Criteria

Text:
Display:

Results

Viewing 1 to 30 of 155
Standard
2014-05-07
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing. Other properties such as fatigue behavior, corrosion resistance, impact properties, etc., are beyond the scope of this document and responsibility for ensuring the acceptability of the product for applications where conditions warrant consideration of these other properties shall be borne by the end user.
Standard
2013-04-29
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing. Other properties such as fatigue behavior, corrosion resistance, impact properties, etc., are beyond the scope of this document and responsibility for ensuring the acceptability of the product for applications where conditions warrant consideration of these other properties shall be borne by the end user.
Standard
2013-04-16
This small solid rivet standard covers the complete general and dimensional data for flat head, pan head, button head, truss head, countersunk head, copper's, tinner's and belt rivets. Design and assembly data are given in the Appendix—Rivet Selection and Design Considerations. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Consumers are requested to consult with manufacturers concerning stock production sizes.
Standard
2013-04-16
SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.
Standard
2013-04-16
This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications. It is the objective of this document to insure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly. Appendix A is included to provide a recommended technique for measuring the case depth on the screws.
Standard
2013-04-16
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement of the mating metal or plastic studs and in some cases screw or bolt threads if considered adequate for the fastening joint appalications. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the metric equivalent of this document, see SAE J892M.
Standard
2013-04-16
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement of the mating metal or plastic studs and in some cases screw or bolt threads if considered adequate for the fastening joint applications. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the inch equivalent of this document, see SAE J892.
Standard
2013-04-16
Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.
Standard
2013-04-15
This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.
Standard
2013-04-15
This SAE Information Report is provided as an advisory guide. Careful discretion as to application is recommended. The content has been presented as accurately as possible, but responsiblity for its application lies with the user. It covers finishes applied to fasteners and related topics, corrosion resistance, lubricity, electrical grounding, ultraviolet light, and embrittlement. Table 1 lists these coatings and their properties so that finish selection can be reasonably made in accordance with known and anticipated fastener assembly applications. Application of protective coatings will affect fastener dimensions. This is especially critical for the thread fit of mating parts because the pitch diameter increases by four times the coating thickness. Explanation is covered in Section 5.
Standard
2013-04-15
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. The document covers the variables in the torque-tension relationship: friction, materials, temperature, humidity, fastener and mating part finishes, surfaces, and the kind of wrenching employed. Also described in this document is the torque management required to achieve correct fastener joint tightening. The thread fit of fasteners must be in accordance with Class 2A for external and 2B for internal inch threads.
Standard
2013-04-15
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ANSI/ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
Standard
2013-04-15
This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.
Standard
2013-04-15
This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning. This document describes practices for the use of TIWs which are typically produced for use with SAE J429 Grade 5 and Grade 8 fasteners or their metric counterparts, although the same principals hold true for bolted joints using other fasteners. Users are advised to contact a manufacturer for advice on use of these products before using them with special fasteners or applications. This document defines and illustrates preferred installation and inspection methodologies. The contents of this document are presented as accurately as possible; however, responsibility for its application lies with the user.
Standard
2013-04-15
These specifications cover the mechanical and chemical requirements, and surface discontinuities limits for carbon steel solid rivets used in automotive and other related industries.
Standard
2013-04-15
Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.
Standard
2013-04-11
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE Standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.
Standard
2013-04-11
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the inch series version, see SAE J174.
Standard
2013-04-11
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE Standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.
Standard
2013-04-11
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a. Nonserrated shank bolts which are heat treated b. Serrated shank bolts which are case hardened
Standard
2013-04-11
This SAE Standard covers the chemical, metallurgical and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: (a) Nonserrated shank bolts which are heat treated and (b) Serrated shank bolts which are case hardened.
Standard
2013-04-11
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 1/4 through 1 in nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the metric version, see SAE J174M.
Standard
2013-02-25
Material--SAE 1010 or SAE 1111 steel or equivalent. Clevis pins shall be supplied either soft or cyanide hardened as specified. Clevis pins must be free from burrs, loose scale, sharp edges, and all other defects that might affect their serviceability. General tolerances for all dimensions are plus or minus 0.010 unless otherwise specified.
Standard
2013-02-25
This SAE Recommended Practice covers the mechanical and quality requirements for steel tapping screws used in automotive and related industries. It does not apply to corrosion resistant (stainless) steel screws. (Dimensional requirements for most types of screws mentioned herein are covered in SAE J478.) The primary objective of the specification is to insure that screws form or cut mating threads in materials of construction into which they are normally driven, without deforming their own thread and without breaking during assembly or service. Certain limitations on basic material and manufacturing processes have been incorporated because the size and configuration of the parts under consideration make them vulnerable to relatively small variations in chemistry, heat treatment, etc., and because experience has shown that in processing it is difficult to keep these variables consistently "in balance." Until improved performance tests are developed, these limitations will supplement the "performance" features of the specification.
Standard
2013-02-18
This SAE Standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications. Products included are bolts, screws, studs, U-bolts, preassembled screw and washer assemblies (sems), and products manufactured the same as sems except without washer. Products not covered are tapping screws, thread-rolling screws, and self-drilling screws. Mechanical and material requirements for these products are covered in other SAE documents. The term stud as referred to herein, applies to a cylindrical rod of moderate length, threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. For specification purposes, this document treats U-bolts as studs. Thus, wherever the word studs appears, U-bolts is also implied.
WIP Standard
2013-02-04
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. The document covers the variables in the torque-tension relationship: friction, materials, temperature, humidity, fastener and mating part finishes, surfaces, and the kind of wrenching employed. Also described in this document is the torque management required to achieve correct fastener joint tightening. The thread fit of fasteners must be in accordance with Class 2A for external and 2B for internal inch threads.
Standard
2013-02-01
The Dryseal American Standard Taper Pipe Thread, the Dryseal American Fuel Internal Straight Pipe Thread and the Dryseal American Intermediate Internal Straight Pipe Thread covered by this standard conform with the American Standard ASA-B2.2. The Dryseal SAE-Short Taper Pipe Thread in this standard conforms with the Dryseal American Standard Taper Pipe Thread except for the length of thread, which is shortened for increased clearance and economy of material. The significant feature of the Dryseal thread is controlled truncation at the crest and root to assure metal to metal contact coincident with or prior to flank contact. Contact at the crest and root prevents spiral leakage and insures pressure-tight joints without the use of a lubricant or sealer. Lubricants, if not functionally objectionable, may be used to minimize the possibility of galling in assembly.
Standard
2013-01-08
This SAE Standard covers the mechanical and quality requirements for carbon steel, slotted and recessed, 82 degrees flat countersunk, 82 degrees oval countersunk, pan, fillister, hex, and hex washer head machine screws in sizes No. 4 through 3/4 in for use in automotive and related industries. The dimensions of these screws are covered in ASME B18.6.3.
Standard
2013-01-02
This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.
Standard
2013-01-02
This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.
Viewing 1 to 30 of 155