Search Results

Standard

Hydraulic Tube Fittings

2012-01-06

CURRENT

J514_201201

This SAE Standard covers complete general and dimensional specifications for 37 degree flared and flareless types of hydraulic tube fittings and O-ring plugs. Also included are pipe fittings and adapter unions for use in conjunction with these tube fittings. These fittings are intended for general application in hydraulic systems on industrial equipment and commercial products. These fittings are capable of providing leakproof, full flow connections in hydraulic systems operating at working pressures as specified in Table 1 for respective sections. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, the values shown in SAE J1065 should not be construed as a guaranteed minimum. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and fitting manufacturer to assure that performance levels will be safe and satisfactory.

Standard

Specification for O-Ring Face Seal Connectors: Part 1—Tube Connection Details and Common Requirements for Performance and Tests

2011-08-04

HISTORICAL

J1453/1_201108

The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal (ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube diameters of 6 mm through 50 mm.

Standard

Connections for Fluid Power and General Use - Hydraulic Couplings - Diagnostic Port Sizes and Locations

2010-08-05

HISTORICAL

J1298_201008

SAE J1298 covers the recommended diagnostic port sizes for use in measuring hydraulic fluid temperature, pressure, flow, and for obtaining fluid samples. See SAE J1502 for the detailed coupling specifications.

Standard

Connector for Fluid Power and General Use—Ports and Stud End with ASME B1.1 Threads and O-Ring Seal—Part 4: External Hex and Internal Hex Inch Port Plugs—Dimensions, Design, Test Methods and Requirements

2010-08-05

CURRENT

J1926/4_201008

This part defines performance requirements, dimensions, and designs for −2 through −32 internal and external hex port plugs for use in SAE J1926-1 ports. Testing and usage through many years confirm the performance requirements of port plugs made from carbon steel. The port plugs were specified in SAE J514 without any performance requirements. They have been developed and tested to gain a 4:1 working pressure rating for industrial applications. In fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under pressure within an enclosed circuit. In general applications, a fluid may be conveyed under pressure. Components are connected through their threaded ports by stud ends on fluid conductor fittings to tubes and pipes or to hose fittings and hoses. For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, only ISO 6149 shall be used.

Standard

Connections for General Use and Fluid Power—Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing—Part 3: Light-Duty (L-Series) Stud Ends

2010-03-12

HISTORICAL

J1926/3_201003

This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable light-duty (L series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them. Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 35 MPa for nonadjustable and adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud end specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications. Conformance to the dimensional Information does not guarantee rated performance.

Standard

Connections for General Use and Fluid Power—Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing—Part 2: Heavy-Duty (S Series) Stud Ends

2010-03-12

HISTORICAL

J1926/2_201003

This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable heavy-duty (S series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them that are currently not listed in SAE J515. Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 41.3 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications. NOTE: This document specifies inch as well as metric hexes for the stud ends.

Standard

Connections for General Use and Fluid Power—Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing—Part 1: Threaded Port with O-Ring Seal in Truncated Housing

2010-02-15

HISTORICAL

J1926/1_201002

This part of SAE J1926 specifies dimensions for fluid power and general use ports with inch threads in accordance with ASME B1.1 for use with adjustable and nonadjustable stud ends shown in SAE J1926-2 and SAE J1926-3. Ports in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new designs in hydraulic fluid power applications.

Standard

Specification for O-Ring Materials Used with Hydraulic Connectors

2010-01-07

HISTORICAL

J515_201001

SAE J515 covers the specification for hydraulic O-ring material and properties and sizes applicable to face seal fittings, metric and inch stud ends, and four-bolt flange fittings. The standard includes a size code to allow industry and government agencies to order O-ring with a coded part number.

Standard

Specification for O-Ring Face Seal Connectors: Part 3—Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Connectors, Caps, and Connectors with SAE J1926-2 Inch Stud Ends

2009-08-21

HISTORICAL

J1453/3_200908

The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal (ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube diameters of 6 mm through 38 mm and for nominal hose diameters 6.3 mm through 38 mm. SAE J1453-3 covers the requirements for “inch based” O-ring face seal connectors to inch stud ends along with the associated adapters, bulkhead and union connectors. Inch hex wrenching flats are predominantly used throughout this standard.

Standard

Connections for Fluid Power and High Pressure Use—Ports, Stud Ends, and Plugs with ISO 261 Threads and O-Ring Sealing—Part 1: Ports with Recessed Conical Seat Requirements, Dimensions, Design, and Test Methods

2009-08-12

HISTORICAL

J2337/1_200908

This part of SAE J2337 specifies dimensions, design, and performance requirements for eight ports using a conical seal to insure leak proof performance with a design factor of 4 to 1.

Standard

Connector for Fluid Power and General Use—Ports and Stud End with ASME B1.1 Threads and O-Ring Seal—Part 4: External Hex and Internal Hex Inch Port Plugs—Dimensions, Design, Test Methods and Requirements

2009-07-29

HISTORICAL

J1926/4_200907

This part defines performance requirements, dimensions, and designs for –2 through –32 internal and external hex port plugs for use in SAE J1926-1 ports. Testing and usage through many years confirm the performance requirements of port plugs made from carbon steel. The port plugs were specified in SAE J514 without any performance requirements. They have been developed and tested to gain a 4:1 working pressure rating for industrial applications. In fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under pressure within an enclosed circuit. In general applications, a fluid may be conveyed under pressure. Components are connected through their threaded ports by stud ends on fluid conductor fittings to tubes and pipes or to hose fittings and hoses. For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, only ISO 6149 shall be used.

Standard

Fitting—O-Ring Face Seal

2009-01-13

CURRENT

J1453_200901

This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.

Standard

Connections for Fluid Power and General Use—Hydraulic Couplings—Diagnostic Port Sizes and Locations

2008-05-15

HISTORICAL

J1298_200805

SAE J1298 covers the recommended diagnostic port sizes for use in measuring hydraulic fluid temperature, pressure, flow, and for obtaining fluid samples. See SAE J1502 for the detailed coupling specifications.

Standard

Lubrication Fittings

2008-05-15

HISTORICAL

J534_200805

This SAE Standard covers complete general and dimensional specifications for the various types of lubrication fittings and related threaded components intended for general application in the automotive and allied fields.

Standard

Connections for Fluid Power and General Use--Ports and Stud Ends with ISO 261 Metric Threads and O-Ring Sealing, Part 3: Light-Duty (L Series) Stud Ends--Dimensions, Design, Test Methods, and Requirements

2007-12-21

CURRENT

J2244/3_200712

This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable light-duty (L series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 40 MPa for nonadjustable stud ends and 31.5 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydraulic fluid power applications. Conformance to the dimensional information in this SAE Standard does not guarantee rated performance.

Standard

Connections for Fluid Power and General Use--Ports and Stud Ends with ISO 261 Threads and O-Ring Sealing Part 2: Heavy-Duty (S Series) Stud Ends--Dimensions, Design, Test Methods, and Requirements

2007-12-21

CURRENT

J2244/2_200712

This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable heavy-duty (S Series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa for nonadjustable stud ends and 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used for new designs in hydraulic fluid power applications. Conformance to the dimensional information in this standard does not guarantee rated performance.

Standard

Connections for Fluid Power and General Use--Ports and Stud Ends with ISO 261 Threads and O-Ring Sealing--Part 4: Heavy-Duty (S Series) External Hex Port Plugs--Dimensions, Design, Test Methods, and Requirements

2007-12-21

CURRENT

J2244/4_200712

This part of SAE J2244 specifices dimensions, performance requirements, and test procedures for metric external hex O-rings port plugs. Port plugs in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydrualic fluid power applications. Conformance to the dimensional information in this document does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance ratings.

Standard

Connections for Fluid Power and General Use—Ports and Stud Ends with ISO 261 Threads and O-Ring Sealing Part 1: Port with O-Ring Seal in Truncated Housing

2007-12-21

CURRENT

J2244/1_200712

This part of SAE J2244 specifies dimensions for fluid power metric ports for use with adjustable and nonadjustable stud ends shown in SAE J2244/2. Ports in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa for nonadjustable stud ends and 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used for new designs in hydraulic fluid power applications.

Standard

Coding Systems for Identification of Fluid Conductors and Connectors

2007-12-13

HISTORICAL

J846_200712

This coding system is intended to provide a convenient means of identifying the various tube, pipe, hydraulic hose type and hose fittings, not intended for use in aircraft and of transmitting technical or engineering information relating to them wherever drawings or other pictorial media may not be readily available. The code has been kept flexible to permit expansion to cover new fitting categories or styles and, if the need develops, the inclusion of additional materials. The system is also compatible with automatic data processing equipment. It is not intended that this code should supersede established systems or means of identification. Therefore, it should be the prerogative of the user to apply the code which best satisfies his requirements.

Standard

Flares for Tubing

2007-09-04

HISTORICAL

J533_200709

This SAE Standard covers specifications and performance requirements for 37° and 45° single and double flares for tube ends intended for use with SAE J512, SAE J513, SAE J514, and ISO 8434-2 connectors. Considerations such as the effects of wall thickness selection for specific working pressures, identifying appropriate length of thread engagements for specific applications with mating connectors and other associated criteria, shall be the responsibility of the user. For applicable nominal reference working pressures for hydraulic tubing see SAE J1065 and ISO 10763.