Search Results

Tire forces and moments play an important role in vehicle dynamics and safety. X-by-wire chassis components including active suspension, electronic powered steering, by-wire braking, etc can take the tire forces as inputs to improve vehicle’s dynamic performance. In order to measure the accurate dynamic wheel load, most of the researches focused on the kinematic parameters such as body longitudinal and lateral acceleration, load transfer and etc. In this paper, the authors focus on the suspension system, avoiding the dependence on accurate mass and aerodynamics model of the whole vehicle. The geometry of the suspension is equated by the spatial parallel mechanism model (RSSR model), which improves the calculation speed while ensuring the accuracy. A suspension force observer is created, which contains parameters including spring damper compression length, push rod force, knuckle accelerations, etc., combing the kinematic and dynamic characteristic of the vehicle.

Positioning system is a key module of autonomous driving. As for LiDAR SLAM system, it faces great challenges in scenarios where there are repetitive and sparse features. Without loop closure or measurements from other sensors, odometry match errors or accumulated errors cannot be corrected. This paper proposes a construction method of LiDAR anchor constraints to improve the robustness of the SLAM system in the above challenging environment. We propose a robust anchor extraction method that adaptively extracts suitable cylindrical anchors in the environment, such as tree trunks, light poles, etc. Skewed tree trunks are detected by feature differences between laser lines. Boundary points on cylinders are removed to avoid misleading. After the appropriate anchors are detected, a factor graph-based anchor constraint construction method is designed. Where direct scans are made to anchor, direct constraints are constructed.

With the development of brake-by-wire technology, electro-hydraulic composite braking technology came into being. This technology distributes the total braking force demand into motor regenerative braking force and hydraulic braking force, and can achieve a high energy recovery rate. The existing composite braking control belongs to single-channel control, i.e., the four wheel braking pressures are always the same, so the hydraulic braking force distribution relationship of the front and rear wheels does not change. For single-axle-driven electric vehicles, the additional regenerative braking force on the driven wheels will destroy the original braking force distribution relationship, resulting in reduced braking efficiency of the driven wheels, which are much easier to lock under poor road adhesion conditions.

The Chinese government and industries have proposed strategic plans and policies for automotive renewable-energy transformation in response to China’s commitments to peak the national carbon emissions before 2030 and to achieve carbon neutrality by 2060. We thus analyze the evolution of carbon emissions from the vehicle fleet in China with our data-driven models based on these plans. Our results indicate that the vehicle life-cycle carbon emissions are appreciable, accounting for 8.9% of the national total and 11.3% of energy combustion in 2020. Commercial vehicles are the primary source of automotive carbon emissions, accounting for about 60% of the vehicle energy cycle. Among these, heavy-duty trucks are the most important, producing 38.99% of the total carbon emissions in the vehicle operation stage in 2020 and 52.18% in 2035.

To overcome the shortcoming that vehicles with multiple steering modes need to switch steering modes at parking or very low speeds, a dynamic switch method of steering modes based on MOEA/D (Multi-objective Evolutionary Algorithm Based on Decomposition) was proposed for 4WID-4WIS (Four Wheel Independent Drive-Four Wheel Independent Steering) electric vehicle, considering the smoothness of dynamic switch, the lateral stability of the vehicle and the energy economy of tires. First of all, the vehicle model of 4WID-4WIS was established, and steering modes were introduced and analyzed. Secondly, the conditions for the dynamic switch of steering modes were designed with the goal of stability and safety. According to different constraints, the control strategy was formulated to obtain the target angle of the active wheels. Then aiming at the smoothness of the dynamic switch, the active wheel angle trajectory was constructed based on the B-spline theory.

This study investigated the plastic deformation behavior of 304 stainless steel thin-walled tubes under axial compression by means of numerical calculation and theoretical analysis. It was found that the plastic deformation length of thin-walled tube determined the formability of folds and the work done in the whole axial compression process. To reveal the relation between the range of plastic deformation length and tube geometry parameters, regression equations were established using the quadratic regression orthogonal design method. Experiments were conducted to validate the equations. The process windows for forming a single fold and tube joining at ends had been printed ultimately. The results showed that the regression equations can accurately predict the range of plastic deformation length for forming a single fold.

Proton Exchange Membrane Fuel Cell (PEMFC) uses hydrogen and oxygen for fuel, the whole energy conversion process almost has no negative impact on the environment. The PEM fuel cell stack with the advantages of low-operating temperature, high current density and fast start-up ability is considered to be the next generation of new electric vehicle power. However, due to the limited current output, it is difficult for a single cell to meet the practical application requirements. The actual fuel cell stack is formed by many single cells assembled together. The assembly process is often related to load transfer, material transfer, energy exchange, multi-phase flow, electrochemical reaction and other factors. The performance of MEA (Membrane Electrode Assembly), sealing gaskets and other components will change during the assembly process, which makes the fuel cell stack assembly process more complex.

Environmental perception is a crucial subsystem in autonomous vehicles. In order to build safe and efficient traffic transportation, several researches have been proposed to build accurate, robust and real-time perception systems. Camera and LiDAR are widely equipped on autonomous self-driving cars and developed with many algorithms in recent years. The fusion system of camera and LiDAR provides state-of the-art methods for environmental perception due to the defects of single vehicular sensor. Extrinsic parameter calibration is able to align the coordinate systems of sensors and has been drawing enormous attention. However, differ from spatial alignment of two sensors’ data, joint calibration of multi-sensors (more than two sensors) should balance the degree of alignment between each two sensors.

Millions of configurations of power-split hybrid powertrain can be generated due to variation in number of planetary-gear sets (PG), difference in number, type and installation location of shift actuators (clutches or brakes), and difference in connection positions of power components. Considering the large number of configurations, complex structures and control modes, it is vital to construct an appropriate multi-index system evaluation method, which directly affects the requirement fulfillment, the time and cost of 2-PG system configuration design. Considering one-sidedness (dynamics and economic performance), simplicity (linear combination of indicators) and subjectivity (relying on expert experience) of previous system evaluation method of 2-PG system design, a more systematic evaluation method is proposed in this paper. The proposed evaluation system consists of five aspects, involving dynamic, economy, comfort, reliability and cost, and more than 20 indexes.

This paper presents a theoretical study of a finite hybrid piezoelectric phononic crystal (PC) beam with shunting circuits. The vibration transmissibility method (TM) is developed for the finite system. The uniform and non-uniform configurations of the resonators, piezoelectric patches and shunting circuits are respectively considered. The properties of the vibration attenuation of the hybrid PC beam undergoing bending vibration are investigated and quantified. It is shown that the proper relaxation of the periodicity of the PC is conducive to forming a broad vibration attenuation region. The hybrid piezoelectric PC combines the purely mechanical PC with the piezoelectric PC and provides more tunable mechanisms for the target band-gap. Taking the structural and circuit parameters into account, the design of experiments (DOE) method and the multi-objective genetic optimization method are employed to improve the vibration attenuation and meet the lightweight demand of the attachments.

Tire cavity noise of pure electric vehicles is particularly prominent due to the absence of engine noise, which are usually eliminated by adding Helmholtz resonators with arbitrary transversal section to the wheel rims. This paper provides theoretical basis for accurately predicting and effectively improving acoustic performance of wheel resonators. A hybrid finite element method is developed to extract the transversal wavenumbers and eigenvectors, and the mode-matching scheme is employed to determine the transmission loss of the Helmholtz resonator. Based on the accuracy validation of this method, the matching design of the wheel resonators and the optimization method of tire cavity noise are studied. The identification method of the tire cavity resonance frequency is developed through the acoustic modal test. A scientific transmission loss target curve and fitness function are defined according to the noise characteristics.

A composite steering control strategy, which combines four-wheel steering (4WS) and differential steering, is proposed in this paper, to optimize steering maneuverability in the conditions where the vehicle speed is below 15 Km/h, mainly for U-turning and parking conditions. A dynamic model is developed for the steering system and the tire system. Taking different steering wheel inputs into consideration, a 4WS control strategy proportional to the front wheel steering angle is quoted to improve the steering maneuverability in the low speed conditions and guarantee the manipulability by controlling the side slip of the vehicle. Based on the 4WS system, this paper explores the possibility of further improving the low-speed maneuverability of the vehicle through differential steering. And the differential steering control strategy is developed, including four hub-motor output modes. A composite steering controller is designed based on the 4WS-4WD electric vehicle platform.

Velocity is one of the most important inputs of active safety systems such as ABS, TCS, ESC, ACC, AEB et al. In a distributed drive electric vehicle equipped with four in-wheel motors, velocity is hard to obtain due to all-wheel drive, especially in wheel slipping conditions. This paper focus on longitudinal velocity estimation of the distributed drive electric vehicle. Firstly, a basic longitudinal velocity estimation method is built based on a typical Kalman filter, where four wheel speeds obtained by wheel speed sensors constitute an observation variable and the longitudinal acceleration measured by an inertia moment unit is chosen as input variable. In simulations, the typical Kalman filter show good results when no wheel slips; when one or more wheels slip, the typical Kalman filter with constant covariance matrices does not work well. Therefore, a gain matrix adjusting Kalman filter which can detect the wheel slip and cope with that is proposed.

Electric wheel systems of in-wheel motor driven vehicles consist of the motor controller, in-wheel motor and tire-suspension assembly. The coupling between the electromagnetic excitation and elastic structure gives rise to electromechanical dynamic issues. As for the structural layout of the electric wheel system, the driving motor is directly connected to the wheel without torsion dampers or transmission in the driveline, thus making the electric wheel structure a weak damping system. Moreover, the driving torque of electric wheel can change rapidly in various conditions of vehicle. As a result, the transient vibration problem becomes one of the key electromechanical dynamic issues in the electric wheel system. To investigate this problem, the electromechanical coupling model of the electric wheel system is established first. Then the transient responses of the electric wheel under abrupt changes of the driving torque are simulated.

In China Cut-in scenarios are quite common on both highway and urban road with heavy traffic. They have a potential risk of rear-end collision. When facing a cutting in vehicle, driver tends to brake in most case to reduce collision risk. The timing and dynamic characteristics of brake maneuver are indicators of driver subjective risk perception. Time to collision (TTC) and Time Headway (THW) demonstrate objective risk. This paper aims at building a model quantitatively revealing the relationship between drivers’ subjective risk perception and objective risk. A total of 66 valid critical Cut-in cases was extracted from China-FOT, which has a travel distance of about 130 thousand miles. It is found that under Cut-in scenarios, driver tended to brake when the cutting in vehicle right crossing line. This time point was defined as initial brake time. Brake strength and brake speed were taken to describe brake maneuver.

Wheel Aerodynamics is an important part of vehicle aerodynamics. The wheels can notably influence the total aerodynamic drag, lift and ventilation drag of vehicles. In order to simulate the real on-road condition of driving cars, the moving ground and wheel rotation is of major importance in CFD. However, the wheel rotation condition is difficult to be represented exactly, so this is still a critical topic which needs to be worked on. In this paper, a study, which focuses on two types of cars: a fastback sedan and a notchback DrivAer, is conducted. Comparing three different wheel rotating simulation methods: steady Moving wall, MRF and unsteady Sliding Mesh, the effects of different methods for the numerical simulation of vehicle aerodynamics are revealed. Discrepancies of aerodynamic forces between the methods are discussed as well as the flow field, and the simulation results are also compared with published experimental data for validation.

Steering of skid-steered vehicles without steering mechanism is realized by differential drive/brake torque generated from in-wheel motors at left and right sides. Compared to traditional Ackerman-steered vehicles, skid-steered vehicles consume much more energy while steering due to greater steering resistance. Torque allocation is critical to the distributed drive skid-steered vehicles, since it influences not only steering performance, but also energy efficiency. In this paper, the dynamic characteristics of six-wheeled skid-steered vehicles were analyzed, and a 2-DOF vehicle model was established, which is important for both motion tracking control and torque allocation. Furthermore, a hierarchical controller was proposed. Considering tire force characteristics and tire slip, the upper layer calculates the generalized force and desired yaw moment based on anti-windup PI (proportion-integral) control method.

Carbon fiber reinforced plastic (CFRP) composites have gained particular interests due to their high specific modulus, high strength, lightweight and resistance to environment. In the automotive industry, numerous studies have been ongoing to replace the metal components with CFRP for the purpose of weight saving. One of the significant benefits of CFRP laminates is the ability of tailoring fiber orientation and ply thickness to meet the acceptable level of structural performance with little waste of material capability. This study focused on the concurrent optimization of ply orientation and thickness for CFRP laminated engine hood, which was based on the gradient-based discrete material and thickness optimization (DMTO) method. Two manufactural constraints, namely contiguity and intermediate void constraints, were taken into account in the optimization problem to reduce the potential risk of cracking matrix of CFRP.

In the assembling process of proton exchange membrane fuel cell (PEMFC) stack, the clamping load is known to have direct effect on the contact pressure of interfaces. Compression on the membrane electrode assembly (MEA) results in change in gas diffusion layer (GDL), porosity and electrical resistance, thus affecting the performance, durability and reliability of the PEMFC stack. In this paper, the relation between clamping load and performance of PEMFC stack was obtained by experimental study, and the influence of clamping load on the contact pressure of MEAs was analyzed by finite element analysis. The performance test rig was established and the approach of polarization curve testing was introduced. Both the effect of magnitude and distribution of the bolt torques on the performance were taken into account. The finite element model was adopted to figure out the magnitude and uniformity of contact pressure of MEAs, which provides a new angle to understand the experimental results.

In order to research the effect of process parameters (laser power, welding speed, wire-feed speed, spot diameter) on mechanical properties of Zn-coated Steel Laser Brazing Lap Joint for vehicle, the influence of welding parameters on energy input of brazing seam cross section was theoretically analyzed, and then a great number of laser brazing experiments of 0.7mm galvanized steel was carried out. After that, the tensile strength and micro-hardness tests were also done for well-formed joints of galvanized steel formed in the laser brazing. The results show that joints with good mechanical properties and surface morphology can be formed when laser power is in the range of 2500-3200W and the other parameters keep in a specified range. Joint performance significantly reduces when the value of wire-feed speed exceeds 3.0m/min for that a wider brazing seam cross section can’t be formed.