, collars etc. In addition, by controlling the compression parameters, the properties of the bushing such as bushing rates can be tuned and hence can be used to improve the ride and handling performance of the vehicle. In this paper, nonlinear CAE tools are used to evaluate one such compressively loaded bushing system. Computational difficulties associated with modeling such a system are discussed.

Customer clinics and surveys have revealed the increased importance to the customer of good defrost and demist performance in their vehicle. Achieving this level of performance, within the time and cost constraints of a modern vehicle development program, places increased reliance on computational (CAE) techniques. However, this paper describes how the optimum development process should be to combine this reliance upon CAE methods with a newly developed experimental technique. This new laser Doppler velocimetry (LDV) based methodology is employed at all stages of the development process and complements the CAE techniques perfectly. The end result is optimized airflow management within the vehicle cabin – essential if good defrost and demist performance is to be achieved in a vehicle.

Interior compartment doors are required by Federal Motor Vehicle Safety Standard (FMVSS) 201, to stay closed during physical head impact testing, and when subjected to specific inertia loads. This paper defines interior compartment doors, and shows examples of several different latches designed to keep these doors closed. It also explores the details of the requirements that interior compartment doors and their latches must meet, including differing requirements from automobile manufacturers. It then shows the conventional static method a supplier uses to analyze a latch and door system. And, since static calculations can't always capture the complexities of a dynamic event, this paper also presents a case study of one particular latch and door system showing a way to simulate the forces experienced by a latch. The dynamic simulation is done using Finite Element Analysis and instrumentation of actual hardware in physical tests.

Visteon has developed a CAE procedure to qualify instrument panel (IP) products under the vehicle key life test environments, by employing a set of CAE simulation and durability techniques. The virtual key life test method simulates the same structural configuration and the proving ground road loads as in the physical test. A representative dynamic road load profile model is constructed based on the vehicle proving ground field data. The dynamic stress simulation is realized by employing the finite element transient analysis. The durability evaluation is based on the dynamic stress results and the material fatigue properties of each component. The procedure has helped the IP engineering team to identify and correct potential durability problems at earlier design stage without a prototype. It has shown that the CAE virtual key life test procedure provides a way to speed up IP product development, to minimize prototypes and costs.

Past and current practice in this industry for measuring individual loudspeaker drive units has included great freedom in choice of chamber type and baffling. Many of these methods do not yield the true acoustical response of the loudspeaker free from acoustical artifacts. In fact, international loudspeaker measurement standards and many carmaker specifications allow test set-ups that significantly mask the true response of the loudspeaker. This paper is intended to drive awareness of this issue in the industry in an effort to promote a new standard for measurement.