Search Results

By means of cooperation of CAE (computer aided engineering), design and experiment, based on dynamics, combustion, fluid and finite element, respectively establish engine dynamics, combustion, fluid and finite element model, proceed innovative research on engine thermal equilibrium, cooling heat dissipation and structural strength. Through the innovation research, create the JMC top-down design and analysis process, which makes JMC product development processes have significant innovation, Independently developed engine thermal equilibrium calculation program, can positively calculate engine thermal equilibrium and water jacket cooling.

Traditional hybrid vehicles operated two types of oil pump, mechanical for combustion engine and electrical for electric motor, to supply oil pressure for automatic transmission in each power source. New hybrid vehicles has only one electrical pump to reduce system volume and to improve fuel efficiency. Purposes of this study are to make standardization of firmware development process for oil pump unit (OPU) and electric oil pump (EOP) and to apply permanent magnet synchronous motor (PMSM) instead of brushless DC (BLDC) motor. In old-fashioned non-operating system (OS) firmware, it was convenient to calculate control timing for motor control, however the firmware was deeply dependent to specific microcontroller Unit (MCU). In other words, much of efforts and time are needed if new MCU were applied.

The crankshaft translates the reciprocatory motion of the piston into rotary motion. A flywheel is generally connected to the crankshaft to reduce the vibrating characteristic of four stroke cycle. Counterweights are added for each reciprocating piston to provide engine balance while operating. Gasoline engines have curtailed compression ratio therefore shorter stoke length as a deduction have higher RPM in comparison to diesel counterpart. A crankshaft is subjected to enormous stresses, potentially equivalent of several tones of force. Failure of the crankshaft is predominantly due to violent vibrations, insufficient lubrication, excessively pressurized cylinder. This research aims to examine the stress subjected to acute points on a crankshaft. Three dimension model of 4 stroke single cylinder engine crankshaft is modeled using SolidWorks v18. End conditions were applied taking into consideration the engine mountings of the crankshaft.

The emissions of two ultralow NOx heavy-duty (HD) vehicles equipped with 0.02 g/bhp-hr low NOx natural gas (NG) engines were evaluated on a chassis dynamometer. This included a waste hauler and a city transit bus, each with a 0.02 g/bhp-hr NOx L9N near zero (NZ) natural gas engine. The vehicles were tested over a variety of different cycles, including the Urban Dynamometer Driving Schedule (UDDS), port drayage cycles, transit bus cycles, and a refuse truck cycle. For both vehicles, the NOx emissions results were below the 0.02 g/bhp-hr level for most cycles, with the exception of some cold start tests. For the waste hauler, NOx emissions averaged between 0.014 and 0.002 g/bhp-hr for the hot start tests, and from 0.043 to 0.014 g/bhp-hr for the cold start tests. This represented NOx emissions reductions from 97%-100% of compared with previous ISL G 8.9 engines.

The introduction of the Worldwide Harmonised Light Vehicles Test Procedure (WLTP) and Real Driving Emissions (RDE) test requirements have put increased strain on vehicle and engine performance as well as the development of advanced engine technologies and emissions mitigation strategies. This requirement for increased development is a direct result of the need for new vehicles to comply with present and emerging emissions standards across an extended range of boundary conditions that include ambient temperature, altitude and driving style. To reduce the significant number of on-road test permutations that would ordinarily be required to validate a given vehicle across the defined RDE boundary conditions, a Road to Rig (R2R) development approach known as RDE Plus (RDE+) is being evolved at HORIBA MIRA.

Portable Emission Measurement Systems (PEMS) are used by the U.S. Environmental Protection Agency (EPA) to measure gaseous and particulate mass emissions from vehicles in normal, in-use, on-the-road operation to support many of its programs, including assessing mobile source emissions compliance, emissions factor assessment for in-use fleet modeling, and collection of in-use vehicle operational data to support vehicle simulation modeling programs. This paper discusses EPA’s use of Global Positioning System (GPS) measured altitude data and electronically logged vehicle speed data to provide real-world road grade data for use as an input into the Gamma Technologies GT-DRIVE+ vehicle model. The GPS measured altitudes and the CAN vehicle speed data were filtered and smoothed to calculate the road grades by using open-source Python code and associated packages.

As emerging automated vehicle technology is making advances in safety and reliability, engineers are also exploring improvements in energy efficiency with this new paradigm. Powertrain efficiency receives due attention, but also impactful is finding ways to reduce driving losses in coordinated-driving scenarios. Efforts focused on simulation to quantify road load improvements require a sufficient amount of background validation work to support them. This study uses a practical approach to directly quantify road load changes by testing the coordinated driving of two vehicles on a test track at various speeds (64, 88, 113 km/h) and vehicle time gaps (0.3 to 1.3 s). Axle torque sensors were used to directly measure the load required to maintain steady-state speeds while following a lead vehicle at various gap distances.

There is an increasing need to understand the discrepancy between the real-world driving emissions and the emissions determined from type approval in a laboratory. Currently all modern passenger cars and trucks in Europe must undergo an on-road driving emissions test with portable emissions measurement systems (PEMS). Due to the large volume and big operational effort the currently used PEMS has however the constraint for monitoring the emissions of a vehicle within a limited time. To cover as many real-world driving conditions as possible, an online measurement system with automatic functions in data taking, data transferring and data analysis is needed. A Smart Emissions Measurement System (SEMS) was developed by TNO to derive robust and reliable emission factors, this system provides a simple and easy-to-use emissions monitoring solution.

Super ultra-low NOX emission engine concepts are essential to comply with future emission legislations. To meet the future emission standards, application of advanced diesel exhaust aftertreatment systems (EATS), such as Diesel Oxidation Catalyst (DOC), Lean NOX Trap (LNT), Selective Catalytic Reduction coatings on Soot Filters (SCRF) and underfloor SCR, is required. Effective customized thermal management strategies are essential to ensure fast light-off of the EATS after engine cold start, and to avoid significant cooldown during part load operation. The authors describes the investigation of different exhaust gas heating measures, such as intake throttling, late fuel injection, exhaust throttling, advanced exhaust cam phasing, retarded intake cam phasing, cylinder deactivation, full turbine bypass, electric catalyst heating and electrically heated intake manifold strategies.

SCR on filter, also known as SCRoF, SCRF, SDPF, has been utilized to meet the stringent light duty Euro 6 emission regulations. Close-coupled DOC-DEF-SCR on filter with underfloor SCR architectures, offer a balance of NOx performance at cold start and highway driving conditions. In contrast, the DOC-DPF-DEF-SCR architecture has been most commonly selected to meet the on-road and non-road heavy duty emission regulations worldwide. Diesel engines applied to off road vehicles can operate under higher loads for extended times, producing higher exhaust temperatures and engine out NOx emissions. New European Stage V emission regulations will mandate diesel particulate filter (DPF) adoption because of particulate number and more stringent particulate mass requirements. Three aftertreatment architecture choices with diesel particulate filters (DPF) were evaluated as candidates to fulfill the Stage V emission regulations.

Reducing cold-start emissions to meet increasingly stringent emissions limits requires fast activation of exhaust system sensors and aftertreatment control strategies. One factor delaying the activation time of current exhaust sensors, such as NOx and particulate matter (PM) sensors, is the need to protect these sensors from water present in the exhaust system. Exposure of the ceramic sensing element to water droplets can lead to thermal shock and failure of the sensor. In order to prevent such failures, various algorithms are employed to estimate the dew point of the exhaust gas and determine when the exhaust system is sufficiently dry to enable safe sensor operation. In contrast to these indirect, model-based approaches, this study utilized radio frequency (RF) sensors typically applied to monitor soot loading levels in diesel and gasoline particulate filters, to provide a direct measurement of stored water levels on the ceramic filter elements themselves.

The development and validation of detailed simulation models of in-cylinder combustion, emission formation mechanisms and reaction kinetics in the exhaust system are of crucial importance for the design of future low-emission powertrain concepts. To investigate emission formation mechanisms on one side and to create a solid basis for the validation of simulation methodologies (e.g. 3D-CFD, multi-dimensional in-cylinder models, etc.) on the other side, specific detailed measurements in the exhaust system are required. In particular, the hydrocarbon (HC) emissions are difficult to be investigated in simulation and experimentally, due to their complex composition and their post-oxidation in the exhaust system. In this work, different emission measurement devices were used to track the emission level and composition at different distances from the cylinder along the exhaust manifold, from the exhaust valve onwards.

Understanding the chemical reactions taking place in the engine and after-treatment systems is indispensable for minimizing harmful emissions in automotive exhaust gas. Real time gas analyzers for engine exhaust play a vital role for developing mathematical models and evaluating new after-treatment technologies. Gas analyzers using Fourier Transform Infrared Spectroscopy (FTIR) offer the advantage of continuous non-destructive simultaneous multicomponent analysis of a single gas stream. The ability of such analyzers to detect concentration fluctuations in the sample gas depends on a balance between its sample gas replacement rate and data sampling frequency. Increasing the sampling frequency is useful for detecting rapid concentration fluctuations, provided that the sample gas replacement rate is fast enough. This is commonly achieved by increasing the sample flow rate.

Emissions of diesel engine have been received much more attention since the Volkswagen Emission Scandal. The Euro VI emission standard has already included cold start emissions in the legislative emission driving cycles which is one of the hardest part of emission control. High altitude performance is also considered in the latest regulations which will be stricter in the future. Heating the coolant is one of the most common method to improve the cold start performance. But researches focus on the emission of a diesel engine in different coolant temperature at high altitude which up to 4500m have not been seen. The present research investigated the effect of coolant temperature on performance and exhaust emissions (gaseous and particulate emissions) during the cold start of a diesel engine. A plateau simulation system controlled the inlet and exhaust pressure to create altitude environments from 0m to 4500m, and the coolant temperature was controlled from 20°C to 60°C.

An independent periodical technical inspection (PTI)*) of vehicles is proposed in the last time as a better prevention against increased emissions of the fleet. Several projects focused on the Diesel vehicles (HD & LD) and on the functionality of the exhaust aftertreatment systems as a key element for lowering emissions of a vehicle or machine. The present paper summarizes the results obtained on 3 modern passenger cars Euro 6b (with EGR, DOC, DPF & SCR) during load jumps, representing the heat-up or cool-down behaviour of the exhaust system. The portable devices for PTI were tested together with the stationary measuring systems of the engine laboratory. In the second part of the report, the present knowledge and proposals of supplementary test procedures (like IUC or PTI) were shortly described.

An experimental study was performed to investigate spark ignition and subsequent spark stretch evolution in an inert environment at high- flow velocities up to 32 m/s across the spark plug gap in a constant-volume optical combustion-vessel at pressures representative of those in an engine. The vessel is capable of generating various in-cylinder thermodynamic conditions representative of light-duty spark ignition engines. The characteristic behavior of the spark was investigated using both a high-speed optical diagnostics and electrical measurement. Charge gas pressures were varied from 15 to 45 bar. Results show that the spark, flowing downstream the spark plug, is subject to short circuits of the spark channel and/or restrikes. The frequency of the restrike increased with increased flow velocity and charge gas pressure and decreased discharge current level.

Diesel particulate filters are remarkably efficient in reducing emissions of particulate matter from heavy-duty diesel engines. However, their efficiency and performance are negatively impacted by contaminants derived from consumed engine lubricant. This accumulation of incombustible ash imparts a fuel economy penalty due to increased system backpressure and demand for more frequent regeneration events. This study documents a systematic evaluation of lubricant impacts on DPF ash loading, system performance, and fuel economy. A novel, ultra-low ash heavy-duty engine oil demonstrates significant advantages in aged systems when compared to tests using conventional lubricants. The ultra-low ash oil yields a significantly lower ash loading that is also more dense therefore offering extended DPF maintenance interval and potential for 3% fuel economy retention benefit. These advantages offer potential for significant reduction in cost to operate and maintain a DPF equipped engine.

The low-NOx standard for heavy-duty trucks proposed by the California Air Resources Board will require rapid warm-up of the aftertreatment system. Several different engine technologies are being considered to meet this need. In this study, a 1-D engine model was first used to evaluate several individual control strategies capable of increasing the exhaust enthalpy and decreasing the engine-out NOX over the initial portion of the cold start FTP cycle. The additional fuel consumption resulting from these strategies was also quantified with the model. Next, several of those strategies were combined to create a hypothetical aftertreatment warm-up mode for the engine. The model was then used to evaluate potential benefits of an air gap manifold (AGM) and two different turbine by-pass architectures. The detailed geometry of the AGM model was taken into account, having been constructed from a real prototype design.

Diesel engines have been the major power source for medium- to heavy-duty ground vehicles due to superior fuel efficiency and durability over gasoline engines. However, Diesel engines are the main contributors for non-renewable Diesel fuel consumption and NOx and particulate matter (PM) emissions. Biodiesel fuel has been considered as a promising alternative fuel and can be directly fed into Diesel engines without major modifications. In addition, biodiesel has demonstrated lower hydrocarbon (HC), carbon monoxide (CO), and PM emissions than Diesel fuel. Nevertheless, the NOx emissions of biodiesel are generally higher. To meet stringent NOx emission regulation, urea-based selective catalytic reduction (SCR) systems have been widely utilized in Diesel-powered vehicles. The application of biodiesel fuel to Diesel engines can significantly change the exhaust condition and thus increase the complexity of SCR design and controls.

Engine cylinder pressure is traditionally measured with a piezo-electric pressure transducer, and as such, must be referenced or pegged to a known value. Frequently, the cylinder pressure is pegged to the pressure in the intake manifold plenum whereby the manifold absolute pressure (MAP) at the end of the intake stroke is measured and the cylinder pressure trace for the entire cycle is adjusted such that the cylinder pressure is set equal to the manifold pressure at the end of the intake stroke. However, any error in pegging induces an error in the cylinder pressure trace, which has an adverse effect on the entire combustion analysis. This research is focused on assessing the pegging error for several pegging methods across a wide range of engine operating conditions, and ultimately determining best practices to minimize error in pegging and the calculated combustion metrics. The study was conducted through 1D simulations using the commercially available GT-Power.