Search Results

This paper presents the test track scenario design and analysis used to estimate the performances of heavy vehicles equipped with forward collision warning and automatic emergency braking systems in rear-end crash scenarios. The first part of this design and analysis study was to develop parameters for brake inputs in test track scenarios simulating a driver that has insufficiently applied the brakes to avoid a rear-end collision. In the second part of this study, the deceleration limits imposed by heavy vehicles mechanics and brake systems are used to estimate automatic emergency braking performance benefits with respect to minimum stopping distance requirements set by Federal Motor Vehicle Safety Standards. The results of this study were used to complete the test track procedures and show that all heavy vehicles meeting regulatory stopping distance requirements have the braking capacity to demonstrate rear-end crash avoidance improvements in the developed tests.

This paper presents National Highway Traffic Safety Administration’s 2017 and 2018 test track research results with heavy vehicles equipped with forward collision warning and automatic emergency braking systems. Newly developed objective test procedures were used to perform and collect performance data with three single-unit trucks equipped with the crash avoidance systems. The results of this research show that the test procedures are applicable to many heavy vehicles and indicate that performance improvements in heavy vehicles equipped with these safety systems can be objectively measured.

Dynamic Brake Support (DBS) is a safety system that has been applied to various passenger cars and has been shown to be effective at assisting drivers in avoiding or mitigating rear-end collisions. The objective of a DBS system is to ensure that the brake system is applied quickly and at sufficient pressure when a driver responds to a collision imminent situation. DBS is capable of improving braking response due to a passenger car driver's tendency to utilize multi-stage braking. Interest is developing in using DBS on commercial vehicles. In order to evaluate the possible improvement in safety that could be realized through the use of DBS, driver braking behavior must first be analyzed to confirm that improvement is possible and necessary. To determine if this is the case, a study of the response of truck drivers' braking behavior in collision imminent situations is conducted. This paper presents the method of evaluation and results.

Torsional stiffness properties were developed for both a 53-foot box trailer and a 28-foot flatbed control trailer based on experimental measurements. In order to study the effect of torsional stiffness on the dynamics of a heavy truck vehicle dynamics computer model, static maneuvers were conducted comparing different torsional stiffness values to the original rigid vehicle model. Stiffness properties were first developed for a truck tractor model. It was found that the incorporation of a torsional stiffness model had only a minor effect on the overall tractor response for steady-state maneuvers up to 0.4 g lateral acceleration. The effect of torsional stiffness was also studied for the trailer portion of the existing model.

Direct vehicle performance comparisons were made between a full 6s/6m and a simpler 4s/4m system, as applied to a 6x4 Class 8 straight truck having a walking-beam rear suspension design. The 4s/4m system was run in both intermediate-axle control and trailing axle-control configurations. The systems were compared with modern air-disc brakes on the vehicle The systems were compared at LLVW (unladen) and GVWR (fully loaded) for high speed stopping performance and stability on a high-μ surface and a wetted split-μ surface, as well as Brake-in-Curve stability on a wetted low-μ 500-ft radius turn. In this paper, stopping distances are statistically compared to quantify effects of the various ABS control strategies on dry and wet stopping efficiency. In addition, newer techniques of using wheel-slip histograms generated from in-stop data are used to compare more detailed system behavior and predict their effects on vehicle stability under braking.

Due to increased speed limits at the state level, NHTSA has pursued additional testing of heavy trucks at higher test maneuver entry speeds. Test results from three vehicles, a Class 7 school bus, a Class 8 truck tractor and a Class 8 straight-truck are presented here. Results are discussed for full treadle straight-ahead stops from 60, 70 and 75 mph. Each vehicle was tested with two different brake configurations. As expected, higher entry speeds resulted in increased stopping distances. Causes for increased stopping distances are briefly discussed. Comparisons show that vehicles in the hybrid configuration (air-disc brakes on steer axle and S-cam brakes on drive axle(s)) had superior stopping performance to the vehicles equipped with traditional S-cam brakes. The vehicles in the hybrid configuration were less susceptible to increased stopping distances from higher entry speeds.

A test procedure that rates brake performance must control variability so that measured differences between vehicles are real. Tests were conducted using standard brake test procedures with three drivers in three cars on wet and dry asphalt with the ABS working and disabled. The differences between vehicles were greater than differences due to ABS condition, surface condition, and drivers. The procedure measured differences between all the vehicles with statistical certainty but used many replications and drivers. If only large differences in performance need to be distinguished, fewer replications and drivers will be needed.

Most fatalities due to school bus accidents involve pedestrians being struck by the bus. All too frequently the school bus strikes a disembarking passenger because the driver was unaware of their presence near the bus. To try to prevent this type of accident, two Doppler microwave radar-based pedestrian detection systems have been developed and are commercially available. These systems supplement regular school bus mirrors. They operate only while the bus is stationary. Both systems detect moving pedestrians either directly in front of or to the right of the bus. The National Highway Traffic Safety Administration has performed a three-part evaluation of these pedestrian detection systems. The first part measured the field of view of each system's sensors. The second part evaluated the effectiveness and appropriateness of each system's driver interface. The third part was a small-scale operational evaluation.