Search Results

Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims

2021-05-06

CURRENT

J1095_202105

This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of wheels for demountable rims and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters ranging from 165.1 to 335.0 mm (6.500 to 13.189 inches). It is up to each hub and/or wheel for demountable rims manufacturer to determine the appropriate test method, accelerated load factor and cycle life requirements applicable to obtain satisfactory service life for a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or wheel for demountable rims developer to modify other parameters as necessary to ensure satisfactory service life for the intended application. It should be noted that this test procedure focuses on fatigue resulting from vehicle loading and cornering forces.

Standard

Wheel End Assembly and Axle Spindle Interface Dimensions - Truck and Bus

2020-02-13

CURRENT

J2475_202002

This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, spindle threads, bearing cones, bearing spacer, seal, and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W.

Standard

Inboard Mounted Disc Brake Rotor/Disc Wheel Hub Interface Dimensions - Commercial Vehicles

2019-09-03

HISTORICAL

J2696_201909

This SAE Recommended Practice establishes dimensions and tolerances for the interface between inboard mounted disc brake rotors and disc wheel hubs. This document is intended for inboard mounted disc brake rotors and disc wheel hubs for Class 5, 6, 7, and 8 commercial vehicles. Special and less-common applications are not covered.

Standard

Wheels/Rims - Military Vehicles Test Procedures and Performance Requirements

2019-06-06

HISTORICAL

J1992_201906

This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For other (non-military) wheels and rims intended for normal highway use on trucks and buses, refer to SAE J267. For wheels intended for normal highway and temporary use on passenger cars, light trucks, and multipurpose vehicles, refer to SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. This document does not cover off-highway or other special application wheels and rims.

Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims

2016-06-30

HISTORICAL

J1095_201606

This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of wheels for demountable rims and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.500 to 13.189 in). It is up to each hub and/or wheel for demountable rims manufacturer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or wheel for demountable rims developer to modify other parameters to obtain satisfactory service life.

Standard

Wheel End Assembly and Axle Spindle Interface Dimensions - Truck and Bus

2014-07-30

HISTORICAL

J2475_201407

This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W.

Standard

Inboard Mounted Disc Brake Rotor/Disc Wheel Hub Interface Dimensions - Commercial Vehicles

2012-05-29

HISTORICAL

J2696_201205

This SAE Recommended Practice establishes dimensions and tolerances for the interface between inboard mounted disc brake rotors and disc wheel hubs. The geometric features described in this document are shown at true position. This document is intended for inboard mounted disc brake rotors and disc wheel hubs for Class 5, 6, 7, and 8 commercial vehicles. Special and less common applications are not covered.

Standard

Wheels/Rims - Military Vehicles - Test Procedures and Performance Requirements

2012-04-23

HISTORICAL

J1992_201204

This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For wheels and rims intended for normal highway use on trucks and buses, see SAE J267. For wheels intended for normal highway use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. This document does not cover off-highway or other special application wheels and rims.

Standard

Disc Wheel Radial Runout Low Point Marking

2011-03-30

CURRENT

J2133_201103

This SAE Recommended Practice provides for standardized steel disc wheel radial runout low point marking. This marking is used for match-mounting tires on wheels to minimize assembly radial force variation. It applies to tubeless 15 degree drop center disc wheels for use on class 5, 6, 7, and 8 commercial vehicles.

Standard

Disc Wheel Radial Runout Low Point Marking

2010-02-15

HISTORICAL

J2133_201002

This SAE Recommended Practice provides for standardized steel disc wheel radial runout low point marking. This marking is used for match-mounting tires on wheels to minimize assembly radial force variation. It applies to tubeless 15 degree drop center disc wheels for use on class 5, 6, 7, and 8 commercial vehicles.

Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims

2009-10-12

HISTORICAL

J1095_200910

This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of wheels for demountable rims and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hub and/or wheel for demountable rims developer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or wheel for demountable rims developer to modify other parameters to obtain satisfactory service life.

Standard

Wheel End Assembly and Axle Spindle Interface Dimensions—Truck and Bus

2008-08-22

HISTORICAL

J2475_200808

This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, U, W, R, N and P.

Standard

Labeling—Disc Wheels and Demountable Rims—Trucks

2001-07-31

HISTORICAL

J179_200107

This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.

Standard

Setting Preload in Heavy-Duty Wheel Bearings

2001-03-01

HISTORICAL

J2535_200103

This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway, disc wheel / outboard drum brake applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.

Standard

Wide Base Disc Wheels and Demountable Rims

2000-04-26

HISTORICAL

J876_200004

This SAE Recomended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheels and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware.

Standard

Wheel End Assembly and Axle Spindle Interface Dimensions—Commercial Vehicles

2000-01-24

HISTORICAL

J2475_200001

This SAE Recommended Practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include bearing cones, bearing spacers, and wheel hubs. This document is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, R, N, and P. SAE configurations FC, FL, K, L, U, and W are not included, but may be added in the future.

Standard

ABS Excitor Ring Location Standardization

1999-10-09

HISTORICAL

J1730_199910

This SAE Recommended Practice is to establish the Antilock Brake System (ABS) sensor interface and envelope dimensions for standardizing the location of the Antilock Brake System (ABS) rings mounted on the inner end of the hub on the following axle designations. a FF front b FL front c L powered rear d R powered rear e U powered rear f W powered rear g N trailer h P trailer

Standard

Disc Wheel/Hub or Drum Interface Dimensions—Commercial Vehicles

1998-08-01

HISTORICAL

J694_199808

This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document.

Standard

Road Vehicles—Wheels for Commercial Vehicles and Multipurpose Passenger Vehicles—Fixing Nuts—Test Methods

1997-12-01

HISTORICAL

J1965_199712

This SAE Recommended Practice applies to nuts as specified in SAE J694 and J1835 used for wheel and demountable rim attachment. Only the test methods necessary to assure proper wheel or rim assembly are specified. Fasteners for less common and special applications are not included.

Standard

DISC WHEEL/HUB OR DRUM INTERFACE DIMENSIONS—COMMERCIAL VEHICLES

1997-07-01

HISTORICAL

J694_199707

This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document.