Criteria

Text:
Display:

Results

Viewing 1 to 30 of 158
2014-09-17
Standard
J1273_201409
SAE J1273 provides guidelines for selection, routing, fabrication, installation, replacement, maintenance, and storage of hose and hose assemblies for fluid-power systems. Many of these SAE Recommended Practices also may be suitable for other hoses and systems.
2014-09-09
WIP Standard
J343
This SAE Standard gives methods for testing and evaluating performance of the SAE 100R series of hydraulic hose and hose assemblies (hose and attached end fittings) used in hydraulic fluid power systems. Specific tests and performance criteria for evaluating hose assemblies used in hydraulic service are in accordance with the requirements for hose in the respective specifications of SAE J517. This document further establishes a uniform means of testing and evaluating performance of hydraulic hose assemblies.
2014-08-07
WIP Standard
J518/3
This SAE standard outlines general and dimensional specifications for Code 61 flange clamps (FCx & FCMx) for use in low pressure applications with J518-1 connections. For port dimensions, port design considerations, and flange head dimensions, please refer to J518-1. The rated working pressure of an assembly shall not exceed the least of all the component working pressure rated values. The following general specifications supplement the dimensional data contained in the tables with respect to all unspecified detail. Parts manufactured to this standard are also compatible with ISO 6162-1 port connections and flange heads.
2014-06-06
Standard
J1942_201406
SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 1991, as the official document for nonmetallic flexible hose assemblies for commercial marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. Refer to SAE J1527 Marine Fuel Hose for hose to convey gasoline or diesel fuel aboard small craft, including pleasure craft and related small commercial craft regulated directly or by reference under 33 CFR 183 Subpart J, and boats and yachts meeting American Boat and Yacht Council standards.
2014-06-06
Standard
J2552_201406
SAE J2552 provides limited, dimensional and general performance requirements for low pressure, field attachable, push on hose and their mating hose fittings. The intended application is for fluid and pneumatic power used with petroleum base hydraulic fluids, lube oils, water glycols and air, within the temperature ranges listed in Table 1. The maximum working pressure is 1.7 MPa (see Table 2). For air applications the maximum working pressure is at 0.7 MPa. Hose and hose fittings are manufactured within certain dimensions with tolerance ranges in order to provide the proper gripping and sealing. SAE J2552 hose from one manufacturer may not be compatible with SAE J2552 hose fittings supplied by another manufacturer. It is the responsibility of the fabricator to always follow the manufacturers’ instructions for proper preparation and fabrication of hose assemblies.
2014-06-05
Standard
J1475_201406
This SAE Standard covers general and performance specifications for hydraulic hose fittings of the styles, types, and classes defined in Section 3 and used in conjunction with nonmetallic flexible hoses for marine applications. This document does not ensure compatibility between manufacturers of hydraulic hose and hydraulic hose fittings. Compatibility is the responsibility of the hydraulic hose assembly manufacturer.
2014-06-04
Standard
J1927_201406
This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.
2014-06-04
Standard
J2545_201406
This SAE Recommended Practice identifies test procedures and parameters which may be used to evaluate, qualify and inspect non-SAE hydraulic hoses or other hose constructions which do not conform to any established ISO or national standards defining hydraulic hoses. (Non-SAE hydraulic hoses are defined as those which do not conform to the categories listed in SAE J517.) It is not intended for evaluating fluoropolymer lined hose constructions or hose constructions with working pressures above 86 MPa.
2014-05-28
WIP Standard
J1231
This SAE standard provides general and dimensional specifications for formed tube ends and hose fittings. These connections are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figures 2 and 3 are intended to be retained by hose clamps as specified in SAE J1508. It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.
2014-03-18
WIP Standard
J517
This SAE Standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 12 are applicable to all hydraulic hoses and supplement the detailed specifications for the 100R-series hoses contained in the later sections of this document. (See Tables 1A and 1B). This document shall be utilized as a procurement document only to the extent as agreed upon by the manufacturer and user. The maximum working pressure of a hose assembly comprising SAE J517 hose and hose connectors per SAE J516, SAE J518, SAE J1453, etc., shall not exceed the lower of the respective SAE maximum working pressure values. When using SAE J517 hose for marine applications, see SAE J1475, SAE J1942 and SAE J1942-1. The SAE J517 100R9, 100R10 and 100R11 hoses are discontinued due to lack of demand. For DOD orders see Appendix C.
2013-04-20
WIP Standard
J518/2
This SAE Standard covers general and dimensional specifications for the Code 62 metric (type 1) and inch (type 2) flanged heads, flange clamps (FC and FCM), and split flange clamps (FCS & FCSM) applicable to four-screw flange type tube, pipe, and hose connections. Also included are the recommended port dimensions and port design considerations. Type 2 (inch) flange clamps and split flanges are not for new design. The flange heads specified are incorporated into fittings having suitable means for attachment of tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections. The rated working pressure of an assembly shall not exceed the least of all the component working pressure rated values. The following general specifications supplement the dimensional data contained in the tables with respect to all unspecified detail.
2013-03-05
Standard
J518_201303
Superseded by SAE J518/1 and SAE J518/2. This SAE standard covers complete general and dimensional specifications for the flanged heads and split flange clamp halves applicable to 4-bolt split flange type tube, pipe, and hose connections with appropriate references to the O-ring seals and attaching components used in their assembly. Also included are recommended port dimensions and port design considerations. The flanged heads specified are incorporated into fittings having suitable means for attachment to tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections. THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J518 HOSE CONNECTIONS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES. Flanged heads shall be as specified in Figure 3 and Table 1.
2013-02-13
Standard
J1467_201302
This SAE Standard covers material and dimensional requirements of steel clip fastener fittings. These fittings are intended for use in hydraulic systems on industrial equipment primarily in mining applications.
2013-02-04
Standard
J517_201302
This SAE Standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 12 are applicable to all hydraulic hoses and supplement the detailed specifications for the 100R-series hoses contained in the later sections of this document. (See Tables 1A and 1B). This document shall be utilized as a procurement document only to the extent as agreed upon by the manufacturer and user. The maximum working pressure of a hose assembly comprising SAE J517 hose and hose connectors per SAE J516, SAE J518, SAE J1453, etc., shall not exceed the lower of the respective SAE maximum working pressure values. When using SAE J517 hose for marine applications, see SAE J1475, SAE J1942 and SAE J1942-1. The SAE J517 100R9, 100R10 and 100R11 hoses are discontinued due to lack of demand. For DOD orders see Appendix C.
2013-01-02
Standard
J1754/1_201301
This SAE Standard covers steel wire reinforced rubber hose assemblies using connectors specified in SAE J516 for use in hydraulic systems using petroleum based hydraulic fluids with maximum working pressures of 1.7 to 42 MPa. See SAE J1754-2, Table 8 for hose operating temperature ranges and identification codes. Note: Working pressure is defined as maximum system pressure.
2013-01-02
Standard
J518/1_201301
This SAE Standard covers general and dimensional specifications for the Code 61 metric (type 1) and inch (type 2) flanged heads, flange clamps (FC & FCM), and split flange clamps (FCS & FCSM) applicable to four-screw flange type tube, pipe, and hose connections. Also, included are the recommended port dimensions and port design considerations. Type 2 (inch) flange clamps and split flanges are not for new design. The flange heads specified are incorporated into fittings having suitable means for attachment of tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections. The rated working pressure of an assembly shall not exceed the least of all the component working pressure rated values. The following general specifications supplement the dimensional data contained in the tables with respect to all unspecified detail.
2013-01-02
Standard
J518/2_201301
This SAE Standard covers general and dimensional specifications for the Code 62 metric (type 1) and inch (type 2) flanged heads, flange clamps (FC and FCM), and split flange clamps (FCS & FCSM) applicable to four-screw flange type tube, pipe, and hose connections. Also included are the recommended port dimensions and port design considerations. Type 2 (inch) flange clamps and split flanges are not for new design. The flange heads specified are incorporated into fittings having suitable means for attachment of tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections. The rated working pressure of an assembly shall not exceed the least of all the component working pressure rated values. The following general specifications supplement the dimensional data contained in the tables with respect to all unspecified detail.
2012-05-08
Standard
J1405_201205
The procedures contained in this SAE Recommended Practice have been developed to establish uniform methods for impulse and high temperature circulation testing of hydraulic hose assemblies under special conditions not specified in SAE J343 for SAE J517 hoses. Basic test procedures are to be in accordance with SAE J343 except as modified in this document.
2012-01-06
Standard
J343_201201
This SAE Standard gives methods for testing and evaluating performance of the SAE 100R series of hydraulic hose and hose assemblies (hose and attached end fittings) used in hydraulic fluid power systems. Specific tests and performance criteria for evaluating hose assemblies used in hydraulic service are in accordance with the requirements for hose in the respective specifications of SAE J517. This document further establishes a uniform means of testing and evaluating performance of hydraulic hose assemblies.
2011-10-25
Standard
J516_201110
This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 15 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user. Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies. THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J516 FITTINGS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES.
2011-10-25
Standard
J2631_201110
This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.
2011-05-16
Standard
J1231_201105
This SAE standard provides general and dimensional specifications for formed tube ends and hose fittings. These connections are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figures 2 and 3 are intended to be retained by hose clamps as specified in SAE J1508. It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.
2010-12-30
Standard
J1942/1_201012
Effective August 28, 1991, the SAE replaced the USCG as the listing agency for Marine Hose Assemblies. The previous USCG list was discontinued as of December 31, 1992, and is being replaced by this SAE listing, J1942-1. All products appearing on the USCG list as of December 31, 1992, may be carried over to the SAE J1942-1 provided they meet the new test requirements listed in SAE J1942. If your products comply, you may retain your listings with no additional testing. (Please note that the USCG has the authority to request and inspect your test results at their discretion.) The following list consists of hose data provided as of May 2003, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25(c). Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting.
2010-08-05
Standard
J1754/2_201008
This SAE Standard covers ordering information for steel wire reinforced rubber hose assemblies using connectors specified in SAE J516 for use in hydraulic systems using petroleum based hydraulic fluids with maximum working pressures of 1.7 to 42 MPa. See SAE J1754-2, Table 8 for hose operating temperature ranges and identification codes. Note: Working pressure is defined as maximum system pressure.
2010-08-05
Standard
J1754/3_201008
This SAE Standard covers ordering information for J517 100R Series hose materials for hydraulic hose assemblies using connectors specified in SAE Standard J516 or all parts of ISO 12151 for use in hydraulic systems using petroleum based hydraulic fluids.
2010-08-05
Standard
J1402_201008
This recommended practice covers minimum requirements for air brake hose assemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines with air pressures up to 1 MPa, that are exposed to potential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of -40 °C to +100 °C.
2010-08-05
Standard
J343_201008
This SAE Standard gives methods for testing and evaluating performance of the SAE 100R series of hydraulic hose and hose assemblies (hose and attached end fittings) used in hydraulic fluid power systems. Specific tests and performance criteria for evaluating hose assemblies used in hydraulic service are in accordance with the requirements for hose in the respective specifications of SAE J517. This document further establishes a uniform means of testing and evaluating performance of hydraulic hose assemblies.
2010-05-17
Standard
J517_201005
This SAE Standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 12 are applicable to all hydraulic hoses and supplement the detailed specifications for the 100R-series hoses contained in the later sections of this document. (See Tables 1A and 1B). This document shall be utilized as a procurement document only to the extent as agreed upon by the manufacturer and user. The maximum working pressure of a hose assembly comprising SAE J517 hose and hose connectors per SAE J516, SAE J518, SAE J1453, etc., shall not exceed the lower of the respective SAE maximum working pressure values. When using SAE J517 hose for marine applications, see SAE J1475, SAE J1942 and SAE J1942-1. The SAE J517 100R9, 100R10 and 100R11 hoses are discontinued due to lack of demand. For DOD orders see Appendix C.
2010-02-24
Standard
J1754/2_201002
This SAE Standard covers ordering information for steel wire reinforced rubber hose assemblies using connectors specified in SAE J516 for use in hydraulic systems using petroleum based hydraulic fluids with maximum working pressures of 1.7 to 42 MPa. See SAE J1754-2, Table 8 for hose operating temperature ranges and identification codes. Note: Working pressure is defined as maximum system pressure.
2010-02-24
Standard
J1754/3_201002
This SAE Standard covers ordering information for J517 100R Series hose materials for hydraulic hose assemblies using connectors specified in SAE Standard J516 or all parts of ISO 12151 for use in hydraulic systems using petroleum based hydraulic fluids.
Viewing 1 to 30 of 158