Search Results

Lateral acceleration, roll angle, roll rate, and yaw rate vehicle response from PC-Crash were compared to the MSAI sensor data. The authors modeled 26 handling tests. PC-Crash appeared to be a reasonable tool for modeling gross vehicle response. ...This research compares vehicle dynamic simulations in PC-Crash 8.2 to data recorded during instrumented handling tests conducted by Mechanical Systems Analysis Incorporated (MSAI). ...Vehicle weight, center of gravity (c.g) position, suspension stiffness parameters, tire parameters, steering angle, and vehicle speed data provided by MSAI were used as input for the PC-Crash model. Lateral acceleration, roll angle, roll rate, and yaw rate vehicle response from PC-Crash were compared to the MSAI sensor data.

During recent years the accident simulation program PC-Crash was developed. This software simulates vehicle movement before, during and after the impact, using 3D vehicle and scene models. ...A new interface has been developed between MADYMO® and PC-Crash so that, after the reconstruction of an accident, only a few additional parameters regarding restraint system, seat and occupant must be defined. ...A new interface has been developed between MADYMO® and PC-Crash so that, after the reconstruction of an accident, only a few additional parameters regarding restraint system, seat and occupant must be defined. PC-Crash then creates all necessary input files for MADYMO® and starts the occupant simulation.

PC-Crash is a vehicular accident simulation software that is widely used by the accident reconstruction community. ...The goal of this article is to review the prior literature that has addressed the capabilities of PC-Crash and its accuracy and reliability for various applications (planar collisions, rollovers, and human motion). ...In addition, this article aims to add additional analysis of the capabilities of PC-Crash for simulating planar collisions and rollovers. Simulation analysis of five planar collisions originally reported and analyzed by Bailey [2000] are reexamined.

The most general and comprehensive solution will be to use one of the widely-accepted accident reconstruction simulation programs - PC-Crash, HVE (the EDSMAC4 or SIMON modules), Virtual CRASH, or VCRware. However, these simulation programs can be time-consuming to apply and not everyone has access to them.

The current capabilities of PC-Crash for rollover modeling are discussed and suggestions are made for how PC-Crash might be improved for modeling rollovers. ...This paper evaluates the use of PC-Crash simulation software for modeling the dynamics of a dolly rollover crash test. The specific test used for this research utilized a Ford sport utility vehicle and was run in accordance with SAE J2114. ...Next, the test was modeled using PC-Crash. The simulation was optimized to yield a reasonable fit with the actual test dynamics by changing the following parameters in PC-Crash: (1) the friction coefficient associated with each vehicle-to-ground impact; (2) the coefficient of restitution for vehicle-to-ground impacts; (3) the vehicle body stiffness; and (4) the vehicle suspension and damping.

During recent years the accident simulation program PC-CRASH was developed, which allows simulating the vehicles movement before, during and after the impact. ...The first one serves as an alternative for the optimizer tool and is included in the current version of PC-Crash. It gives reasonable insight in the variation of certain parameters in reasonable calculation time.

For the current paper the simulation models of PC-Crash [1], [2], [3] were used. In the last part of the paper several sample cases from crash tests and real life accidents are presented together with the result of the automatic optimization process.

Automotive occupant safety continues to evolve. At present this area has gathered a strong consumer interest which the vehicle manufacturers are tapping into with the introduction of many new safety technologies. Initially, individual passive devices and features such as seatbelts, knee- bolsters, structural crush zones, airbags etc., were developed for to help save lives and minimize injuries in accidents. Over the years, preventive measures such as improving visibility, headlights, windshield wipers, tire traction etc., were deployed to help reduce the probability of getting into an accident. With tremendous new research and improvements in electronics, we are at the stage of helping to actively avoid accidents in certain situations as well as providing increased protection to vehicle occupants and pedestrians.

Five collisions were staged in order to evaluate PC-Crash, a simulation program used for investigating motor vehicle collisions. Both vehicles were moving in all of the staged collisions at 1:1 or 2:1 speed ratios. ...Firstly, collision parameters were calculated from measured data, and used as input to the PC-Crash collision model. Secondly, the post-impact vehicle paths and rest positions were used to determine the pre-impact speeds. ...Using the PC-Crash "Optimizer" to reconstruct the five collisions, the error in calculated pre-impact speeds of the ten vehicles ranged from-3.3 to +4.1 km/h.

All of them are analysed in-depth and reconstructed with PC-Crash. The effects of the frontal structure of the vehicles and several active systems, such as BAS and Pedestrian Detection Systems, are evaluated. ...The paper includes the description of the methodology followed for a sample of approximately 140 pedestrian urban accidents in three cities in Spain (Madrid, Barcelona and Zaragoza) and the corresponding reconstructions done with PC-Crash. Then, a methodology to simulate the passive and active improvements (including pedestrian friendly structure, BAS and pedestrian detection system) is defined and applied to all the sampled accidents.

In this work, we focused on the trip-over type, which occurs most frequently, and performed simulations to reproduce real-world rollover accidents by combining PC-Crash and FEA. At first, using a simplified full car model, sufficient conditions, such as additional velocity, required for a curb trip-over accident to occur, were derived from energy balance concept based on the same principle as critical sliding velocity (CSV) criterion. ...Based on rigid body dynamics, PC-Crash software was chosen to make an accident reconstruction analysis of some selected cases chosen from an accident database (NASS-CDS). ...The output of this PC-crash simulation was then used as the initial input conditions (i.e., speed, deceleration, etc.) of a detailed finite element analysis.

The vehicle dynamics of all scenarios from the database will be simulated in PC-Crash, an accident-reconstruction software. Since the brake assist is obligatory from 2012 on, the system and its effect on each single accident scenario will be modeled.

This study focuses on one program, PC-CRASH. This program was developed to allow simulations of vehicle 3-dimensional movements before, during and after the impact.

Next, simulations in PC-Crash were performed, and the results were compared with those obtained in experiments.

The analyst may often turn to accident reconstruction software such as the various versions of SMAC and some impulse-momentum approaches like PC-Crash and VCRware. Within these programs there is a user-input variable often referred to as the inter-vehicle friction coefficient.

HVE 1 and PC-Crash 2 have been the subject of numerous SAE papers. Both programs have been offered to reconstructionists for the purpose of analyzing vehicle accidents and presenting the resulting motions in 3D graphical form.

Sensor signals are derived using the PC-Crash tool, and characteristic features are identified. Insights derived from these events can aid in development of robust rollover detection algorithms and calibrations.

An optimizer tool in PC-Crash is designed to minimize reconstruction time and error by automatically varying a selected number of impact parameters, comparing the resulting simulation for each combination of parameters with the actual incident. ...Twenty staged collisions were reconstructed with the optimizer tool in PC-Crash. These staged collisions had been previously reconstructed with a combination of manual linear momentum calculations combined with the trajectory model in an earlier version of PC-Crash. ...These staged collisions had been previously reconstructed with a combination of manual linear momentum calculations combined with the trajectory model in an earlier version of PC-Crash. Differences between the reconstruction simulations and the actual collisions, and methods for minimizing reconstruction errors, are discussed.

First, the roundabout driving safety evaluation based on the rollover propensity index calculated with the tire loads was performed through various PC-Crash simulation analysis. And, using the Taguchi method, which is a representative DOE method, major factors affecting the rollover index were set by type and the sensitivity analysis results were quantitatively obtained.

The software packages included in the studies presented in this paper are HVE (SIMON and EDSMAC4), PC-Crash and VCRware. This paper will present the results of the study, conducted using DOE, involving these models.