Search Results

On-board emissions measurement for heavy-duty vehicles has taken on greater significance because new standards now address in-use emissions levels in the USA. Emissions compliance must be shown in a “Not-to-exceed” (NTE) zone that excludes engine operation at low power. An over-the-road 1996 Peterbilt tractor was instrumented with the West Virginia University Mobile Emissions Measurement System (MEMS). The researchers determined how often the truck entered the NTE, and the emissions from the vehicle, as it was driven over different routes and at different test weights (20,740 lb, 34,640 lb, 61,520 lb, and 79,700 lb) The MEMS interfaced with the truck ECU, while also measuring exhaust flowrate, and concentrations of carbon dioxide (CO2) and oxides of nitrogen (NOx) in the exhaust. The four test routes that were employed included varying terrain types in order to simulate a wide range of on-road driving conditions. One route (called the Bruceton route) included a sustained hill climb.

The Tapered Element Oscillating Microbalance (TEOM) measures captured particle mass continuously on a small filter held on an oscillating element. In addition to traditional filter-based particulate matter (PM) measurement, a TEOM was used to characterize PM from the dilute exhaust of trucks examined in two phases (Phase 1.5 and Phase 2) of the Coordinating Research Council (CRC) Heavy-Duty Vehicle Emissions Inventory Project E-55/E-59. Test schedules employed were the Heavy Heavy-Duty Diesel Truck (HHDDT) test schedule that consists of four modes (Idle, Creep, Transient and Cruise), the HHDDT Short (HHDDT_S) which represents high-speed freeway operation, and the Heavy-Duty Urban Dynamometer Driving Schedule (UDDS). TEOM results were on average 6% lower than those from traditional particulate filter weighing. Data (in units of g/cycle) were examined by plotting cycle-averaged TEOM mass against filter mass. Regression (R2) values for these plots were from 0.88 to 0.99.

Significant numbers of transit buses now operate on natural gas. With support of the U.S. Department of Energy, the National Renewable Energy Laboratory has evaluated the cost, performance, and emissions of alternative fuel buses around the country. In this study, three natural gas and three closely matched diesel buses were compared. The buses, built by World Trans, were 26′5″long and used 1997 Cummins B-series engines. Particulate matter and oxides of nitrogen emissions from the natural gas buses were significantly lower than those from the diesel buses. However, the diesel buses had lower operating costs and higher fuel efficiency than the natural gas buses.

Synthetic diesel fuel can be made from a variety of feedstocks, including coal, natural gas and biomass. Synthetic diesel fuels can have very low sulfur and aromatic content, and excellent autoignition characteristics. Moreover, synthetic diesel fuels may also be economically competitive with California diesel fuel if produced in large volumes. Previous engine laboratory and field tests using a heavy-duty chassis dynamometer indicate that synthetic diesel fuel made using the Fischer-Tropsch (F-T) catalytic conversion process is a promising alternative fuel because it can be used in unmodified diesel engines, and can reduce exhaust emissions substantially. The objective of this study was a preliminary assessment of the emissions from older model transit operated on Mossgas synthetic diesel fuel. The study compared emissions from transit buses operating on Federal no. 2 Diesel fuel, Mossgas synthetic diesel (MGSD), and a 50/50 blend of the two fuels.

Emissions of six 32 passenger transit buses were characterized using one of the West Virginia University (WVU) Transportable Heavy Duty Emissions Testing Laboratories, and the fixed base chassis dynamometer at the Colorado Institute for Fuels and High Altitude Engine Research (CIFER). Three of the buses were powered with 1997 ISB 5.9 liter Cummins diesel engines, and three were powered with the 1997 5.9 liter Cummins natural gas (NG) counterpart. The NG engines were LEV certified. Objectives were to contrast the emissions performance of the diesel and NG units, and to compare results from the two laboratories. Both laboratories found that oxides of nitrogen and particulate matter (PM) emissions were substantially lower for the natural gas buses than for the diesel buses. It was observed that by varying the rapidity of pedal movement during accelerations in the Central Business District cycle (CBD), CO and PM emissions from the diesel buses could be varied by a factor of three or more.

Speed-time and video data were logged for tractor-trailers performing local deliveries in Akron, OH. and Richmond, VA. in order to develop an emissions test schedule that represented real truck use. The data bank developed using these logging techniques was used to create a Yard cycle, a Freeway cycle and a City-Suburban cycle by the concatenation of microtrips. The City-Suburban driving cycle was converted to a driving route, in which the truck under test would perform at maximum acceleration during certain portions of the test schedule. This new route was used to characterize the emissions of a 1982 Ford tractor with a Cummins 14 liter, 350 hp engine and a 1998 International tractor with a Cummins 14 liter, 435 hp engine. Emissions levels were found to be repeatable with one driver and the driver-to-driver variation of NOx was under 4%, although the driver-to-driver variations of CO and PM were higher.

Series hybrid electric vehicles (HEVs) require power-plants that can generate electrical energy without specifically requiring rotary input shaft motion. A small-bore working prototype of a two-stroke spark ignited linear engine-alternator combination has been designed, constructed and tested and has been found to produce as much as 316W of electrical energy. This engine consists of two opposed pistons (of 36 mm diameter) linked by a connecting rod with a permanent magnet alternator arranged on the reciprocating shaft. This paper presents the numerical modeling of the operation of the linear engine. The piston motion of the linear engine is not mechanically defined: it rather results from the balance of the in-cylinder pressures, inertia, friction, and the load applied to the shaft by the alternator, along with history effects from the previous cycle. The engine computational model combines dynamic and thermodynamic analyses.

When performing a transient test on a heavy-duty engine as outlined in the Code of Federal Regulations (CFR), defined regression values of engine speed, torque and power must meet specific tolerances for the test to be considered valid. Regression of actual engine feedback data against target points from a schedule defined from an engine map is performed using the method of least squares to determine the slope, intercept, coefficient of regression and standard error of the estimate. To minimize the biasing effects of time lag between actual and schedule data, shifting of the data in the time domain prior to analysis and certain point deletions are permitted. There are presently no regression criteria available for heavy duty chassis testing. This leaves facilities performing these chassis tests with no suitable guidelines to validate individual tests. This study applies the regression analysis used in engine testing to chassis testing and examines the difficulties encountered.

Both field research and certification data show that the lean burn natural gas powered spark ignition engines offer particulate matter (PM) reduction with respect to equivalent diesel power plants. Concerns over PM inventory make these engines attractive despite the loss of fuel economy associated with throttled operation. Early versions of the Cummins L-10 natural gas engines employed a mixer to establish air/fuel ratio. Emissions measurements by the West Virginia University Transportable Heavy Duty Emissions Testing Laboratories on Cummins L-10 powered transit buses revealed the potential to offer low emissions of PM and oxides of nitrogen, (NOx) but variations in the mixture could cause emissions of NOx, carbon monoxide and hydrocarbons to rise. This was readily corrected through mixer repair or readjustment. Newer versions of the L-10 engine employ a more sophisticated fueling scheme with feedback control from a wide range oxygen sensor.

The fuel cell bus program at Georgetown University (GU) has directed the operational development and testing of three hybrid fuel cell powered buses for transit operation. These are the world's first liquid-fueled, fuel cell powered road vehicles. This paper describes the emissions testing of one of these buses on a heavy duty chassis dynamometer at West Virginia University (WVU). The tested bus was driven by a 120 kW DC motor and utilized a 50 kW phosphoric acid fuel cell (PAFC) as an energy source with a 100 kW battery for supplemental power. A methanol/water fuel mixture was converted by a steam reformer to a hydrogen rich gas mixture for use in a fuel cell stack. Emissions from the reformer, fuel cell stack and startup burner were monitored for both transient and steady-state operation.

Growing concern over ground-level ozone and its role in smog formation has resulted in extensive investigation into identifying ozone sources. Motor vehicle exhaust, specifically oxides of nitrogen and hydrocarbons, have been identified as major ozone precursors in urban areas. Past research has concentrated on assessing the impact of emissions from gasoline fueled light duty vehicles. However, little work has been done on identifying ozone precursors from medium and heavy duty diesel fueled vehicles. This paper presents the results of testing performed on a Navistar T 444E 190 horsepower diesel engine which is certified as a light/heavy-duty emissions classification and is used in medium duty trucks up to 11,800 kg (26,000 lb) GVW. Regulated emissions and speciated hydrocarbon emissions were collected using a filter, bag and Tenax adsorption cartridges for both steady state and transient engine operation.

Concern over atmospheric pollution has led to the development of testing procedures to evaluate the hydrocarbon, carbon dioxide, carbon monoxide and oxides of nitrogen emissions from internal combustion engines. In order to perform emissions testing on vehicles, a chassis dynamometer capable of simulating expected driving conditions must be employed. West Virginia University has developed a Heavy Duty Transportable Emissions Testing Laboratory to perform chassis testing on trucks and buses. Emissions from the vehicle are monitored and recorded over the duration of a testing schedule. Usually the vehicle emissions from the whole test are reported as mass of emissions per unit distance driven. However, there is interest in relating the instantaneous emissions to the immediate conditions at specific points in the test, and in determining the emissions for discrete segments of the test (modal analysis).

Emissions from light duty vehicles have traditionally been measured using a chassis dynamometer, while heavy duty testing has been based on engine dynamometers. However, the need for in-use vehicle emissions data has led to the development of two transportable heavy duty chassis dynamometers capable of testing buses and heavy trucks. A test cycle has been developed for Class 8 trucks, which typically have unsyncronized transmissions. This test cycle has five peaks, each consisting of an acceleration, cruise period, and deceleration, with speeds and acceleration requirements that can be met by virtually all vehicles in common service. Termed the “WVU 5 peak truck test”, this 8 km (5 mile) cycle has been used to evaluate the emissions from diesel and ethanol powered over-the-road tractors and from diesel and ethanol powered snow plows, all with Detroit Diesel 6V92 engines.

In order to obtain meaningful analyses of exhaust gas emissions and fuel economy for a heavy duty vehicle from a chassis dynamometer, the accurate simulation of road load characteristics is crucial. The adjusted amount of power to be absorbed by the chassis dynamometer during road driving of the tested vehicle needs to be calculated. In this paper, the performance of the chassis dynamometer under transient load cycle operations is discussed and the transient response of the power absorption system is presented. In addition, the design criteria of the chassis dynamometer used to test heavy duty vehicles under steady and transient load is described.