Criteria

Text:
Display:

Results

Viewing 1 to 30 of 158
WIP Standard
2014-07-10
This document standardizes the knowledge, skills, and abilities inherent of all formally certified Aerospace Coatings Technicians. It shall provide clear guidelines for academic and other accredited organizations to teach a common language and critical core knowledge reflecting aircraft-specific coatings processes for complete aircraft and/or aircraft components.
WIP Standard
2013-10-09
1. SCOPE 1.1 Form This specification establishes requirements for a heat resistant aluminized organic coating with sufficient corrosion and erosion resistance. 1.2 Application The coating material covered by this specification is typically applied to the exterior of aluminum nacelle inlet lipskins of aircraft. It is suitable for use in a service temperature range from -65 to +600 °F (-54 to +316 °C). It is intended to have an appearance visually similar to sulfuric acid anodized aluminum. The liquid coating is suitable for spray application with high volume low pressure (HVLP) paint spray equipment. 1.3 Classification The coating material covered by this specification shall be classified as follows: Type 1 – A chrome free epoxy coating with less than 850 g/l Volatile Organic Compound (V.O.C.) content. 1.4 Safety - Hazardous Materials While the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use.
Standard
2013-07-22
This specification covers a ready-to mix, two component, self-curing, inorganic zinc rich primer for use on steel surfaces.
Standard
2013-07-22
This specification covers a two-component, polytetrafluoroethylene-filled polyurethane coating material supplied in kit form.
Standard
2013-07-22
This specification covers a semigloss black baking enamel based on a phenolic resin.
Standard
2013-07-22
This specification covers a corrosion and heat resistant aluminum coating material supplied as a liquid of suitable consistency for coating parts after being thoroughly mixed.
Standard
2013-07-22
This specification covers two-component colored systems composed of a resin and a miscible hardener supplied in kit form. Primarily for identification marking of parts and equipment exposed to temperatures from -55 to +150 degrees C (-65 to +300 degrees F) where various colors are needed. Systems produce tile-like compounds with good hardness, moisture and solvent resistance, and adhesion to metallic surfaces when properly cured.
Standard
2013-07-22
This specification covers a face-up type of water-applied, solvent-applied, or adhesive-applied decalcomanias.
Standard
2013-07-22
This specification covers an unpigmented silicone-resin-base coating material. Primarily for use on chemically or electrochemically treated magnesium and aluminum alloy surface to improve the high temperature corrosion and abrasion resistance and the air flow characteristics. The coating may also be used on steel for improvement of corrosion resistance.
Standard
2013-07-22
This specification covers a glyceryl-phthalate-base paint vehicle in the form of a liquid.
Standard
2013-07-22
This specification covers a zinc chromate primer in the form of a liquid.
Standard
2013-04-12
This specification covers the requirements for a high visibility, durable, exterior fluorescent paint system consisting of a pigmented fluorescent paint with a clear protective overcoating containing a weathering stabilizer. This paint system is capable of being removed without softening the permanent undercoats.
WIP Standard
2013-04-02
This specification covers two types of polyurethane coatings. The coating materials covered by this specification have been used typically for the protection of aircraft integral fuel tanks against corrosion from fuel contaminants but usage is not limited to such applications. They are suitable for use in a service temperature range from -65 to +250 °F (-54 to +121 °C).
Standard
2012-11-27
This specification establishes the requirements for a waterborne, corrosion inhibiting, chemical and solvent resistant, anodic electrodeposition epoxy primer capable of curing at 200 to 210 °F (93 to 99 °C).
Standard
2012-01-16
This specification covers a gloss, engine-gray baking enamel based on a glyceryl phthalate resin.
Standard
2012-01-16
This specification covers a gloss, black baking enamel based on a glyceryl phthalate resin.
Standard
2012-01-16
This specification covers a colored but unpigmented varnish based on a phenolic resin.
Standard
2011-09-23
This specification covers an ocher-pigmented primer.
Standard
2011-04-19
This specification establishes the performance requirements for non-chromated materials used for surface preparation of metallic aircraft surfaces prior to applying organic coatings.
WIP Standard
2011-02-28
The specification would establish requirements for the application of heavy-duty, super pentrating, water displacing corrosion inhibiting compound that can be applied by conventional airless or air-operated spray equipment and after drying form a firm transparent discernible protective coating with a low film weight.
WIP Standard
2009-09-02
This specification covers two types of two-component, epoxy, chemical and solvent resistant primer coatings formulated primarily for spray application. Coatings shall be compatible with epoxy and polyurethane topcoats.
Standard
2009-06-18
This specification has been declared “CANCELLED” by the Aerospace Materials Division, SAE, as of June 2009. By this action, this document will remain listed in the Numerical Section of the Index of Aerospace Material Specifications indicating that it has been “CANCELLED”. Cancelled specifications are available from SAE.
Standard
2009-06-18
This specification has been declared “CANCELLED” by the Aerospace Materials Division, SAE, as of June 2009. By this action, this document will remain listed in the Numerical Section of the Index of Aerospace Material Specifications indicating that it has been “CANCELLED”. Cancelled specifications are available from SAE.
Standard
2009-06-18
This specification has been declared “CANCELLED” by the Aerospace Materials Division, SAE, as of June 2009. By this action, this document will remain listed in the Numerical Section of the Index of Aerospace Material Specifications indicating that it has been “CANCELLED”. Cancelled specifications are available from SAE.
Standard
2009-06-17
This specification has been declared “CANCELLED” by the Aerospace Materials Division, SAE, as of June 2009. By this action, this document will remain listed in the Numerical Section of the Index of Aerospace Material Specifications indicating that it has been “CANCELLED”. Cancelled specifications are available from SAE.
Standard
2009-06-17
This specification has been declared “CANCELLED” by the Aerospace Materials Division, SAE, as of June 2009. By this action, this document will remain listed in the Numerical Section of the Index of Aerospace Material Specifications indicating that it has been “CANCELLED”. Cancelled specifications are available from SAE.
Standard
2009-06-17
This specification covers an unpigmented silicone-resin-base coating material. Primarily for use on chemically or electrochemically treated magnesium and aluminum alloy surface to improve the high temperature corrosion and abrasion resistance and the air flow characteristics. The coating may also be used on steel for improvement of corrosion resistance.
Standard
2009-06-16
This specification has been declared “CANCELLED” by the Aerospace Materials Division, SAE, as of June 2009. By this action, this document will remain listed in the Numerical Section of the Index of Aerospace Material Specifications indicating that it has been “CANCELLED”. Cancelled specifications are available from SAE.
Standard
2009-06-16
This specification has been declared “CANCELLED” by the Aerospace Materials Division, SAE, as of June 2009. By this action, this document will remain listed in the Numerical Section of the Index of Aerospace Material Specifications indicating that it has been “CANCELLED”. Cancelled specifications are available from SAE.
Viewing 1 to 30 of 158