Criteria

Text:
Display:

Results

Viewing 1 to 30 of 76
2014-01-10
WIP Standard
J701
The information in this SAE Information Report is the result of studies by the Automobile Manufacturers Association, American Trucking Association, and Truck Trailer Manufacturers Association, to achieve interchangeability of equipment which will comply with the legal dimensional limitations for the majority of states and yet permit increased loading space within these dimensions. This in no way supersedes other information in the SAE Handbook on this subject. Some cases will require more care in application allowing splash shield clearance at trailer support interference points and positioning fifth wheel to allow trailer swing clearance on an 11% grade. All dimensions are given in inches. Table 1 and Figures 1 and 2 show basic requirements for interchangeability of truck tractor and semitrailer equipment. Figure 3 shows the interchangeability of the doubles converter dolly.
2014-01-03
Standard
J701_201401
The information in this SAE Information Report is the result of studies by the Automobile Manufacturers Association, American Trucking Association, and Truck Trailer Manufacturers Association, to achieve interchangeability of equipment which will comply with the legal dimensional limitations for the majority of states and yet permit increased loading space within these dimensions. This in no way supersedes other information in the SAE Handbook on this subject. Some cases will require more care in application allowing splash shield clearance at trailer support interference points and positioning fifth wheel to allow trailer swing clearance on an 11% grade. All dimensions are given in inches. Table 1 and Figures 1 and 2 show basic requirements for interchangeability of truck tractor and semitrailer equipment. Figure 3 shows the interchangeability of the doubles converter dolly.
2011-09-12
Standard
J2181_201109
This test procedure is used to determine the steady-state directional control response of vehicles by measuring steady-state cornering behavior. Due to the wide range of operational conditions to which a vehicle can be subjected, the results of this testing do not provide a complete description of a vehicle's total dynamic behavior; in particular, the procedure does not test the vehicle's response during transient maneuvers. To fully assess a vehicle's total dynamic behavior, it would be necessary to conduct other test procedures in order to evaluate the vehicle's performance as a whole. The extent of instrumentation and the required accuracy of the measurement will be dependent on the goals of the personnel conducting the test. If it is desired simply to determine the general performance characteristics of a vehicle, then this test can be conducted with minimal instrumentation and test item preparation. This SAE Recommended Practice establishes a uniform procedure for determining the steady-state directional control response of trucks, buses, and combination vehicles.
2011-09-12
Standard
J2228_201109
This SAE Recommended Practice applies to upper coupler kingpins for commercial trailers and semitrailers conforming to the dimensional requirements of SAE J700 when new and originally installed. The dimensions of SAE J700 are the frame of reference for this document.
2011-09-12
Standard
J848_201109
This SAE Recommended Practice applies to fifth wheel kingpins for heavy-duty commercial trailers and semitrailers, used for off highway operation or in hauling heavy loads (see Figure 1.)
2011-09-12
Standard
J336_201109
This SAE Recommended Practice describes the equipment and procedure for determining the truck cab interior sound level over the upper half of the engine speed range. This practice applies to motor trucks and truck-tractors and does not include construction and industrial machinery.
2011-09-12
Standard
J366_201109
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
2011-07-13
Standard
J847_201107
This SAE Recommended Practice applies to highway trailer tow bar eye-type applications, including multiple trailers.
2011-07-13
Standard
J133_201107
The purpose of this SAE Recommended Practice is to establish test procedures and minimum performance standards for kingpins and their supporting structure manufactured to SAE specifications. The dimensions shown in SAE J700 will permit the establishment of standard clearances in the installed condition which, in turn, will permit fifth wheel manufacturers to design their products to establish interchangeability with any kingpin made and installed to the SAE specification.
2011-07-13
Standard
J697_201107
This SAE Recommended Practice is intended as a guide for manufacturers and users of trailers, specifically full trailer(s) and/or converter dollies. Its inclusion in state, federal, or any laws or regulations where flexibility of revision is lacking is discouraged. Emergency safety is the basis of this recommendation. This SAE Recommended Practice covers the number, location, and method of attachment of safety chains for full trailers and/or converter dollies.
2011-07-13
Standard
J700_201107
This SAE Standard applies to upper coupler kingpins for commercial trailers and semitrailers in the unladen condition. See Figure 1. A 90 degree ± 1 degree angle extends (in all directions) from the centerline of the kingpin to the upper coupler plate surface within a 48.26 cm (19 in) radius. The upper coupler plate surface should not bow downward (convex) more than 0.635 cm (1/4 in) within a 48.26 cm (19 in) radius or more than 0.3175 cm (1/8 in) at a radius of 25.4 cm (10 in) from the kingpin. The upper coupler plate surface should not bow upward (concave) more than 0.15875 cm (1/16 in) within a 48.26 cm (19 in) radius. (See Figure 2.) NOTE--For recommended performance, see SAE J133.
2011-06-13
Standard
J875_201106
The scope of this SAE Recommended Practice, trailer axle alignment, is to identify the dimensional limits of, and a method to, establish a perpendicular relationship between the king pin centerline and the axle centerline at its midpoint. Various types of equipment are commercially available which can be used for this measurement which provides varying degrees of accuracy, but none can be endorsed by SAE. The most fundamental methods of measurement will be described here, but other equipment is available if a greater degree of accuracy is desired.
2011-06-13
Standard
J699_201106
This SAE Recommended Practice establishes limits for empty vehicle floor heights and provides limits of vehicle dimensions for use in designing docking facilities for motor vehicles.
2011-06-13
Standard
J691_201106
This SAE Recommended Practice sets forth recommended back of cab to rear axle (CA) dimensional data. It applies to 4- and 6-wheel motor trucks but not necessarily to truck-tractors.
2011-06-13
Standard
J693_201106
To aid in obtaining overall widths across dual tires when requirements of frame widths, spring widths, chain clearance, and standard rim sizes are considered.
2011-06-13
Standard
J695_201106
This SAE Recommended Practice sets forth a method by which the turning ability and off tracking of motor vehicles can be determined.
2011-05-17
Standard
J2180_201105
The test procedure applies to roll coupled units such as straight trucks, tractor semitrailers, full trailers, B-trains, etc. The test is aimed at evaluating the level of lateral acceleration required to rollover a vehicle or a roll-coupled unit of a vehicle in a steady turning situation. Transient, vibratory, or dynamic rollover situations are not simulated by this test. Furthermore, the accuracy of the test decreases as the tilt angle increases, although this is a small effect at the levels of tilt angle used in testing heavy trucks. The test accuracy is accepted for vehicles that will rollover at lateral acceleration levels below 0.5 g corresponding to a tilt table angle of less than approximately 27 degrees. Even so, the results for heavy trucks with rollover thresholds greater than 0.5 g could be used for comparing their relative static roll stability.
2011-05-17
Standard
J2245_201105
This SAE Recommended Practice provides general guidelines for measuring the splash and spray produced by vehicles operating over wet pavements. The guidelines describe both the video digitizing and the laser methods of analysis. The video-digitizing method uses video images and contrast measurements between black and white checkerboards when a spray cloud is superimposed on them as a means of measuring the obscuring spray. The laser method uses laser transmittance through the spray cloud as the means of measurement. It is left to the users of this practice to decide which method is best suited to their needs. There is no implied relationship between these two methods, although it is expected that the ranking of relative spray reduction between test vehicle configurations would be approximately the same. All sections listed in this document are to be considered as common to both methods, unless otherwise noted.
2011-05-17
Standard
J682_201105
For guidance only in regard to highway commercial motor vehicles where protection to the rear against rear wheel splash and stone throw is deemed necessary, the following clearance specifications are recommended.
2011-05-17
Standard
J683_201105
The purpose of this SAE Information Report is to set up a guide as to body, frame, and wheel housing clearance to accommodate tire chains, and also the minimum bogie spacing to permit using chains on both axles. These dimensions apply to trucks, buses, and combinations of vehicles 10 001 lb (4535.06 kg) GVW and over, and are based upon recommendations of the Tire and Rim Association and of the National Association of Chain Manufacturers. The diagram shows clearance for chains over the tire ONLY and allowance must be made for spring deflections in determining fender clearance.
2011-05-17
Standard
J1490_201105
There are two ways to assess the characteristics of ride vibrations of a vehicle during its operation. Subjective evaluation and objective measurement. Subjective assessments of the ride vibrations experienced by drivers during ride evaluations are generally performed by a panel of drivers and/or passengers who are instructed to operate or ride a group of vehicles in a predetermined manner in order to subjectively assess the levels and characteristics of ride vibrations. Figures 6A through 6C show examples of subjective evaluation forms presently in use. The disadvantages of the subjective method include need for careful experimental design, need for statistically unbiased samples, complexity of human perceptions of vibrations, and difficulty in comparing qualitative data of vehicles evaluated at different times and/or by different groups of people. Often ride characterization is not an easy task using only qualitative or descriptive terms. Therefore, it is necessary and desirable to develop objective techniques to enable ride engineers and others to measure ride vibrations during ride assessment in a quantitative manner.
2003-10-27
Standard
J133_200310
The purpose of this SAE Recommended Practice is to establish test procedures and minimum performance standards for kingpins and their supporting structure manufactured to SAE specifications. The dimensions shown in SAE J700 will permit the establishment of standard clearances in the installed condition which, in turn, will permit fifth wheel manufacturers to design their products to establish interchangeability with any kingpin made and installed to the SAE specification.
2003-01-01
Standard
J682_200301
For guidance only in regard to highway commercial motor vehicles where protection to the rear against rear wheel splash and stone throw is deemed necessary, the following clearance specifications are recommended.
2002-09-19
Standard
J2245_200209
This SAE Recommended Practice provides general guidelines for measuring the splash and spray produced by vehicles operating over wet pavements. The guidelines describe both the video digitizing and the laser methods of analysis. The video-digitizing method uses video images and contrast measurements between black and white checkerboards when a spray cloud is superimposed on them as a means of measuring the obscuring spray. The laser method uses laser transmittance through the spray cloud as the means of measurement. It is left to the users of this practice to decide which method is best suited to their needs. There is no implied relationship between these two methods, although it is expected that the ranking of relative spray reduction between test vehicle configurations would be approximately the same. All sections listed in this document are to be considered as common to both methods, unless otherwise noted.
2001-06-12
Standard
J336_200106
This SAE Recommended Practice describes the equipment and procedure for determining the truck cab interior sound level over the upper half of the engine speed range. This practice applies to motor trucks and truck-tractors and does not include construction and industrial machinery.
2001-04-27
Standard
J2228_200104
This SAE Recommended Practice applies to upper coupler kingpins for commercial trailers and semitrailers conforming to the dimensional requirements of SAE J700 when new and originally installed. The dimensions of SAE J700 are the frame of reference for this document.
2001-04-27
Standard
J848_200104
This SAE Recommended Practice applies to fifth wheel kingpins for heavy-duty commercial trailers and semitrailers, used for off highway operation or in hauling heavy loads (see Figure 1.)
2001-04-27
Standard
J366_200104
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
2001-04-27
Standard
J700_200104
This SAE Standard applies to upper coupler kingpins for commercial trailers and semitrailers in the unladen condition. See Figure 1. A 90 degree ± 1 degree angle extends (in all directions) from the centerline of the kingpin to the upper coupler plate surface within a 48.26 cm (19 in) radius. The upper coupler plate surface should not bow downward (convex) more than 0.635 cm (1/4 in) within a 48.26 cm (19 in) radius or more than 0.3175 cm (1/8 in) at a radius of 25.4 cm (10 in) from the kingpin. The upper coupler plate surface should not bow upward (concave) more than 0.15875 cm (1/16 in) within a 48.26 cm (19 in) radius. (See Figure 2.) NOTE--For recommended performance, see SAE J133.
2000-09-29
Standard
J2179_200009
The procedure applies to heavy vehicles weighing more than 11 800 kg (26 000 lb) and particularly to those vehicles having two or more articulation joints that allow rotation in a horizontal plane. The procedure pertains to the lateral directional response of multi-articulated vehicles in avoidance maneuvers performed at highway speeds without braking.
Viewing 1 to 30 of 76