Criteria

Text:
Display:

Results

Viewing 1 to 30 of 3456
2015-03-04
WIP Standard
AMS4824E
This specification covers bearings of a leaded bronze cast on one or both faces of a steel backing with a layer of babbitt metal cast on the leaded bronze.
2015-03-03
WIP Standard
AMSQQA200/8A
This specification covers the specific requirements for aluminum alloy 6061 bar, rod, shapes, tube, and wire produced by extrusion.
2015-02-27
Standard
AMS4323C
This specification covers an aluminum alloy in the form of hand forgings up to 6 inches (152 mm) inclusive, in nominal as-forged thickness and having a cross-sectional area of not more than 156 square inches (1006 cm2).
2015-02-25
Standard
AMS4634C
This specification covers an aluminum bronze alloy in the form of bars, rods, forgings, and forging stock.
2015-02-17
WIP Standard
AMS2355L
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable specification requirements of wrought aluminum alloy and wrought magnesium alloy mill products (except forging stock), and includes quality assurance and testing procedures for rolled, forged, and flash welded rings (See 8.3). Requirements are specified in inch/pound units.
2015-02-17
Standard
AMS4720G
This specification covers one type of bronze in the form of round wire 0.500 inch (12.70 mm) and under in nominal diameter.This specification covers one type of bronze in the form of round wire 0.500 inch (12.70 mm) and under in nominal diameter.
2015-02-06
WIP Standard
D15AA
This specification is a proposed draft of a new temper (T852) which covers aluminum-lithium alloy 2050
2015-02-06
Standard
AMS4863
This specification covers a copper-nickel-tin alloy in the form of castings, made using the investment process unless sand or centrifugal processes are agreed upon by the purchaser.
2015-02-05
Standard
AMS4205D
This specification covers an aluminum alloy in the form of plate up to 5.500 inches (139.70 mm), inclusive in thickness.
2015-02-05
Standard
AMSQQA250/4B
This specification covers the specific requirements for 2024 aluminum alloy plate and sheet; the general requirements are covered in AMS-QQ-A-250.
2015-02-04
WIP Standard
AS6507
1.1 This specification is used to indicate the resistance to distortion of bare and two-side Alclad, flat sheet aluminum that will be chemically milled (often in the manufacture of aircraft skin panels). 1.2 This specification is intended for bare and two-side Alclad aluminum alloy in the T temper, which is the form of flat sheet having a thickness between 0.032 to 0.249 in. (0.8 to 6.3 mm). 1.3 Product having the capability prescribed by this specification is available in limited quantities and tempers because of the special processing required.
2015-02-03
WIP Standard
AMS2770M
This specification specifies the engineering requirements for heat treatment, by part fabricators (users) or their vendors or subcontractors, of parts (See 8.8.1). It also covers heat treatment by warehouses or distributors converting raw material from one temper to another temper (See 1.3 and 8.5). It covers the following aluminum alloys: 1100, 2004, 2014, 2017, 2024, 2098, 2117, 2124, 2219, 2224, 3003, 5052, 6013, 6061, 6063, 6066, 6951, 7049, 7050, 7075, 7149, 7178, 7249, 7475
2015-01-15
Standard
AMS4520L
This specification covers a copper alloy in the form of strip. This strip has been used typically for rolled, split bushings, but usage is not limited to such applications.
2015-01-15
Standard
AMS4090F
This specification covers an aluminum alloy in the form of plate. This plate has been used typically for structural applications requiring plate with high strength, moderate fatigue strength, and high fracture-toughness, but usage is not limited to such applications.
2015-01-07
Standard
AMS4555K
This specification covers a copper alloy (leaded brass) in the form of seamless tubing.
2015-01-05
Standard
AMS4159E
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing with a nominal diameter or least thickness (wall thickness of tubing) up to 5.000 inches, inclusive.
2015-01-05
Standard
AMS4154R
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing.
2015-01-05
Standard
AMS4479
This specification covers an aluminum alloy in the form of extruded profiles with a maximum cross-sectional area of 25 in2 (160.29 cm 2 ) and nominal thicknesses from 0.250 to 2.500 inch, inclusive (6.3 to 63.50 mm, inclusive).
2015-01-05
Standard
AMS4480
This specification covers an aluminum alloy in the form of seamless, drawn tubing.
2015-01-05
Standard
AMS4153L
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to 32 square inches (206 square cm) in area.
2015-01-05
Standard
AMS4535D
This specification covers a copper beryllium alloy in the form of mechanical tubing. This tubing has been used typically for parts requiring a combination of high strength, wear resistance, and corrosion resistance and where thermal conductivity, electrical conductivity, and low magnetic susceptibility may be important, but usage is not limited to such applications. While the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is the sole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved.
2014-12-29
Standard
AMS4037Q
This specification covers an aluminum alloy in the form of sheet and plate from 0.008 to 4.000 inches (0.20 to 101.60 mm) in thickness, inclusive (See 8.4).
2014-12-23
Standard
AMS4028H
This specification covers an aluminum alloy in the form of sheet and plate from 0.020 to 1.000 inches (0.51 to 25.4 mm) thick (See 8.3).
2014-12-23
Standard
AMS4347D
This specification covers an aluminum alloy in the form of sheet from 0.020 to 0.249 inch (0.51 to 6.32 mm), inclusive, in thickness (See 8.5).
2014-12-22
Standard
AMS4366
This specification covers an aluminum-lithium alloy in the form of extruded profiles with a maximum cross-sectional area of 19 square inches (123 cm 2 ) and a maximum circle size of 11 inches (279mm) from 0.040 to 0.499 inches (1.00 to 12.50 mm) in thickness.
2014-12-22
Standard
AMS4353
This specification covers an aluminum alloy in the form of extruded round rods. This specification covers products from 1.750 to 5.900 inches (44.45 to 150.00 mm) in diameter.
2014-12-22
Standard
AMS4113F
This specification covers an aluminum alloy in the form of extruded profiles such as angles, channels, tees, zees, I-beams, and H-beams. These products have been used typically for parts requiring moderate strength, especially where such parts require brazing or welding during fabrication, but usage is not limited to such applications.
2014-12-22
Standard
AMS4141G
This specification covers an aluminum alloy in the form of die forgings and forging stock ordered to inch/pound units. These forgings have been used typically for parts requiring good resistance to stress-corrosion cracking but with lower strength than AMS4126, but usage is not limited to such applications.
2014-12-22
Standard
AMS4050J
This specification covers an aluminum alloy in the form of plate. This plate has been used typically for parts requiring a high level of mechanical properties and good resistance to stress-corrosion cracking, but usage is not limited to such applications.
2014-12-21
WIP Standard
AMS4371B
This specification covers a magnesium alloy in the form of rolled plate. This product has been used typically for parts requiring a combination of light weight, high yield strength up to 480 °F (250 °C), relatively high corrosion resistance, and good flammability resistance for magnesium alloys,but usage is not limited to such applications.
Viewing 1 to 30 of 3456