Search Results

Ammonia shows promise as an alternative fuel for internal combustion engines (ICEs) in reducing CO2 emissions due to its carbon-free nature and well-established infrastructure. However, certain drawbacks, such as the high ignition energy, the narrow flammability range, and the extremely low laminar flame speed, limit its widespread application. The dual fuel (DF) mode is an appealing approach to enhance ammonia combustion. The combustion characteristics of ammonia-diesel dual fuel mode and ammonia-PODE3 dual fuel mode were experimentally studied using a full-view optical engine and the high-speed photography method. The ammonia energy ratio (ERa) was varied from 40% to 60%, and the main injection energy ratio (ERInj1) and the main injection time (SOI1) were also varied in ammonia-PODE3 mode.

This paper analyzes the current control, mode control and boost strategy of permanent magnet synchronous motor in dual hybrid system, which has good stability and robustness. Current control includes current vector control, MTPA control, flux weakening control, PI current control and SVPWM control. Motor mode includes initialization mode, normal mode, fault mode, active discharge mode, power off mode, battery heating mode and boost mode. The boost strategy of the hybrid system is based on boost mode management, boost target voltage determination and boost PI control. The specific content is as follows: Boost mode control. Boost mode includes initial mode, normal mode, off mode and fault mode. Boost target voltage is determined. Boost converter is controlled by variable voltage, which depends on the operation status of the motor and generator..

With the capability of avoiding failure in advance, failure prediction model is important not only to end users, but also to the service engineers in vehicle industry. This paper proposes an approach based on anomaly detection algorithms and telematic data to predict the failure of the engine air system with Turbo charger. Firstly, the relationship between air system and all obtained features are analyzed by both physical mechanism and data-wise. Then, the features including altitude, air temperature, engine output power, and charger pressure are selected as the input of the model, with the sampling interval of 1 minute. Based on the selected features, the healthy state for each vehicle is defined by the model as benchmark. Finally, the ‘Medium surface’ is determined for specific vehicle, which is a hyperplane with the medium points of the healthy state located at, to detect the minor weakness symptom (sub-health state).

The collision accidents of electric vehicles are gradually increasing, and the response of battery cell under mechanical abuse conditions has attracted more and more attention. In the real collision, the mechanical load on battery generally has the following characteristics, including multiple loading directions, dynamic impact and blunt intrusion. Therefore, it is necessary to study the mechanical response and deformation of battery under complex loading, especially in-plane dynamic loading condition. According to the actual accident, we designed the constrained blunt compression test of the battery in different speeds and directions. For out-of-plane loading, the structural stiffness of battery increases obviously and the fracture is advanced compared with the corresponding quasi-static tests. For in-plane constrained loading, the force response can be approximately divided into two linear segments, in which the structural stiffness increases abruptly after the inflection point.

With the rapid advancement in intelligent vehicle technologies, comprehensive environmental perception has become crucial for achieving higher levels of autonomous driving. Among various perception tasks, monitoring road types and evenness is particularly significant. Different road categories imply varied surface adhesion coefficients, and the evenness of the road reflects distinct physical properties of the road surface. This paper introduces a two-stage road perception framework. Initially, the framework undergoes pre-training on a large annotated drivable area dataset, acquiring a set of pre-trained parameters with robust generalization capabilities, thereby endowing the model with the ability to locate road areas in complex regions.

In order to realize the series-parallel switching control of hybrid electric vehicle (HEV) with dual-motor hybrid configuration, a method of unpowered interrupt switching based on the coordinated control of three power sources was proposed by analyzing the series-parallel driving mode of the dual-motor hybrid configuration. The series to parallel switching process is divided into three stages: speed regulation stage, clutch combination and power source switching. The distribution control of speed regulating torque is carried out in the speed regulating stage. The speed adjustment torque is preferentially allocated to the power source of the input shaft (engine and P1) to carry out the lifting torque. Due to the high speed adjustment accuracy and fast response of the P1 motor, the input shaft is preferentially allocated to P1 for speed adjustment, that is, the torque intervention of P1.

In order to realize the shift control of dual-motor hybrid electric vehicle (HEV), a non-power interruption shift control method based on three-power source coordination control was proposed by analyzing the shift process of dual-motor hybrid configuration. The shift control process was divided into three stages: oil-filling self-learning stage, torque exchange stage and inertia control stage. In the torque exchange stage, the characteristics of the speed stage and torque stage were analyzed, which was different from the traditional method's dependence on pressure sensor, longitudinal acceleration sensor and engine torque accuracy. A shift clutch gain self-learning strategy based on shift time and input shaft speed soaring problem was proposed.

In order to achieve seamless mode switching control for hybrid electric vehicles (HEVs) in the event of battery failure, we propose a motor voltage-controlled mode switching method that eliminates power interruptions. This approach is based on an analysis of the dual-motor hybrid configuration's mode switching. We analyze the overall vehicle operation when the high-voltage battery occurs in different hybrid modes. To ensure that the vehicle can still function like a conventional car under such circumstances, we introduce a novel "voltage control" mode. In this mode, instead of operating in its traditional torque control manner, the P1 motor adopts a voltage control strategy. The P1 controller's variable becomes "voltage," and VCU sends the motor's working mode switching request and PCM finishes the mode transition. During system operation, the P1 motor promptly responds to these target voltages to maintain bus voltage within a normal range.

In order to solve the problems of the shuffle caused by internal and external excitation and the difficulty in obtaining the real-time accurate engine torque during the parallel mode operation of hybrid electric vehicles, a dynamic coordination control strategy for suppressing the jitter of hybrid electric vehicles based on the closed-loop control of engine speed was proposed. The engine torque filtering control method based on the slope limit was adopted to limit the rate of change of the engine torque and reduce the impact caused by the sudden change of the engine torque; the engine speed closed-loop control method was used to take the motor speed which is easy to be measured accurately in real time as the feedback control variable, which solved the problem of the real-time accurate estimation of the engine torque online. In parallel mode, the motor torque accounts for a small proportion because the torque distribution method gives priority to the engine.

In hybrid vehicles, the drive motor is directly connected to the drive train and the inherent drive train damping is low. When subjected to external disturbance, the low damping characteristics of the transmission system may cause torsional vibration, which will continue to oscillate the transmission system and affect the driving performance of the vehicle. In this paper, we propose a harmonic injection wheel control method based on motor speed to suppress oscillations and improve the driving performance of hybrid electric vehicles. The harmonic injection control method based on motor speed is based on Fourier transform to decompose sinusoidal harmonics based on specific order of motor speed. RLS algorithm is used to estimate the amplitude and phase, and PI control is used to calculate the compensation torque for the actual amplitude and target amplitude. Simulation and test results show that the proposed control strategy is effective in suppressing oscillations.

Due to the objectives of achieving high fuel efficiency and drivability performance, a dual-drive hybrid system with two motors has been developed. Various drive modes are presented based on engine status, requested driver torque and power, as well as C0 status in different working conditions. The transition control of drive mode change poses a unique challenge for the dual-drive hybrid system. This study discusses the control strategies for transitioning between drive modes. The first type of transition mode is divided into four distinct phases. In the second mode transition, there are three phases: the synchronization phase involving P1 torque intervention, the C0 lock-up phase involving frozen P1 torque control and adjustment of C0 clutch torque and pressure correlation, and finally, the torque exchange phase. The third type of transition includes a dedicated torque transition phase followed by a C0 disengaged phase and concluding with a speed synchronization phase.

The driving risk field model offers a feasible approach for assessing driving risks and planning safe trajectory in complex traffic scenarios. However, the conventional risk field fails to account for the vehicle size and acceleration, results in the same trajectories are generated when facing different vehicle types and unable to make safe decisions in emergency situations. Therefore, this paper firstly introduces the acceleration and vehicle size of surrounding vehicles for improving the driving risk model. Then, an integrated decision-making and planning model is proposed based on the combination of the novelty risk field and model predictive control (MPC), in which driving risk and vehicle dynamics constraints are taken into consideration. Finally, the multiple driving scenarios are designed and analyzed for validate the proposed model.

To characterize emission performance and engine operating conditions during high-power cold starts (HPCS), a blended plug-in hybrid electric vehicle was tested over worldwide harmonized light-duty vehicle test cycle (WLTC), and a new cycle was developed to characterize HPCS. The results showed that the engine speed and load increased dramatically to high level during HPCS under the low temperature of coolant and catalysts. The higher concentration of particle number (PN) and NOx at higher speed and load, accounted for the higher emissions during HPCS. Besides, the cumulative PN emissions increased first and then decreased with the increasing coolant temperature.

Accurate identification of driver’s braking intention is essential in advanced driver assistance system and can make the driving process more comfortable and trustworthy. In this paper, a novel method for driver braking intention identification in cut-in scenarios was proposed by using driver’s gaze information and motion information of cut-in vehicles. Firstly, a "looking in and looking out" experimental platform including three eye-tracking cameras and one front-view camera was built to collect driver's gaze information and the vehicle motion information. Secondly, driver’s gaze features and motion features of cut-in vehicles were selected and the braking intention identification performance of several decision tree-based ensemble learning algorithms was compared. Thirdly, the feature importance was analyzed by using SHAP (SHapley Additive exPlanations) values. This novel method of braking intention identification makes full use of in-vehicle camera sensors.

The desired yaw rate is a vital target parameter for vehicle stability control, which is currently determined as a steady-state yaw rate by the linear single-track vehicle model. Tire nonlinearity deteriorates the effect of vehicle stability control at larger lateral acceleration. This paper proposes a new calculation method of the steady-state yaw rate considering the tire nonlinearity based on the brush tire model. To validate and verify the proposed method, step steering tests of the target vehicle under different lateral accelerations are carried out on a real proving ground. The results show that when the lateral acceleration is relatively small, the difference between the calculation results of the proposed method and the traditional one is not apparent, and both methods can provide a good estimation for the steady-state yaw rate; however, when the lateral acceleration is relatively large, the difference becomes apparent.

China's plug-in electric vehicle (PEV) market with stocks at 7.8 million is the world's largest in 2021, and it accounts for half of the global PEV growth in 2021. The PEV market in China has dramatically evolved since the pandemic in 2020: over 20% of all new PEV sales are from China by mid-2022. Recent features of PEV market dynamics, consumer acceptance, policies, and infrastructure have important implications for both the global energy market and manufacturing stakeholders. From the perspective of demand pull-supply push, this study analyzes China's PEV industry with a market dynamics framework by reviewing sales, product and brand, infrastructure, and government policies from the last few years and outlooking the development of the new government’s 14th Five-Year Plan (2021-2025).

The recent proliferation of perception sensing and computing technologies has promoted the rapid development of automated driving. The design of the perception sensing system has nonnegligible influences both on the performances of various automated driving features and on the system costs. This paper proposes an automated driving feature oriented framework for automatic selection and arrangement of the sensors in the perception sensing system. An automated driving feature oriented optimization model is built considering the characteristics and requirements of the specific feature and a genetic algorithm based design method is provided to solve this optimization model. Furthermore, the Adaptive Cruise Control feature and the Automated Parking Assistance feature are selected as the simulation cases to verify the effectiveness of the proposed method.

An intelligent connected vehicle (ICV) swarm system that includes N vehicles is considered. Based on the special properties of potential functions, a kinematic model describing the swarm performances is proposed, which allows all vehicles to enclose the tracking target and show both tracking and formation characteristics. Treating the performances as the desired constraints, the analytical form of constraint forces can be obtained inspired by the Udwadia-Kalaba approaches. A special approach of uncertainty decomposition to deal with uncertain interferences is proposed, and a switching-type robust control method is addressed for each vehicle agent in the swarm system. The features and validity of the addressed control are demonstrated in the numerical simulations.

The intelligent unmanned ground vehicle (UGV) motorcade system consisting of one leader and n − 1 followers is considered. The safety distance between the front and rear UGVs is treated as the control target. Since the safety distance constraint is a unilateral constraint, the state transformation is needed. Hence, a piecewise type conversion function is formulated to serve for the transformation of the original inequality constraint. The system equation is further expressed by the new state. We assume that the input of the leading UGV is known. Combined with the uncertainty evaluation, a class of collaborative controls for the following UGVs is proposed to deal with the uncertainty with unknown bound. The effectiveness of the designed control is verified by both Lyapunov stability theory and simulations. Both theoretical and simulation results illustrate that the longitudinal safety, stability and global behavior of the intelligent motorcade system are guaranteed.

In order to obtain a good understanding of mechanical behaviors of lithium-ion battery modules in electric vehicles, comprehensive experimental and numerical investigations were performed in the study. Mechanical indentation tests with different indentation heads, different loading directions and different impact speeds were performed on battery modules with prismatic cells. To mitigate thermal runaway, only fully discharged battery modules were used. The force-displacement responses and open circuit voltage were recorded and compared. It was found that the battery modules experienced different failure modes when subjected to mechanical abuse. Besides internal short circuit of cells, external short circuit from bus bar and vapor leakage of electrolyte were also found to deteriorate the mechanical and electrical integrity of the tested modules. Mechanical anisotropy and dynamic effect were found on the battery module.