Search Results

The introduction of this model eliminated prior limitations that PC-Crash had for simulating motorcycle motion. Within PC-Crash, a user-defined path can be established for a motorcycle, and the software will generate motion consistent with the user-defined path (within the limits of friction and stability) and calculate the motorcycle lean (roll) generated by following that path at the prescribed speed, braking, or acceleration levels. ...However, the model again did not utilize counter-steering to generate lean, and so it is unlikely that the steering inputs generated by PC-Crash would match the real-world steering inputs. Still, the PC-Crash single-track driver model will yield results that are typically adequate for a crash reconstruction or visualization. ...This paper validates the single-track vehicle driver model available in PC-Crash simulation software. The model is tested, and its limitations are described. The introduction of this model eliminated prior limitations that PC-Crash had for simulating motorcycle motion.

First, the roundabout driving safety evaluation based on the rollover propensity index calculated with the tire loads was performed through various PC-Crash simulation analysis. And, using the Taguchi method, which is a representative DOE method, major factors affecting the rollover index were set by type and the sensitivity analysis results were quantitatively obtained.

Parameters such as vehicle weight, sliding friction factor, motorcycle sliding trajectory, and yaw trajectory will be accounted for in each PC-Crash simulation. All tests were simulated using a 2D and 3D motorcycle model in PC-Crash. Additionally, calculated averaged slide-to-stop decelerations and slide-to-stop distances based on physical evidence were used and verified in the PC-Crash simulation. ...PC-Crash is an accident reconstruction program that enables the user to analyze vehicle collision dynamics and trajectory models. ...This research paper presents the utilization of PC-Crash to analyze motorcycle slide-to-stop dynamics. For this study, existing motorcycle slide-to-stop data from SAE 2019-01-0426 will be simulated and analyzed in PC-Crash.

The most general and comprehensive solution will be to use one of the widely-accepted accident reconstruction simulation programs - PC-Crash, HVE (the EDSMAC4 or SIMON modules), Virtual CRASH, or VCRware. However, these simulation programs can be time-consuming to apply and not everyone has access to them.

The software packages included in the studies presented in this paper are HVE (SIMON and EDSMAC4), PC-Crash and VCRware. This paper will present the results of the study, conducted using DOE, involving these models.

PC-Crash is a vehicular accident simulation software that is widely used by the accident reconstruction community. ...The goal of this article is to review the prior literature that has addressed the capabilities of PC-Crash and its accuracy and reliability for various applications (planar collisions, rollovers, and human motion). ...In addition, this article aims to add additional analysis of the capabilities of PC-Crash for simulating planar collisions and rollovers. Simulation analysis of five planar collisions originally reported and analyzed by Bailey [2000] are reexamined.

Each accident in this sample is modeled numerically by the simulation tool PC-Crash. In parallel, a model representing the function of an AEB system has been established.

Using the PCM philosophy and including 5 seconds before the accident in the crash analysis combined with the driving behaviours of the vehicles out of PC-Crash, it is possible to analyse, whether or not a sensor system would have been able to recognise the dangerous situation in time to avoid or mitigate the accident.

Furthermore, 183car-to-pedestrian cases, with detailed information regarding accident vehicles, pedestrians and environment, were reconstructed using PC-Crash. A hypothetical autonomous braking system would activate when the pedestrian successfully detected by the sensing system and then new impact speeds will be calculated.

Reconstruction by PC-Crash was performed for all of the sampled cases. Pre-crash parameters were calculated by a MATLAB code.

The research reported here offers a validation of this capability, demonstrating that PC-Crash can be used to realistically model the build-up of a vehicle's speed under maximal acceleration. ...In the research reported here, PC-Crash 9.0 was used to model the full-throttle acceleration capabilities of three vehicles with automatic transmissions - a 2006 Ford Crown Victoria Police Interceptor (CVPI), a 2000 Cadillac DeVille DTS, and a 2003 Ford F150. ...In each case, the full-throttle acceleration of the vehicles modeled in PC-Crash showed good agreement with the acceleration of the real vehicles in our road tests.

Next, simulations in PC-Crash were performed, and the results were compared with those obtained in experiments.

PC-Crash simulations of staged collisions require dozens of parameters describing vehicle and impact parameters.

The vehicle dynamics of all scenarios from the database will be simulated in PC-Crash, an accident-reconstruction software. Since the brake assist is obligatory from 2012 on, the system and its effect on each single accident scenario will be modeled.

Lateral acceleration, roll angle, roll rate, and yaw rate vehicle response from PC-Crash were compared to the MSAI sensor data. The authors modeled 26 handling tests. PC-Crash appeared to be a reasonable tool for modeling gross vehicle response. ...This research compares vehicle dynamic simulations in PC-Crash 8.2 to data recorded during instrumented handling tests conducted by Mechanical Systems Analysis Incorporated (MSAI). ...Vehicle weight, center of gravity (c.g) position, suspension stiffness parameters, tire parameters, steering angle, and vehicle speed data provided by MSAI were used as input for the PC-Crash model. Lateral acceleration, roll angle, roll rate, and yaw rate vehicle response from PC-Crash were compared to the MSAI sensor data.

The objective of the paper is to present the results of verification of ABS models applied in PC-Crash and HVE (Human-Vehicle-Environment) computer programs in various road conditions. The aim was reached by comparison of the road tests results obtained and calculations performed using the programs for the same initial values of the measured variables.

All of them are analysed in-depth and reconstructed with PC-Crash. The effects of the frontal structure of the vehicles and several active systems, such as BAS and Pedestrian Detection Systems, are evaluated. ...The paper includes the description of the methodology followed for a sample of approximately 140 pedestrian urban accidents in three cities in Spain (Madrid, Barcelona and Zaragoza) and the corresponding reconstructions done with PC-Crash. Then, a methodology to simulate the passive and active improvements (including pedestrian friendly structure, BAS and pedestrian detection system) is defined and applied to all the sampled accidents.

The current capabilities of PC-Crash for rollover modeling are discussed and suggestions are made for how PC-Crash might be improved for modeling rollovers. ...This paper evaluates the use of PC-Crash simulation software for modeling the dynamics of a dolly rollover crash test. The specific test used for this research utilized a Ford sport utility vehicle and was run in accordance with SAE J2114. ...Next, the test was modeled using PC-Crash. The simulation was optimized to yield a reasonable fit with the actual test dynamics by changing the following parameters in PC-Crash: (1) the friction coefficient associated with each vehicle-to-ground impact; (2) the coefficient of restitution for vehicle-to-ground impacts; (3) the vehicle body stiffness; and (4) the vehicle suspension and damping.

In this work, we focused on the trip-over type, which occurs most frequently, and performed simulations to reproduce real-world rollover accidents by combining PC-Crash and FEA. Soil trip-over simulation was carried out based on real world accidents. Based on rigid body dynamics, PC-Crash software was chosen to make an accident reconstruction analysis of some selected cases chosen from an accident database (NASS-CDS). ...Based on rigid body dynamics, PC-Crash software was chosen to make an accident reconstruction analysis of some selected cases chosen from an accident database (NASS-CDS). ...The output of this PC-crash simulation was then used as the initial input conditions (i.e., speed, deceleration, etc.) of a detailed finite element analysis.

In this work, we focused on the trip-over type, which occurs most frequently, and performed simulations to reproduce real-world rollover accidents by combining PC-Crash and FEA. At first, using a simplified full car model, sufficient conditions, such as additional velocity, required for a curb trip-over accident to occur, were derived from energy balance concept based on the same principle as critical sliding velocity (CSV) criterion. ...Based on rigid body dynamics, PC-Crash software was chosen to make an accident reconstruction analysis of some selected cases chosen from an accident database (NASS-CDS). ...The output of this PC-crash simulation was then used as the initial input conditions (i.e., speed, deceleration, etc.) of a detailed finite element analysis.