Search Results

This is an extension of simple fuel consumption modeling toward HEV. Previous work showed that in urban driving the overhead of running an ICEV engine can use as much fuel as the traction work. The bidirectional character and high efficiency of electric motors enables HEVs to run as a BEV at negative and low traction powers, with no net input from the small battery. The ICE provides the net work at higher traction powers where it is most efficient. Whereas the network reduction is the total negative work times the system round-trip efficiency, the reduction in engine running time requires knowledge of the distribution of traction power levels. The traction power histogram, and the work histogram derived from it, provide the required drive cycle description. The traction power is normalized by vehicle mass, so that the drive trace component becomes invariant, and the road load component nearly invariant to vehicle mass.

Lithium-ion batteries (LIBs) have been used as the main power source for Electric vehicles (EVs) in recent years. The mechanical behavior of LIBs subject to crush loading is crucial in assessing and improving the impact safety of battery systems and EVs. In this work, a detailed 3D finite element model for a commercial vehicle battery was built, in order to better understand battery failure behavior under various loading conditions. The model included the major components of a prismatic battery jellyroll, i.e., cathodes, anodes, and separators. The models for these components were validated against the corresponding material coupon tests (e.g., tension and compression). Then the components were integrated into the cell level model for simulation of jellyroll loading and damage behavior under three types of compressive indenter loading: (1) Flat-end punch, (2) Hemispherical punch and (3) Round-edge wedge. The comparisons showed reasonable agreement between modeling and experiments.

Electric vehicles (EVs) are a promising and proven technology for achieving sustainable mobility with zero carbon emissions, very low noise pollution, and reducing the dependency on fossil fuels. Global EV sales have been increasing by ~110 % since 2015, with a significant rise in 2021 (~6.75 mils EV registered) mainly led by China, the US, and Europe, amplifying the EV market share to 8.3% compared to 4.2% in 2020. Future developments aimed at designing better batteries and charging technologies that reduce charging time, reduce initial battery cost, and increased flexibility. In India, EVs are emerging significantly due to stringent Carbon di Oxide (CO2) reduction drives, increasing crude oil prices, and the availability of cheaper renewable energy. Leveraging government promotional policies, evolving the entire ecosystem, globally advantageous manufacturing costs, and competitive engineering skills form the perfect blend for India.

The Composite Hybrid Automotive Suspension System Innovative Structures (CHASSIS) is a project that developed structural commercial vehicle suspension components in high volume utilising hybrid materials and joining techniques to offer a viable lightweight production alternative to steel. Three components were selected for the project:- Front Subframe Front Lower Control Arm (FLCA) Rear Deadbeam Axle

The previously developed power-based fuel consumption theory for Internal Combustion Engine Vehicles (ICEV) is extended to Battery Electric Vehicles (BEV). The main difference between the BEV model structure and the ICEV is the bi-directional character of traction motors and batteries. A traction motor model was developed as a bi-linear function of positive and negative traction power. Another difference is that the accessories and cabin heating are powered directly from the battery, and not from the powertrain. The resulting unified model for ICEV and BEV energy consumption has linear terms proportional to positive and negative traction power, accessory power, and overhead, in varying proportions. Compared to the ICEV, the BEV powertrain has a high marginal efficiency and low overhead. As a result, BEV energy consumption data under a wide range of driving conditions are mainly proportional to net traction power, with only a small offset.

As electric vehicles are becoming increasingly popular and necessary for the future mobility needs of civilization, further effort is continually made to improve the efficiency, cost, and safety of the lithium-ion battery packs that power these vehicles. To facilitate these goals, this paper introduces a data driven model to predict a distribution of surface temperatures for a lithium-ion battery pack: a long short-term memory (LSTM) neural network. The LSTM model is trained and validated with lithium-ion cells electrically connected to form a battery pack. Voltage, current, state of charge (SOC), and cell surface temperature from two arrays are used as inputs from a wide range of high and low temperature drive cycles. Additionally, ambient temperature is added as an input to the LSTM model.

This article aims to analyze the potential economic effects for consumers with the implementation of the Vehicle-to-Grid (V2G) and the Vehicle-to-Home (V2H) networks in Brazil. Nowdays, the usage of both technologies in Brazil are at a regulatory vacuum for both Battery Electric Vehicles (BEVs), Plug-in Hybrid Electric Vehicles (PHEVs) and Hybrid Electric Vehicles (HEVs). Usually, when a legislation lack occurs, the local OEMs adopt IECs (International Electrotechnical Commissions) and/or SAEs (Society of Automotive Engineers) reference international standards, such as SAE J1634 for range test.

Electrochemical models of lithium ion batteries are today a standard tool in the automotive industry for activities related to the computer-aided engineering design, analysis, and optimization of energy storage systems for electrified vehicles. One of the challenges in the development or use of such models is the need of detailed information on the cell and electrode geometry or properties of the electrode and electrolyte materials, which are typically unavailable or difficult to retrieve by end-users. This forces engineers to resort to “hand-tuning” of many physical and geometrical parameters, using standard cell-level characterization tests. This paper proposes a method to provide information and data on individual electrode performance that can be used to simplify the calibration process for electrochemical models.

The Composite Hybrid Automotive Suspension System Innovative Structures (CHASSIS) is a project to develop structural commercial vehicle suspension components in high volume utilising hybrid materials and joining techniques to offer a viable lightweight production alternative to steel. Three components are in scope for the project:- Front Subframe Front Lower Control Arm (FLCA) Rear Deadbeam Axle

Given continued industry focus on reducing parasitic losses, the ability to accurately measure the magnitude of losses on all driveline components is required. A standardized test procedure enables manufacturers and suppliers to measure component losses consistently, in addition to offering a reliable process to assess enablers for efficiency improvements. This paper reviews the development of SAE draft standard J3218, which is a comprehensive test procedure to break-in and characterize the efficiency of beam axles. Focus areas of the study included ensuring the axle’s efficiency does not change as it is being characterized, building a detailed map of efficiency at a wide range of operating points, and minimizing test time. The resulting break-in procedure uses an asymptotic regression approach to predict fully broken in efficiency of the axle and determine how much the efficiency of the axle changes during the characterization phase.

There are a variety of test protocols associated with vehicle fuel economy and emissions testing. As a result, a number of test protocols currently exist to measure axle efficiency and spin loss. The intent of this technical paper is to describe a methodology that uses a singular axle efficiency and spin loss procedure. The data can then be used to predict the effects on vehicle FE and GHG for a specific class of vehicles via simulation. An accelerated break-in method using a comparable energy approach has been developed, and can be used to meet the break-in requirements of different vehicle emission test protocols. A “float to equilibrium” sump temperature approach has been used to produce instantaneous efficiency data, which can be used to more accurately predict vehicle FE and GHG, inclusive of Cold CO2. The “Float to Equilibrium” approach and “Fixed Sump Temperature” approach has been compared and discussed.

This paper describes development of an integrated regenerative braking system and anti-lock brake system (ABS) control during an ABS event for hybrid and electric vehicles with drivelines containing a single electric motor connected to the axle shaft through an open differential. The control objectives are to recuperate the maximum amount of kinetic energy during an ABS event, and to provide no degraded anti-lock control behavior as seen in vehicles with regenerative braking disabled. The paper first presents a detailed control system analysis to reveal the inherent property of non-zero regenerative braking torque control during ABS event and explain the reason why regenerative braking torque can increase the wheel slip during ABS event with existing regenerative braking control strategies.

Real-world second-by-second vehicle driving cycle data is very important for vehicle research and development. A project solely dedicated to generating such information would be tremendously costly and time consuming. Alternatively, we developed such a database by utilizing two publicly available passenger vehicle travel surveys: 2004-2006 Puget Sound Regional Council (PSRC) Travel Survey and 2011 Atlanta Regional Commission (ARC) Travel Survey. The surveys complement each other - the former is in low time resolution but covers driver operation for over one year whereas the latter is in high time resolution but represents only one-week-long driving operation. After analyzing the PSRC survey, we chose 382 vehicles, each of which continuously operated for one year, and matched their trips to all the ARC trips. The matching is carried out based on trip distance first, then on average speed, and finally on duration.

The new European test procedure, called the worldwide harmonized light vehicle test procedure (WLTP), deviates in some details from the current NEDC-based test which will have an impact on the determination of the official EU fuel consumption values for the new vehicles. The adaptation to the WLTP faces automakers with new challenges for meeting the stringent EU fuel consumption and CO2 emissions standards. This paper investigates the main changes that the new test implies to a mid-size sedan electrified vehicle design and quantifies their impact on the vehicles fuel economy. Three common electrified powertrain architectures including series, parallel P2, and powersplit are studied. A Pontryagin’s Minimum Principle (PMP) optimization-based energy management control strategy is developed to evaluate the energy consumption of the electrified vehicles in both charge-depleting (CD) and charge-sustaining (CS) modes.

Due to the increasing concerns on energy and environmental issues, the automotive industry has seen increased growth and development of electric and electrified vehicles [1]. The power-split design is one of the most common drivetrain configurations of a hybrid or electrified vehicle. The propulsion system of a power-split hybrid vehicle typically comprises of an engine drive system in which the engine, drivetrain and generator are mechanically coupled on a planetary gear set driveline while the electric drive system consists of a high voltage battery and a traction motor [2]. In recent years, Hardware-in-the-Loop (HIL) simulation has become an increasingly common approach for controls rapid prototyping and validation as part of the automotive product development cycle [2, 3].

Plug-in hybrid (PHEV) technology offers the ability to achieve zero tailpipe emissions coupled with convenient refueling. Fleet adoption of PHEVs, often motivated by organizational and regulatory sustainability targets, may not always align with optimal use cases. In a car rental application, barriers to improving fuel economy over a conventional hybrid include: diminished benefits of additional battery capacity on long-distance trips, sparse electric charging infrastructure at the fleet location, lack of renter understanding of electric charging options, and a principle-agent problem where the driver accrues fewer benefits than costs for actions that improve fuel economy, like charging and eco-driving. This study uses high-resolution driving data collected from twelve Ford Fusion Energi sedans owned by University of California, Davis (UC Davis), where the vehicles are rented out for university-related activities.

The initiative of this paper is focused on improving the heat dissipation from the pressure wheel of a laser welding assembly in order to achieve a longer period of use. The work examines the effects of different geometrical designs on the thermal performance of pressure wheel assembly during a period of cooling time. Three disc designs were manufactured for testing: Design 1 – a plain wheel, Design 2 – a pierced wheel, and Design 3 – a wheel with ventilating vanes. All of the wheels were made of carbon steel. The transient thermal reaction were compared. The experimental results indicate that the ventilated wheel cools down faster with the convection in the ventilated channels, while the solid plain wheel continues to possess higher temperatures. A comparison among the three different designs indicates that the Design 3 has the best cooling performance.

There has been a general consensus in the scientific literature that a rim gouging, not scraping, into a roadway surface generates very high forces which can cause a vehicle to overturn in some situations. However, a paper published in 2004 attempts to minimize the forces created during wheel rim gouging and the effect on vehicle rollover. This paper relied largely on heavily filtered lateral acceleration data and discounted additional test runs by the authors and NHTSA that did not support the supposed conclusions. This paper will discuss the effect of rim gouging using accepted scientific methods, including full vehicle testing where vehicle accelerations were measured during actual rim gouging events and static testing of side forces exerted by wheels mounted on a moving test fixture. The data analyzed in this paper clearly shows that forces created by rim gouges on pavement can be thousands of Newtons and can contribute to vehicle rollover.

Hybrid Electric Vehicles (HEV) utilize a High Voltage (HV) battery pack to improve fuel economy by maximizing the capture of vehicle kinetic energy for reuse. Consequently, these HV battery packs experience frequent and rapid charge-discharge cycles. The heat generated during these cycles must be managed effectively to maintain battery cell performance and cell life. The HV battery pack cooling system must keep the HV battery pack temperature below a design target value and maintain a uniform temperature across all of the cells in the HV battery pack. Herein, the authors discuss some of the design points of the air cooled HV battery packs in Ford Motor Company’s current model C-Max and Fusion HEVs. In these vehicles, the flow of battery cooling air was required to not only provide effective cooling of the battery cells, but to simultaneously cool a direct current high voltage to low voltage (DC-DC) converter module.

Fuel cell vehicles are entering the automotive market with significant potential benefits to reduce harmful greenhouse emissions, facilitate energy security, and increase vehicle efficiency while providing customer expected driving range and fill times when compared to conventional vehicles. One of the challenges for successful commercialization of fuel cell vehicles is transitioning the on-board fuel system from liquid gasoline to compressed hydrogen gas. Storing high pressurized hydrogen requires a specialized structural pressure vessel, significantly different in function, size, and construction from a gasoline container. In comparison to a gasoline tank at near ambient pressures, OEMs have aligned to a nominal working pressure of 700 bar for hydrogen tanks in order to achieve the customer expected driving range of 300 miles.