Search Results

Distributed steering vehicle uses four steering motors to achieve four wheel independent steering. The steering angle of each wheel can be distributed respectively. The tire cornering characteristics are added to traditional steering model to study the angle allocation control algorithm. Using the constraint relation between tire slip angle, vehicle speed, yaw rate and front steering angle, and connecting with the ideal ackermann steering relationship, steering angle allocation of front wheel independent steering and four wheel independent steering is derived. Then simulated analysis is carried out to demonstrate the efficiency of the algorithm. Improvements in tire wear condition are determined by evaluating the optimization in tire lateral force, and the vehicle stability is determined by vehicle slip angle. The simulation results show that the angle allocation control algorithm has a good effect on improving tire wear condition and enhancing the stability of vehicle.

This paper presents a fault-tolerant control (FTC) algorithm for four-wheel independently driven and steered (4WID/4WIS) electric vehicle. The Extended Kalman Filter (EKF) algorithm is utilized in the fault detection (FD) module so as to estimate the in-wheel motor parameters, which could detect parameter variations caused by in-wheel motor fault. A motion controller based on sliding mode control (SMC) is able to compute the generalized forces/moments to follow the desired vehicle motion. By considering the tire adhesive limits, a reconfigurable control allocator optimally distributes the generalized forces/moments among healthy actuators so as to minimize the tire workloads once the actuator fault is detected. An actuator controller calculates the driving torques of the in-wheel motors and steering angles of the wheels in order to finally achieve the distributed tire forces. If one or more in-wheel motors lose efficacy, the FD module diagnoses the actuator failures first.

For the vehicles equipped with Electric Power Steering (EPS) system, the friction and damping effect brought by assisted motor and worm gear mechanism influence the return ability and handing stability. In order to eliminate the impacts, it is necessary to add return-to-center control in EPS control strategy. This paper proposes a practical active return-to-center control strategy with steering wheel angle signals based on return state identification. In the strategy, the return state of the steering system is identified quickly according to the two signals steering wheel angle velocity and steering wheel torque. Only under return state, a double closed-loop PID control strategy is carried out to calculate a compensation current to improve the return ability. For validating the proposed strategy, a fine EPS model including BLDC assisted motor is built based on carsim and simulink co-simulation platform.

Electric Power Steering System (EPS) can directly provide auxiliary steering torque via a motor. The motor and the reducer in mechanical system will make the friction torque in steering system larger, as a result, the ability of steering returning will be reduced. Therefore, during the design of EPS system control strategy, an extra active return-to-middle control strategy is needed. For the fact that most of the low-end vehicles equipped with EPS system do not have a steering wheel angle sensor, a control strategy has to work without the datum of steering wheel angle. This paper proposes an active return-to-middle control method without steering wheel angle sensor, based on the estimated aligning torque which is converted to the pinion, and expounds how to determine the steering system current motion state in detail. This control method will work just during the turning condition, so it has no effect on the EPS basic assist characteristics.

Four-wheel independent drive EV is driven by four brushless DC motors which are embedded in the wheel hubs. It enables each wheel's driving torque to be controlled independently. Due to the motors' torque and rotational speed easily measured, as well as the features of fast response and precise control, the EV enjoys obvious advantages over traditional vehicles in acceleration slip regulation. In this paper a novel acceleration slip regulation strategy for four-wheel independent drive EV is studied. The strategy includes a road identification module for the peak value of road adhesion coefficient and a slip regulation logic based on PID algorithm. Through comparing the current wheel slip ratio and the utilized adhesion coefficient with the typical roads' value, the identification module adopts the fuzzy control algorithm to recognize the similarity between the current road and the typical roads. Utilizing the similarity we can calculate the optimal slip ratio of the current road.

A full drive-by-wire electric vehicle, named Urban Future Electric Vehicle (UFEV) is developed, where the four wheels' traction and braking torques, four wheels' steering angles, and four active suspensions (in the future) are controlled independently. It is an ideal platform to realize the optimal vehicle dynamics, the marginal-stability and the energy-efficient control, it is also a platform for studying the advanced chassis control methods and their applications. A centralized control system of hierarchical structure for UFEV is proposed, which consist of Sensor Layer, Identification and Estimation Layer, Objective Control Layer, Forces and Motion Distribution Layer, Executive Layer. In the Identification and Estimation Layer, identification model is established by utilizing neural network algorithms to identify the driver characteristics. Vehicle state estimation and road identification of UFEV based on EKF and Fuzzy Logic Control methods is also conducted in this layer.

Impact torque will be generated on the steering wheel when one tire suddenly blows out on high way, which may cause driver's psychological stress and result in driver's certain misoperations on the car. In this paper, the model of tire blowout vehicle was established; the tire blowout was detected based on the change rate of tire pressure, meanwhile, the rack force caused by tire blowout was estimated through a reduce observer; finally the compensation current was figured out to reduce the impact torque on the steering wheel. Results of simulation tests showed that the control strategy proposed in this paper can effectively reduce the impact torque on the steering wheel and reduce the driver's discomfort caused by tire blowout.