Criteria

Text:
Display:

Results

Viewing 1 to 30 of 1048
CURRENT
2016-12-06
Standard
AMS4909K
This specification covers a titanium alloy in the form of sheet, strip, and plate up to 1.000 inch (25.40 mm) inclusive.
CURRENT
2016-12-06
Standard
AMS4962B
This specification covers a premium grade titanium alloy in the form of investment castings.
CURRENT
2016-12-06
Standard
AMST81915B
This specification prescribes the requirements for Titanium and Titanium-alloy castings produced by the investment casting process.
2016-11-18
WIP Standard
AMS4959F
This specification covers a titanium alloy in the form of cold drawn wire.
2016-10-21
WIP Standard
AMS4949B
This specification covers titanium in the form of laminated sheet. This material has been used typically for shims in which thickness is adjusted by removal of laminations as required, but usage is not limited to such applications.
2016-10-21
WIP Standard
AMS4939C
This specification covers a titanium alloy in the form of sheet, strip, and plate through 4.000 inches (101.60 mm). This material has been used typically for parts to be formed or machined in the solution heat treated condition and subsequently precipitation heat treated requiring high strength-to-weight ratio and stability up to 550 °F (288 °C) in the precipitation heat treated condition, but usage is not limited to such applications.
2016-10-21
WIP Standard
AMS4933F
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, flash welded rings, and stock for flash welded rings up through 4.000 sq. inch (25.81 cm2) cross-section.
2016-10-21
WIP Standard
AMS4917J
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2016-10-10
WIP Standard
AMS4966R
This specification covers a titanium alloy in the form of forgings and forging stock. These forgings have been used typically for parts requiring strength up to 800 °F (427 °C) and that may be welded during fabrication, but usage is not limited to such applications.
2016-10-08
WIP Standard
AMS2244D
This specification covers established manufacturing tolerances applicable to titanium and titanium alloy tubing. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of the specified range.
2016-10-08
WIP Standard
AMS4998F
This specification covers a titanium alloy in the form of prealloyed powder. This powder has been used typically for compaction into net or near net shapes and into forging stock in the form of billets or preforms, but usage is not limited to such applications.
2016-09-29
WIP Standard
AMS4915M
This specification covers a titanium alloy in the form of sheet, strip, and plate up through 4.000 inches (101.60 mm).
2016-09-29
WIP Standard
AMS4951J
This specification covers one grade of commercially pure titanium in the form of wire for welding filler metal.
2016-09-29
WIP Standard
AMS2380G
This specification covers the procedures for approval of products of premium-quality titanium alloys and the controls to be exercised in producing such products.
2016-09-29
WIP Standard
AMS4954K
This specification covers a titanium alloy in the form of wire for welding filler metal.
CURRENT
2016-09-20
Standard
AMS4970K
This specification covers a titanium alloy in the form of bars, wire, forgings up to 4.000 inches (101.60 mm) inclusive and forging stock.
CURRENT
2016-09-13
Standard
AMS4897D
This specification covers a titanium alloy in the form of sheet and strip 0.125 inch (3.18 mm) and under in nominal thickness.
CURRENT
2016-08-01
Standard
AMS4963D
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings up through 3.999 inches (101.57 mm), inclusive and stock for forging, flash welded rings, or heading.
CURRENT
2016-08-01
Standard
AS1814E
This list of terms, with accompanying photomicrographs where appropriate, is intended as a guide for use in the preparation of material specifications. The terms and photomicrographs are intended to present definitions only; they do not define either acceptance limits or minimum standards of quality. Listings are not grouped by specific alloys or conditions and represent the typical microstructures wherever they occur. Etchants used for the microstructures shown are stated. Where "Krolls" is stated, the composition is 10 ml HF, 30 ml HNO3, and 50 ml water (H2O). Other common etchants are listed in ASTM E407, Microetching Metals and Alloys.
CURRENT
2016-08-01
Standard
AMS4973H
This specification covers a titanium alloy in the form of forgings up to 4.000 inches (101.60 mm) inclusive and forging stock.
CURRENT
2016-07-11
Standard
AMS4957F
This specification covers a titanium alloy in the form of round bar and wire, 0.625 inch (15.88 mm) and under in nominal diameter or thickness.
2016-07-07
WIP Standard
G16AA
This specification covers a titanium alloy in the form of bars, wire, forgings, rings, and drawn shapes.
CURRENT
2016-07-07
Standard
AMS4921N
This specification covers one grade of commercially-pure titanium in the form of bars, wire, forgings, flash welded rings, up to 4.000 inches (101.60 mm), inclusive, in nominal diameter or least distance between parallel sides, and stock for forging or flash welded rings.
CURRENT
2016-06-16
Standard
AMS4955H
This specification covers a titanium alloy in the form of welding wire.
CURRENT
2016-06-16
Standard
AMS4956G
This specification covers a titanium alloy in the form of wire for welding filler metal.
CURRENT
2016-06-15
Standard
AMS4928V
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings, drawn shapes up through 6.000 inches (152.40 mm) inclusive in diameter or least distance between parallel sides and stock of any size for forging or flash welded rings.
CURRENT
2016-06-14
Standard
AMS4946E
This specification covers a titanium alloy in the form of seamless tubing.
CURRENT
2016-06-07
Standard
AMS4899D
This specification covers a titanium alloy in the form of sheet, strip, and plate up through 4.000 inches (101.60 mm), inclusive.
CURRENT
2016-05-31
Standard
AS6279A
This SAE Aerospace Standard (AS) establishes requirements applicable to metal stock that is ordered and produced in accordance with an Aerospace Material Specification (AMS). Topics include producer requirements, distributor requirements, size and grain orientation nomenclature, and purchaser ordering information to distributors. Requirements of this document have been developed to address titanium and titanium alloys, carbon and alloy steels, and corrosion and heat-resistant alloys.
2016-04-21
WIP Standard
AMS7498R
This specification covers flash welded rings made of titanium and titanium alloys.
Viewing 1 to 30 of 1048