Search Results

The program PC-CRASH was developed for the reconstruction of vehicle accidents and considers pre-impact, collision and post-impact phases. ...The present paper describes the physical and mathematical model which was added recently to PC-CRASH in order to enable the simulation of the dynamic behavior of articulated vehicles (with both single and double axle semi-trailers and with steered trailers).

Parameters such as vehicle weight, sliding friction factor, motorcycle sliding trajectory, and yaw trajectory will be accounted for in each PC-Crash simulation. All tests were simulated using a 2D and 3D motorcycle model in PC-Crash. Additionally, calculated averaged slide-to-stop decelerations and slide-to-stop distances based on physical evidence were used and verified in the PC-Crash simulation. ...PC-Crash is an accident reconstruction program that enables the user to analyze vehicle collision dynamics and trajectory models. ...This research paper presents the utilization of PC-Crash to analyze motorcycle slide-to-stop dynamics. For this study, existing motorcycle slide-to-stop data from SAE 2019-01-0426 will be simulated and analyzed in PC-Crash.

PC-Crash is a Windows™ - based accident reconstruction program developed in Graz, Austria by Dr. Hermann Steffan. ...Hermann Steffan. PC-Crash collision analysis results are compared with previously published staged collision data. ...The staged collisions were reconstructed using PC-Crash and the trajectories were compared to actual measurements of the skid marks and rest positions.

PC-Crash is an accident reconstruction program allowing the user to perform simulations with multibody objects that collide or interact with 3D vehicle mesh models. ...The current motorcycle models in PC-Crash are generic and do not resemble a sport bike type motorcycle. They are only globally scalable such that you cannot adjust length, width, or height independently. ...The test results were compared to parameters calculated in PC-Crash. Results such as Delta-V, yaw rate and overall post impact trajectories of the motorcycle, rider and movement of the target vehicle were compared to the data from the instrumented test vehicles.

The introduction of this model eliminated prior limitations that PC-Crash had for simulating motorcycle motion. Within PC-Crash, a user-defined path can be established for a motorcycle, and the software will generate motion consistent with the user-defined path (within the limits of friction and stability) and calculate the motorcycle lean (roll) generated by following that path at the prescribed speed, braking, or acceleration levels. ...However, the model again did not utilize counter-steering to generate lean, and so it is unlikely that the steering inputs generated by PC-Crash would match the real-world steering inputs. Still, the PC-Crash single-track driver model will yield results that are typically adequate for a crash reconstruction or visualization. ...This paper validates the single-track vehicle driver model available in PC-Crash simulation software. The model is tested, and its limitations are described. The introduction of this model eliminated prior limitations that PC-Crash had for simulating motorcycle motion.

Five collisions were staged in order to evaluate PC-Crash, a simulation program used for investigating motor vehicle collisions. Both vehicles were moving in all of the staged collisions at 1:1 or 2:1 speed ratios. ...Firstly, collision parameters were calculated from measured data, and used as input to the PC-Crash collision model. Secondly, the post-impact vehicle paths and rest positions were used to determine the pre-impact speeds. ...Using the PC-Crash "Optimizer" to reconstruct the five collisions, the error in calculated pre-impact speeds of the ten vehicles ranged from-3.3 to +4.1 km/h.

Next, simulations in PC-Crash were performed, and the results were compared with those obtained in experiments.

PC-Crash simulations of staged collisions require dozens of parameters describing vehicle and impact parameters.

First, the roundabout driving safety evaluation based on the rollover propensity index calculated with the tire loads was performed through various PC-Crash simulation analysis. And, using the Taguchi method, which is a representative DOE method, major factors affecting the rollover index were set by type and the sensitivity analysis results were quantitatively obtained.

These predictions were generated by directly integrating the VCH data and by using the VCH data as inputs to PC-Crash simulations. The predicted positions and headings were then compared to the actual position and heading data measured using differential GPS synchronized to the VCH data record.

The most general and comprehensive solution will be to use one of the widely-accepted accident reconstruction simulation programs - PC-Crash, HVE (the EDSMAC4 or SIMON modules), Virtual CRASH, or VCRware. However, these simulation programs can be time-consuming to apply and not everyone has access to them.

Furthermore, 183car-to-pedestrian cases, with detailed information regarding accident vehicles, pedestrians and environment, were reconstructed using PC-Crash. A hypothetical autonomous braking system would activate when the pedestrian successfully detected by the sensing system and then new impact speeds will be calculated.

Development of crash avoidance systems and active safety systems must not be only based on experimental knowledge. The goal is to provide an efficient answer to still unsolved severe real-world car crashes which occur despite enhanced passive safety devices. This requires to know precisely the pre-crash conditions during about 3 to 10 seconds before impact. The paper describes the multidisciplinary systemic approach leading to the comprehensive methodology used in accident reconstruction in order to determine the best scenario, and to assess initial car speeds, paths and events in the different phases of the accident. This has already been carried out for about 400 car crashes with car occupant injuries (including 6% fatal and 10% severely injured). The necessity of collecting data on the spot of the crash scene is highlighted. Three well-trained investigators are involved.