Search Results

During recent years the accident simulation program PC-Crash was developed. This software simulates vehicle movement before, during and after the impact, using 3D vehicle and scene models. ...A new interface has been developed between MADYMO® and PC-Crash so that, after the reconstruction of an accident, only a few additional parameters regarding restraint system, seat and occupant must be defined. ...A new interface has been developed between MADYMO® and PC-Crash so that, after the reconstruction of an accident, only a few additional parameters regarding restraint system, seat and occupant must be defined. PC-Crash then creates all necessary input files for MADYMO® and starts the occupant simulation.

The most general and comprehensive solution will be to use one of the widely-accepted accident reconstruction simulation programs - PC-Crash, HVE (the EDSMAC4 or SIMON modules), Virtual CRASH, or VCRware. However, these simulation programs can be time-consuming to apply and not everyone has access to them.

This study focuses on one program, PC-CRASH. This program was developed to allow simulations of vehicle 3-dimensional movements before, during and after the impact.

First, the roundabout driving safety evaluation based on the rollover propensity index calculated with the tire loads was performed through various PC-Crash simulation analysis. And, using the Taguchi method, which is a representative DOE method, major factors affecting the rollover index were set by type and the sensitivity analysis results were quantitatively obtained.

This paper presents the trajectory and collision models on which PC-CRASH is based. PC-CRASH'S model for predicting the 3D kinematics of a vehicle's pre- and post-impact trajectory, which is based on a discrete- kinetic time forward simulation of vehicle dynamics rather than empirically-derived “spin-out coefficients”, is described. ...PC-CRASH is a windowso-based accident-reconstruction program which combines the simulation of pre-collision, collision, and post-collision dynamics for multiple vehicles in a graphical environment.

The program PC-CRASH was developed for the reconstruction of vehicle accidents and considers pre-impact, collision and post-impact phases. ...The present paper describes the physical and mathematical model which was added recently to PC-CRASH in order to enable the simulation of the dynamic behavior of articulated vehicles (with both single and double axle semi-trailers and with steered trailers).

Furthermore, 183car-to-pedestrian cases, with detailed information regarding accident vehicles, pedestrians and environment, were reconstructed using PC-Crash. A hypothetical autonomous braking system would activate when the pedestrian successfully detected by the sensing system and then new impact speeds will be calculated.

Parameters such as vehicle weight, sliding friction factor, motorcycle sliding trajectory, and yaw trajectory will be accounted for in each PC-Crash simulation. All tests were simulated using a 2D and 3D motorcycle model in PC-Crash. Additionally, calculated averaged slide-to-stop decelerations and slide-to-stop distances based on physical evidence were used and verified in the PC-Crash simulation. ...PC-Crash is an accident reconstruction program that enables the user to analyze vehicle collision dynamics and trajectory models. ...This research paper presents the utilization of PC-Crash to analyze motorcycle slide-to-stop dynamics. For this study, existing motorcycle slide-to-stop data from SAE 2019-01-0426 will be simulated and analyzed in PC-Crash.

PC-Crash is an accident reconstruction program allowing the user to perform simulations with multibody objects that collide or interact with 3D vehicle mesh models. ...The current motorcycle models in PC-Crash are generic and do not resemble a sport bike type motorcycle. They are only globally scalable such that you cannot adjust length, width, or height independently. ...The test results were compared to parameters calculated in PC-Crash. Results such as Delta-V, yaw rate and overall post impact trajectories of the motorcycle, rider and movement of the target vehicle were compared to the data from the instrumented test vehicles.

The introduction of this model eliminated prior limitations that PC-Crash had for simulating motorcycle motion. Within PC-Crash, a user-defined path can be established for a motorcycle, and the software will generate motion consistent with the user-defined path (within the limits of friction and stability) and calculate the motorcycle lean (roll) generated by following that path at the prescribed speed, braking, or acceleration levels. ...However, the model again did not utilize counter-steering to generate lean, and so it is unlikely that the steering inputs generated by PC-Crash would match the real-world steering inputs. Still, the PC-Crash single-track driver model will yield results that are typically adequate for a crash reconstruction or visualization. ...This paper validates the single-track vehicle driver model available in PC-Crash simulation software. The model is tested, and its limitations are described. The introduction of this model eliminated prior limitations that PC-Crash had for simulating motorcycle motion.