Search Results

In this research helical Carbon Nanotubes (CNTs) with various weight percentages as an additional reinforcement were used. The objective was to investigate the effectiveness of helical geometries of the CNTs to form interlocking mechanisms with the resin and the traditional microfiber reinforcements to improve the overall performance of the composite structures and assemblies. In this study, ASTM D2344/2344M-16 is used to study the short beam strength of the laminated nanocomposites and evaluate the benefit of the mechanically interlocked helical CNTs reinforcement. Overall, three sets of composite laminates (i.e., with neat epoxy, and with two different wt% of Helical CNTs reinforced epoxy) were fabricated per ASTM standard D2344/2344M-16. Adequate test specimens were prepared and then they were tested per ASTM standard. The test results were analyzed and evaluated to determine the effects of helical CNTs on short beam strength of the laminated nanocomposites.

Most composite assemblies and structures generally fail due to weak interlaminar properties and poor performance of their bonded joints that are assembled together with an adhesive layer. Adhesive failure and cohesive failure are among the most commonly observed failure modes in composite bonded joint assemblies. These failure modes occur due to the lack of reinforcement within the adhesive layer in transverse direction. In addition, the laminated composites fail due to the same reason that is the lack of reinforcement through the thickness direction between the laminae. The overall performance of any composite structures and assemblies largely depends on the interlaminar properties and the performance of its bonded joints. Various techniques and processes were developed in recent years to improve mechanical performance of the composite structures and assemblies, one of which includes the use of nanoscale reinforcements in between the laminae and within the adhesive layer.

The Refill Friction Spot Joining (RFSJ) is an emerging solid-state spot welding technology that thermo-mechanically creates a molecular-level bond between the work-pieces. RFSJ does not consume any filler or foreign materials so that no additional weight is introduced to the assembly. As the solid-to-liquid phase transition is not involved in RFSJ in general, there is no lack of fusion or material deterioration caused by liquefaction and solidification. Unlike the conventional friction stir spot welding, RFSJ produces a spot joint with a perfectly flush surface finish without a key or exit hole. Currently, the aerospace industry employs solid rivets for fastening the primary structures as they meet the baseline requirements and have well-established standards and specifications.

The necessity of avoiding the destructive and non-repeatable FSST (Full Scale Sled Test) makes it desirable to devise a cheaper and more repeatable method which can supplant this test procedure. This need developed the HCTD (HIC Component Testing Device) which is capable of providing conservative HIC results with higher repeatability. The computational model of the HCTD is validated against one of the tests conducted at CAMI with polyethylene foam. This validated model is used to conduct a series of tests with input parameters similar to the sled test to develop the correlation between the sled test and HCTD. This study hence concludes that a validated computational model of HCTD can be successfully utilized to address the HIC compliance issues for a foam padded surface.

The fatigue behavior of Hilok fastener joints under constant amplitude loading has been investigated experimentally. The effects of load transfer in an unbalanced joint configuration was characterized in terms of a stress severity factor relative to the open-hole configuration. The experimental data indicates that the clamp-up forces dominate the performance of fastener joints with the open-hole fatigue life being the lower bound at the stress levels investigated. The failure modes were observed to transition from a net-section type failure across the minimum section to a fretting induced failure at some distance from the hole. The experimental data has been used to develop stress severity factors to be used as a measure of the fatigue quality of the fastener joints.

In the present work we studied the edge trimming process of CFRP with a diamond interlocking “burr” tool. Measurements of tool wear, surface roughness, spindle power and delamination depth were performed for different combinations of spindle speed and feed rate and were subsequently used to characterize machining quality. It was found that direct wear measurement for this type of cutting tool is not conclusive and thus not suitable for assessing tool life and machining quality. Instead, indirect indicators of tool wear were found more suitable for this purpose. Using these indirect methods an equation for tool life was defined and parameters for optimum machining quality were determined.

A series of carefully selected tests were used to isolate the coupled influence of various combinations of the number of facesheet plies, impact energies, and impactor diameters on the damage formation and residual strength degradation of sandwich composites due to normal impact. The diameter of the planar damage area associated with Through Transmission Ultrasonic C-scan and the compression after impact measurements were used to describe the extent of the internal damage and residual strength degradation of test panels, respectively. Standard analysis of variance techniques were used to assess the significance of the regression models, individual terms, and the model lack-of-fit. In addition, the inherent variability associated with given types of experimental measurements was evaluated.

The coupled influence of material configuration (number of facesheet plies, core density, core thickness) and impact parameters (impact velocity and energy, impactor diameter) on the impact damage resistance characteristics of sandwich composites comprised of carbon-epoxy woven fabric facesheets and Nomex honeycomb cores was investigated using empirically based quadratic response surfaces. The diameter of the planar damage area associated with TTU C-scan measurements and the peak residual facesheet indentation depth were used to describe the extent of internal and detectable surface damage, respectively. Estimates of the size of the planar damage region correlated reasonably well with experimentally determined values. For a fixed set of impact parameters, estimates of the planar damage size and residual facesheet indentation suggest that impact damage development is highly material and lay-up configuration dependent.

During this study, a number of 8.5-inch by 11.5-inch flat honeycomb sandwich panels were inflicted with low energy impact damage, inspected non-destructively, and tested for residual in-plane compressive strength. Each panel had either a 3/8-inch or 3/4-inch low density Nomex honeycomb core, and either 2-ply, 4-ply or 6-ply face sheets. The face sheets were either carbon or Eglass (prepreg) fabric. The panels were either clamped or simply supported in a test fixture during impact from a gravity assisted drop mechanism, and impacted with either a 1-inch or 3-inch diameter spherical indenter. After impact the damage to each panel was characterized by (1) ultrasonic through-transmission to obtain a c-scan representing planar damage area, (2) indentation volume and depth, and finally (3) visual inspection to rate the damage according to a predetermined rating scale. The panels were then tested for in-plane compressive strength.

An aging aircraft accumulates fatigue cracks commonly referred to as multiple site damage (MSD). A simplified engineering fracture mechanics model, generally referred to as the linkup model (or plastic zone touch model), has been used with some success to describe the MSD fracture phenomenon in 2024-T3 aluminum panels. A disadvantage of the linkup model is that it gives excessively inaccurate results for some configurations. A modified linkup model has been developed through empirical analysis of test data taken from unstiffened panels with MSD cracks at open holes. The modified linkup model was then validated with test data from stiffened panels including single-bay panels with the lead crack centered between stiffeners and two-bay panels with the lead crack centered beneath a severed stiffener. Further validation of the modified linkup model was done with test data from panels with bolted lap joints. Test results were obtained from 112 different panels.

This paper presents the experimental study of hole quality parameters in the drilling of titanium alloy (6Al-4V). Titanium alloy plates were drilled dry using three types of solid carbide drills i.e. 2-flute helical twist drill, straight flute and three-flute drill. The objective was to study the effects of process parameters like feed rate, speed and drill bit geometry on the hole quality features. Typical hole quality features in a drilling process are the hole quality measures such as surface roughness, hole diameter, hole roundness and burr height. The results indicate that proper selection of speed, feed rate, and drill geometry can optimize metal removal rate and hole quality.

The competitive market has forced the industry to develop methodologies to reduce lead-time of the products without sacrificing quality. One of the major metal removal operations in the aerospace industries is drilling. Over 100,000 holes are made for a small single engine aircraft. Naturally, demand for faster production rate results in the demand for high-speed drilling. But the cost of hole-making operations becomes a significant portion of the total manufacturing cost. This paper discusses the high speed drilling of Al-2024-T3 alloy, the effect of feed and speed on hole quality features like oversize, roundness error, burr height and surface roughness.

The work presented here illustrates the wear behavior of CVD diamond coated carbide tools during the machining of carbon fiber-reinforced composites. Cutting experiments were conducted on a CNC milling machine for edge trimming of a 9-mm thick multi-layered carbon fiber-reinforced epoxy laminate in a climb cutting configuration. The effects of feed speed and diamond film thickness on the wear behavior of the coated tools were determined. In addition, characteristics of the worn cutting edge were studied using optical and scanning electron microscopes. It was shown that diamond coated tools generally performed better than the uncoated tools under all conditions. Uniform wear by abrasion of the diamond film, without exposing the substrate, was obtained when cutting at low feed speeds with thicker coatings. At higher feed speeds the wear of the coated tools was characterized by abrasion through the diamond film and exposure and wear of the substrate.

Composites are finding more and more applications in the aircraft industry. Drilling good quality holes is a major challenge for the manufacturing industry. The major factors which have an effect on hole quality are cutting parameters like speed and feedrate, machine rigidity, tool material, workpiece material, and tool geometry. The hole quality was studied by measuring the hole diameter and visually observing other parameters like shape and fiber breakout. Force analysis indicates that thrust increases with an increase in feedrate. Speed does not seem to have a very significant effect on thrust. The tool geometry plays a very important role in fiber pullout.

The residual strength of an aluminum panel with a centric hole and one cracked ligament was investigated experimentally. Each of the 7075-T6 aluminum panels which were tested included a cracked ligament of varying length on one side of the centric hole and an uncracked ligament on the other side of the hole. The failure of such a panel subjected to uniform tensile loading normally occurs according to the lower of two modes: brittle fracture or a net section type of yielding. On the other hand, the question of whether one or both ligaments fail is not easily answered. Results show that one or two ligament failure depends upon test conditions such as crack length and loading method. For short crack lengths, the uncracked ligament will fail almost simultaneously with the failure of the cracked ligament.

Multiple site damage (MSD) on aging aircraft accumulates from fatigue loading over a period of time. For ductile materials such as 2024-T3 aluminum, MSD may lower the strength below that which is predicted by conventional fracture mechanics. An analytical model referred to as the linkup (or plastic zone touch) model has previously been used to describe this phenomenon. However, the linkup model has been shown to produce inaccurate results for many configurations. This paper describes several modifications of the linkup model developed from empirical analyses. These modified linkup models have been shown to produce accurate results over a wide range of configurations for both unstiffened and stiffened flat 2024-T3 panels with MSD at open holes. These modified models are easy to use and give quick and accurate results over a large range of parameters.

An experimental study was conducted to investigate ice-adhesion on clean and coated aluminum surfaces. A test apparatus using the parallel plate linear shear technique was designed along with a data acquisition system for conducting the tests and recording the experimental data. A low pulling rate was applied to specially prepared test specimens for measuring the strength of ice adhesion for a range of test conditions. The effects of surface roughness, surface contamination, and water impurity on ice adhesion were investigated. In addition, tests were conducted to evaluate the effectiveness of a low ice-adhesion coating applied to aluminum test specimens. The results obtained showed that the bond between ice and metal was considerably lower for tap water than for distilled water. For the clean and coated aluminum surfaces the strength of ice adhesion varied with specimen roughness. However, no clear trend was established between ice adhesion strength and surface roughness.

Drilling is one of the most widely applied manufacturing operations. Millions of holes are drilled today in manufacturing industries especially in aerospace industry where high quality holes are essential. Rejection and rework rate of the products because of the bad hole is quite high. In this research graphite/honeycomb composite material and aluminum sheet metal has been used. The results show that drill geometry, speed and feed rate have substantial effects on the hole quality and also there was gradual variation of the thrust and lateral forces with feed rates.

Flight test experiments were conducted to measure the extent and nature of natural laminar flow on a smoothed test region of a swept-wing business jet wing. Surface hot film aneraometry and sublimating chemicals were used for transition detection. Surface pressure distributions were measured using pressure belts. Engine noise was monitored by a microphone attached to the wing surface to study possible acoustic effects on stability of the laminar boundary layer, Side-slip conditions were flown to simulate changes in effective wing sweep. Flight instrumentation and ground data analysis techniques and a method for measuring intermittency of turbulence are described, Correlation was obtained between the hot film gage signals and chemicals for transition detection. Cross-flow vortices were observed for some flight conditions. Results of spectral and statistical analysis of the hot film signals for various flight test conditions are presented.

Laminated metal-metal composites can have attractive fracture toughness properties; they also offer potentially good fatigue performance. These attributes are reviewed and prospects for improvement discussed. Weak interlaminar bonds are seen to be important, while quite thin layers seem to be most promising for laminates of higher strength materials. The experimental program utilized 0.033 in (0.84 mm) thick laminae of 7075-T6 aluminum alloy, adhesively bonded. Eight-layer composites were compared with solid sheets of nearly the same total metal thickness. Both fracture toughness and fatigue properties were determined. Kc values of more than double the KIc for this alloy were observed in the laminates, while fatigue performance as indicated by comparative S-N curves was found to be slightly improved.