Criteria

Text:
Display:

Results

Viewing 1 to 30 of 80
Standard
2014-02-03
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
Standard
2014-01-03
This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims, wheels for demountable rims, rim spacers designed for 28 degrees bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. This document is divided into two sections. Section 1 establishes the practice for new designs for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document.
WIP Standard
2013-08-13
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. For bolt together military wheels, see SAE J1992. This document does not cover other special application wheels and rims.
Standard
2013-05-23
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.
WIP Standard
2013-03-11
To provide uniform laboratory procedures and radial/lateral load pairs for biaxial fatigue testing of disc wheel intended for normal highway use on trucks, buses, and trailers applicable for the North America market. Load cases considered include steer, drive, and trailer vehicle positions. The radial/lateral load pairs are not specific to one particular vehicle or OEM manufacturer.
Standard
2013-02-11
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a. “N” trailer axle b. “R” powered rear axle c. “FF / FG” nonpowered front axle d. “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
WIP Standard
2013-02-06
This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document. This document defines wheel mounting systems and documents the dimensions and tolerances necessary to maintain serviceability, and interchangeability in the interface areas. To be consistent with ISO, it is divided into two sections (I and II). Section I is in concert with ISO 4107, describing mounting systems currently used internationally and nominated for, or included in, the international standard for bolt circle interfaces. Section II records information on current mounting systems also used in North America. Components of different mounting systems with common bolt patterns could be mis-assembled together and cause service problems. Therefore, it is important to note that each mounting system should be treated individually and their components not be intermixed.
Standard
2012-09-27
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.
WIP Standard
2012-09-05
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, U, W, R, N and P.
WIP Standard
2012-08-10
This SAE Recommended Practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. The geometric features described in this document are shown at true position. This document is intended for outboard mounted brake drums and disc wheel hubs used on Class 7 and 8 commercial vehicles. Special and less common applications are not covered. This document defines and documents the dimensions and tolerances necessary to maintain interchangeability in the interface areas.
WIP Standard
2012-06-15
This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheels and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.
Standard
2012-05-29
This SAE Recommended Practice establishes dimensions and tolerances for the interface between inboard mounted disc brake rotors and disc wheel hubs. The geometric features described in this document are shown at true position. This document is intended for inboard mounted disc brake rotors and disc wheel hubs for Class 5, 6, 7, and 8 commercial vehicles. Special and less common applications are not covered.
WIP Standard
2012-04-30
This SAE Recommended Practice defines a clearance line for establishing dimensional compatibility between drum brakes and 19.5 in, 22.5 in, and 24.5 in diameter wheels. Wheels designed for use with drum brakes may not be suitable for disc brake applications. The clearance line establisheds the maximum envelope for brakes and minimum envelope for complete wheels to allow for interchangeability. This document addresses the dimensional characteristics only, and makes no reference to the performance, operational dynamic deflections, or heat dissipation of the system. Valve clearances have not been included in the fitment lines. Bent valves may be required to clear brake drums. Disc brake applications may require additional running clearances beyond those provided by the minimum contour lines. Mounting systems as noted are referenced in SAE J694.
Standard
2012-04-23
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For wheels and rims intended for normal highway use on trucks and buses, see SAE J267. For wheels intended for normal highway use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. This document does not cover off-highway or other special application wheels and rims.
Standard
2012-03-15
This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of spoke wheels, hubs and hub-rotor assemblies on the following axle designations. a. FF b. FL c. FC d. FH e. L f. R g. U h. W j. N k. P
Standard
2011-04-14
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.
Standard
2011-03-30
This SAE Recommended Practice provides for standardized steel disc wheel radial runout low point marking. This marking is used for match-mounting tires on wheels to minimize assembly radial force variation. It applies to tubeless 15 degree drop center disc wheels for use on class 5, 6, 7, and 8 commercial vehicles.
Standard
2011-03-30
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rims, rim spacers, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
WIP Standard
2010-09-28
This SAE Recommended Practice applies to nuts as specified in SAE J694 and J1835 used for wheel and demountable rim attachment. Only the test methods necessary to assure proper wheel or rim assembly are specified. Fasteners for less common and special applications are not included. Purpose This document, to ensure proper assemblies, specifies test methods for Metric or English, one- or two-piece flange nuts, single ball seat nuts, inner and outer ball seat nuts, and rim clamp nuts.
Standard
2010-02-15
This SAE Recommended Practice provides for standardized steel disc wheel radial runout low point marking. This marking is used for match-mounting tires on wheels to minimize assembly radial force variation. It applies to tubeless 15 degree drop center disc wheels for use on class 5, 6, 7, and 8 commercial vehicles.
Standard
2009-10-12
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of spoke wheels and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hub and/or spoke wheel developer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or spoke wheel developer to modify other parameters to obtain satisfactory service life.
Standard
2008-10-31
This SAE Recommended Practice applies to nuts as specified in SAE J694 and J1835 used for wheel and demountable rim attachment. Only the test methods necessary to assure proper wheel or rim assembly are specified. Fasteners for less common and special applications are not included. Purpose This document, to ensure proper assemblies, specifies test methods for Metric or English, one- or two-piece flange nuts, single ball seat nuts, inner and outer ball seat nuts, and rim clamp nuts.
Standard
2008-08-22
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, U, W, R, N and P.
Standard
2008-07-17
This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging. The purpose of this document is to provide users of truck, trailer, and bus wheel seals a means of identifying the suppliers of all such components by use of the symbology utilized by the suppliers on their components and packaging.
Standard
2007-12-10
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. For bolt together military wheels, see SAE J1992. This document does not cover other special application wheels and rims.
Standard
2007-09-07
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rims, rim spacers, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
Standard
2007-07-31
This SAE Recommended Practice defines a clearance line for establishing dimensional compatibility between drum brakes and 19.5 in, 22.5 in, and 24.5 in diameter wheels. Wheels designed for use with drum brakes may not be suitable for disc brake applications. The clearance line establisheds the maximum envelope for brakes and minimum envelope for complete wheels to allow for interchangeability. This document addresses the dimensional characteristics only, and makes no reference to the performance, operational dynamic deflections, or heat dissipation of the system. Valve clearances have not been included in the fitment lines. Bent valves may be required to clear brake drums. Disc brake applications may require additional running clearances beyond those provided by the minimum contour lines. Mounting systems as noted are referenced in SAE J694.
Standard
2007-06-21
This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document. This document defines wheel mounting systems and documents the dimensions and tolerances necessary to maintain serviceability, and interchangeability in the interface areas. To be consistent with ISO, it is divided into two sections (I and II). Section I is in concert with ISO 4107, describing mounting systems currently used internationally and nominated for, or included in, the international standard for bolt circle interfaces. Section II records information on current mounting systems also used in North America. Components of different mounting systems with common bolt patterns could be mis-assembled together and cause service problems. Therefore, it is important to note that each mounting system should be treated individually and their components not be intermixed.
Standard
2007-04-30
This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheels and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.
Standard
2007-02-21
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.
Viewing 1 to 30 of 80