Search Results

., driver assistance functions, intrusion detection system, vehicle diagnostics, external device authentication during vehicle diagnostics, vehicle-to-grid and so on). The cybersecurity attacks targeting the global time result in false time, accuracy degradation, and denial of service as stated in IETF RFC 7384.

On the other hand, the potential risks associated with CAV deployment related to technical vulnerabilities are safety and cybersecurity issues that may arise from flawed hardware and software. Cybersecurity and Digital Trust Issues in Connected and Automated Vehicles elaborates on these topics as unsettled cybersecurity and digital trust issues in CAVs and follows with recommendations to fill in the gaps in this evolving field. ...Cybersecurity and Digital Trust Issues in Connected and Automated Vehicles elaborates on these topics as unsettled cybersecurity and digital trust issues in CAVs and follows with recommendations to fill in the gaps in this evolving field. ...This report also highlights the importance of establishing robust cybersecurity protocols and fostering digital trust in these vehicles to ensure safe and secure deployment in our modern transportation system.

It is essential to note that cybersecurity threats not only arise from inherent protocol defects but also consider software implementation vulnerabilities.

Since the early 1990’s, commercial vehicles have suffered from repeated vulnerability exploitations that resulted in a need for improved automotive cybersecurity. This paper outlines the strategies and challenges of implementing an automotive Zero Trust Architecture (ZTA) to secure intra-vehicle networks. ...This research successfully met the four requirements and demonstrated that using ZT principles in an on-vehicle network greatly improved the cybersecurity posture with manageable impact to system performance and deployment.

UNECE R155 explicitly references ISO/SAE 21434 and mandates a certified cybersecurity management system (CSMS) as a prerequisite for automotive manufacturers to achieve vehicle type approval and sell new vehicle types. ...However, the gap in the CSMS framework is a lack in a standardized system that provides guidance and common criteria for automakers to measure a vehicle’s level of compliance and compute a publicly accepted cybersecurity rating. To help establish increased consumer confidence, OEMs and smart mobility stakeholders could take additional proactive steps to ensure the safety and security of their products. ...This paper addresses the above requirement and discusses the cybersecurity rating framework (CSRF) that could establish a framework for rating vehicle cybersecurity by standardizing the measurement criteria, parameter vectors, process, and tools.

This paper gives a definition of the SDV concept, provides views from different aspects, discusses the progress in vehicle E/E architecture, especially zone-based architecture with centralized computation, and various technologies including High-Performance Computing (HPC) platform, standardized vehicle software architecture, advanced onboard communication, Over-The-Air (OTA) update, and cybersecurity etc. that collectively enable the realization of SDV.

The article also focus on innovative approaches that have recently adopted my many cybersecurity professionals for secured operation of ITS involving block-chain, artificial intelligence, and Machine Learning.

Advanced Autonomous Vehicles (AV) for SAE Level 3 and Level 4 functions will lead to a new understanding of the operation phase in the overall product lifecycle. Regulations such as the EU Implementing Act and the German L4 Act (AFGBV) request a continuous field surveillance, the handling of critical E/E faults and software updates during operation. This is required to enhance the Operational Design Domain (ODD) during operation, offering Functions on Demand (FoD), by increasing software features within these autonomous vehicle systems over the entire digital product lifecycle, and to avoid and reduce downtime by a malfunction of the Autonomous Driving (AD) software stack.

Access control enforces security policies for controlling critical resources. For V2X (Vehicle to Everything) autonomous military vehicle fleets, network middleware systems such as ROS (Robotic Operating System) expose system resources through networked publisher/subscriber and client/server paradigms. Without proper access control, these systems are vulnerable to attacks from compromised network nodes, which may perform data poisoning attacks, flood packets on a network, or attempt to gain lateral control of other resources. Access control for robotic middleware systems has been investigated in both ROS1 and ROS2. Still, these implementations do not have mechanisms for evaluating a policy's consistency and completeness or writing expressive policies for distributed fleets. We explore an RBAC (Role-Based Access Control) mechanism layered onto ROS environments that uses local permission caches with precomputed truth tables for fast policy evaluation.

Automotive system functionalities spread over a wide range of sub-domains ranging from non-driving related components to complex autonomous driving related components. The requirements to design and develop these components span across software, hardware, firmware, etc. elements. The successful development of these components to achieve the needs from the stockholders requires accurate understanding and traceability of the requirements of these component systems. The high-level customer requirements transformation into low level granularity requires an efficient requirement engineer. The manual understanding of the customer requirements from the requirement documents are influenced by the context and the knowledge gap of the requirement engineer in understanding and transforming the requirements.

The new generation vehicles these days are managed by networked controllers. A large portion of the networks is planned with more security which has recently roused researchers to exhibit various attacks against the system. This paper talks about the liabilities of the Controller Area Network (CAN) inside In-vehicle communication protocol and a few potentials that could take due advantage of it. Moreover, this paper presents a few security measures proposed in the present examination status to defeat the attacks. In any case, the fundamental objective of this paper is to feature a comprehensive methodology known as Intrusion Detection System (IDS), which has been a significant device in getting network data in systems over many years. To the best of our insight, there is no recorded writing on a through outline of IDS execution explicitly in the CAN transport network system.

Classic vehicle production had limitations in bringing the driving commands to the actuators for vehicle motion (engine, steering and braking). Steering columns, hydraulic tubes or steel cables needed to be placed between the driver and actuator. Change began with the introduction of e-gas systems. Mechanical cables were replaced by thin, electric signal wires. The technical solutions and legal standardizations for addressing the steering and braking systems, were not defined at this time. Today, OEMs are starting E/E-Architecture transformations for manifold reasons and now have the chance to remove the long hydraulic tubes for braking and the solid metal columns used for steering. X-by-wire is the way forward and allows for higher Autonomous Driving (AD) levels for automated driving vehicles. This offers new opportunities to design the vehicle in-cabin space. This paper will start with the introduction of x-by-wire technologies.

The separation of cybersecurity considerations in RMTO is barely considered, as so far, most available research and activities are mainly focused on AV. ...The main focus of this paper is addressing RMTO cybersecurity utilising an adaptable security-by-design approach, although security-by-design is still in the infant state within automotive cybersecurity. ...The main focus of this paper is addressing RMTO cybersecurity utilising an adaptable security-by-design approach, although security-by-design is still in the infant state within automotive cybersecurity. An adaptable security-by-design approach for RMTO covers Security Engineering Life-cycle, Logical Security Layered Concept, and Security Architecture.

Using a wireless medium for tractor-trailer communication will bring new cybersecurity challenges and requirements which requires new development and lifecycle considerations.

Additional complicating factors, such as cybersecurity concerns combined with a first responder’s legal authority, may pose challenges for traditional data collection.

CAN bus network proved to be efficient and dynamic for small compact cars as well as heavy-duty vehicles (HDV). However, HDVs are more susceptible to malicious attacks due to lack of security in their intra-vehicle communication protocols. SAE proposed a new standard named J1939-91C for CAN-FD networks which provides methods for establishing trust and securing mutual messages with optional encryption. J1939-91C ensures message authenticity, integrity, and confidentiality by implementing complex cryptographic operations including hash functions and random key generation. In this paper, the three main phases of J1939-91C, i.e., Network Formation, Rekeying, and Message Exchange, are simulated and tested on Electronic Control Units (ECUs) supporting CAN-FD network. Numerous test vectors were generated and validated to support SAE J1939-91C. The mentioned vectors were produced by simulating different encryption and hashing algorithms with variable message and key lengths.

Cybersecurity (CS) is crucial and significantly important in every product that is connected to the network/internet. ...Hence making it very important to guarantee that every single connected device shall have cybersecurity measures implemented to ensure the safety of the entire system. Looking into the forecasted worldwide growth in the electric vehicles (EV’s) segment, CS researchers have recently identified several vulnerabilities that exist in EV’s, electric vehicle supply equipment (EVSE) devices, communications to EVs, and upstream services, such as EVSE vendor cloud services, third party systems, and grid operators. ...Additional processes have been defined in the process reference and assessment model for the CS engineering in order to incorporate the cybersecurity related processes in the ASPICE scope. This paper aims at providing a model & brief overview to establish a correlation between the ASPICE, ISO/SAE 21434 and the ISO 26262 functional safety (FS) standards for development of a secured cybersecurity software with all the considerations that an organization can undertake.

By looking into the vehicle-infrastructure cooperation (VIC) which is oriented towards intelligent, networked and integrated development, this paper analyzes and proposes the essence and development direction of Intelligent Vehicle Infrastructure Cooperation Systems (I-VICS). With an in-depth analysis of technologies of core importance to VIC and influence factors that constrain VIC development as a whole, the paper comes up with a technological route for VIC, and identifies a direction for vehicle-infrastructure cooperative development that progresses from primary to intermediate cooperation, then to advanced cooperation, and finally to full-fledged cooperation. Policy recommendations aiming at strengthening top-level design, building an integrated vehicle-infrastructure-cloud platform, expediting independence of key techs, building robust standards and regulations for VIC, enhancing workforce development as well as greater efforts at market promotion are put forward.

Facial recognition software (FRS) is a form of biometric security that detects a face, analyzes it, converts it to data, and then matches it with images in a database. This technology is currently being used in vehicles for safety and convenience features, such as detecting driver fatigue, ensuring ride share drivers are wearing a face covering, or unlocking the vehicle. Public transportation hubs can also use FRS to identify missing persons, intercept domestic terrorism, deter theft, and achieve other security initiatives. However, biometric data is sensitive and there are numerous remaining questions about how to implement and regulate FRS in a way that maximizes its safety and security potential while simultaneously ensuring individual’s right to privacy, data security, and technology-based equality.

With the rapid development of connected and autonomous vehicles, more sophisticated automotive systems running large portions of software and implementing a variety of communication interfaces are being developed. The ever-expanding codebase increases the risk for software vulnerabilities, while at the same time the large number of communication interfaces make the systems more susceptible to be targeted by attackers. As such, it is of utmost importance for automotive organizations to identify potential vulnerabilities early and continuously in the development lifecycle in an automated manner. In this paper, we suggest a practical approach for integrating fuzz testing into a Continuous Integration (CI) pipeline for automotive systems. As a first step, we have performed a Threat Analysis and Risk Assessment (TARA) of a general E/E architecture to identify high-risk interfaces and functions.