Search Results

For improving the thermal efficiency and the reduction of hazardous gas emission from IC engines, it is crucial to model the heat transfer phenomenon starting from the intake system and predict the intake air’s mass and temperature as precise as possible. Previously, an empirical equation was constructed using an experimental setup of an intake port model of an ICE, in order to be implemented into an engine control unit and numerical simulation software for heat transfer calculations. The empirical equation was based on the conventional Colburn analogy with the addition of Graetz and Strouhal numbers. Introduced dimensionless numbers were used to characterize the entrance region, and intermittent flow effects, respectively.

In order to get better results in the Formula SAE of Japan, it is necessary to develop a small displacement engine with an ideal fuel consumption rate. Therefore, the authors started to improve an existing engine by combining with glow plug heated sub-chamber and lean burn. Lean burn conditions are usually adopted in gasoline engines, having the advantages of high specific heat ratio, low pump loss, and low cooling loss due to requiring a decreased combustion temperature. The combination of these elements can be expected to vastly improve thermal efficiency and fuel consumption. Unfortunately, however, when the mixture becomes lean, the ignition delay increases, and the flame propagation speed reduces. This leads to an increase in combustion fluctuation. The authors intend to solve this problem by installing a glow plug in a newly designed sub-chamber. This type of device would usually be used to heat the sub-chamber of a diesel engine to solve the cold start problem.

This paper provides the importance of helical coil sub-cooled condenser which has a compact structure, large heat transfer area, and high heat transfer capability in comparison to the straight sub-cooled condenser in the automobile vehicle. The HVAC unit has the largest parasitic load on the engine. Hence, by improving the coefficient of performance of the air-conditioning (A/C) system, the reduction in vehicule emissions is possible. Previous studies explain that there is generation of secondary flow inside the fluid in the circular cross-section of the helical coil. By using the effect of the secondary flow generation, authors tried to enhance the heat transfer rate as it leads to heterogeneous temperature distribution across the periphery of the tube and causes a higher heat transfer. For the purpose of the study, a prototype with a square cross-sectional 2.7 mm × 2.7 mm channel with flat fins towards the outer side has been constructed.

Diesel engines need to optimize the fuel injection timing and quantity of each cycle in the transient operation to increase the thermal efficiency and reduce the exhaust gas emissions through the precise combustion control. The heat transfer from the working gas in the combustion chamber to the chamber wall is a crucial factor to predict the gas temperature in the combustion chamber to optimize the timing and quantity of fuel injection. Therefore, the authors developed both the heat loss and the polytropic index prediction models with the low calculation load and high accuracy. In addition, for the calculation of the heat loss and the polytropic index, the wall heat transfer model was also developed, which was derived from the continuity equation and the energy equation. The present study used a single cylinder diesel engine under the condition of engine speed of 1200 and 1500 rpm, and measured the local wall temperature and the local heat flux of the combustion chamber.

Attribute to high heat transfer rate and less complexity, the Helical coil sub-cooled condenser (HCSCC) can provide the most innovative and unique application for the air conditioning system. In the case of automobiles, reduction in air-conditioning load may diminish the vehicular emission, and power consumption as the air-conditioning load is the most power-consuming components after the engine load. Moreover, to solve the problem, we focus on the helical type heat exchanger. It may play a vital role in reducing the weight and increase the performance of the small engine because of the compact structure and lighter weight. The compressor unit is the most vital component of the refrigeration cycle, but the condenser unit is also one of the most critical devices, and the author tried to reduce the power consumption by enhancing the performance of the condenser.

This paper oriented towards spiral coil sub-cooled condenser (SCSCC) which is used for the automotive air conditioning system. Therefore, the effect of curvature diameter has been carefully measured by CFD as it reduces/intensify the centrifugal force. This centrifugal force is responsible for Dean vortices and leads to the generation of secondary flow inside the refrigerant. By taking advantage of this secondary flow, the performance of the SCSCC can be improved. CFD analysis comprises curvature diameter from 13mm to 110mm, which varied the Dean number from 7577 to 2605. The author tried to evaluate the complicated phenomena that occurred within the SCSCC. However, the turbulent kinetic energy which is one of the critical factors of heat transfer coefficient illustrates 0.009m2/s2 and 0.006m2/s2 for large and small Dean number, respectively, toward the outer side of the channel.

This study proposes a method to calculate the limit of piston ring conformability to deformed bore based on measured gas leakage flow rate through ring-bore gap and calculated gap area using a test device that allows the creation of arbitrary bore deformation. As a result, it was clarified that predicted conformability can be matched with measured value by modifying a constant value in the conformability equation for a single order bore deformation proposed by Dunaevsky and Tomanik et al. Furthermore, it has been confirmed experimentally that the conformability limit index ∑U for the complex bore deformation proposed by Tomanik is valid. Using ∑U, area of gap between piston ring and deformed bore under engine operating condition was calculated to derive the relationship between blow-by gas flow rate.

This paper discusses the compact structure, innovative and unique approach of high performance spiral coil sub-cooled condenser for compact power plant/engine applications. The motivation behind this study is to reduce the engine emission by improving the coefficient of performance for air-conditioning unit. Since the air conditioning system is the most power consumption units after the power plant, so it significantly affects the fuel consumption and the hazardous gas emissions. In the air condition cycle, the condenser unit is addressed as one of the important devices, and thus, the author tried to reduce the energy consumption by improving the performance of the condenser. The most advantage points of this study is to use spiral coil sub-cooled condenser, which elaborates the effect of secondary flow generation inside the fluid and is known as the Dean’s effect.

An empirical equation was developed for modeling the heat transfer phenomena taking place in an intake manifold which included the backflow gas effect. In literature, heat transfer phenomenon at intake system is modeled based on steady flow assumptions by Colburn analogy. Previously, authors developed an equation with the introduction of Graetz and Strouhal numbers, using a port model experimental setup. In this study, to further improve the empirical equation, real engine experiments were conducted where pressure ratio between the intake manifold and engine cylinder were added along with Reynolds number to characterize the backflow gas effect on intake air temperature. Compared to the experimental data, maximum and average errors of intake air temperature estimated from the new empirical equation were found to be 2.9% and 0.9%, respectively.

In the past two decades, internal combustion engines have been required to improve their thermal efficiency in order to limit hazardous gas emissions. For further improvement of the thermal efficiency, it is required to predict the mass of intake air into cylinders in order to control the auto-ignition timing for CI engines. For an accurate prediction of intake air mass, it is necessary to model the heat transfer phenomena at the intake manifold. From this intention, an empirical equation was developed based on Colburn equation. Two new arguments were presented in the derived formula. The first argument was the addition of Graetz number, where it characterized the entrance region thermal boundary layer development and its effect on the heat transfer inside the intake manifold. As the second argument, Strouhal number was included in order to represent intake valve effect on heat transfer.

This paper represents the adaptation of turbo charger to single cylinder 450cc SI engine which is used for the student formula competition. The experiment and 1D engine simulation called as GT-Power were performed to confirm the effect of valve profile, compression ratio and air fuel ratio on the engine performance under the naturally aspirated condition. The maximum valve lift of the intake valves increased 27% and that of the exhaust valves increased 15% as compared with the low profile cam. The compression ratio was increased from 12.3 to 13.5 by changing the piston top land length in order to improve the thermal efficiency. It was confirmed that the torque peak was moved from 6000 rpm to 8000 rpm by changing the valve profile. Furthermore, turbo charger was adapted to the engine as changing the capacity of the turbocharger, the maximum boost pressure and the air fuel ratio.

For further development of the thermal efficiency of SI engines, the robust control of the air-fuel ratio (A/F) fluctuation is one of the most important technologies, because the A/F is maintained at the theoretical constant value, which causes the increase of the catalytic conversion efficiency and the reduction of pollutant emission. We developed the robust controller of the A/F, which is the method to change the fuel injection rate by using the feed-forward (FF) controller considering the heat transfer at the intake system. The FF controller was verified under transient driving conditions for a single cylinder, and the A/F fluctuations were reduced at approximately 84%.

The paper reviews the experimental development of fuel economy of engine powering the 2012 Formula SAE single seat race car of the University of Sophia. The balance of high power and low fuel consumption is biggest challenge of racing engine. It was found that improving the efficiency of engine by supercharging as a way to achieve that. In order to adapt the supercharger for the engine, the important design points are below: It was found that intake air blow-by gas at combustion chamber is increased in low engine speed. To improve that, the valve overlap angle was changed to adopt supercharged engine and improve effective compression ratio. Typically the racing engine demands maximum torque for performance but that does not imply that the air fuel ratio should be rich than theoretical. The point is the maximum torque of the engine is proportional to the amount of air intake. Therefore, supercharged engine is possible to increase the supercharging pressure for bigger torque.

1 Many environmental problems, such as global warming, drain of fuel and so on, are apprehended in all over the world today, and down-sizing is one of the wise ways to deal with these problems. It is significant that a decrease of the engine power must not be produced by using a small displacement engine, so more efficient engine system should be designed to increase the torque with a little fuel. This study achieves an improvement of efficiency for mounting the super charging system on the small displacement engine. As a result, comparing a super charged engine and a naturally aspirated one to drive the same course and laps, fuel consumptions are 2547 [cc] and 3880 [cc], respectively, and an improvement of fuel consumption is 52%. Designing points to mount super charging system is introduced below. 1 It can be forecasted that intake air blow-by gas at the combustion chamber is increased in low engine speed because engine for motor cycle is used.

The experiments were done in order to obtain the fundamental information that would be needed to build a physical model which expresses the heat transfer phenomena in the intake port model and manifold. In the experiments, the heating conditions and the period of the cyclic change of the gas velocity were changed as experimental parameters. In addition to those parameters, the Strouhal number was applied to express oscillating flow. As a result, the heat transfer in the experiments became clear, and the equations were obtained to show the Nusselt number using the Reynolds number, the Graetz number and the Strouhal number.

In order to clarify the diesel fuel spray characteristics inside the cylinder, we developed two novel techniques, which are preparation of same level of temperature and pressure ambient as inside cylinder and quantitative measurement of vapor concentration. The first one utilizes combustion-type constant-volume chamber (inner volume 110cc), which allows 5 MPa and 873K by igniting the pre-mixture (n-pentane and air) with two spark plugs. In the second technique, TMPD vapor concentration is measured by using Laser Induced Exciplex Fluorescence method (LIEF). The concentration is compensated by investigation of the influence of ambient pressure (from 3 to 5 MPa) and temperature (from 550 to 900 K) on TMPD fluorescence intensity. By using two techniques, we investigated the influence of nozzle hole diameter, injection pressure and ambient condition on spray characteristics.

Temperature measurement experiments with intake port model were done to achieve the fundamental information on constructing physical model that expresses the heat transfer phenomena in the intake manifold and intake port. The experiments were done with steady airflow, and the size, shape, heating condition of the port model and mass flow rate were changed as experimental parameters. As the results, it was clear that the developing condition of velocity and thermal boundary layer had greater influence than the shape factor, and the coefficient and the exponent of the equation derived from the relationship between Nusselt number and Reynolds number had great difference from those of generally used Colburn's equation in undeveloped entrance region, but they got closer as developing boundary layer.

In this paper we propose a new multi-functional steering wheel switch for HVAC and audio systems. This new switch has five buttons on the front side of the spoke area and one button with vibration on the backside of it. Drivers can operate either HVAC or audio functions with the front switches, and HVAC or audio mode can be alternatively selected by pressing the back switch. Since different vibration modes are assigned for the HVAC and audio mode, drivers can also easily recognize which function can be operated. By changing the assignment of the mode in this way, the switch can operate more than 10 functions with 6 buttons allocated on the spoke area. Several kinds of evaluations were performed in order to develop this multi-functional switch. At first, to optimize the positions of the buttons, the behaviors of thumbs and fingers were measured. Also the physical workload of the thumb motion and middle fingers' postures was evaluated when subjects operated the switches.

Temperature distribution as the flame propagated and contacted to the wall of the combustion chamber was measured by real-time holographic interference method, which mainly consisted of an argon-ion laser and a high-speed video camera. The experiment was done with a constant volume chamber and propane-air mixture with several kinds of equivalence ratios. From the experimental results, it can be found that the temperature distribution outside the zone from the surface of the combustion chamber to 0.1mm distance could be measured by counting the number of the interference fringes, but couldn't within this zone because of lacking in the resolution of the used optical system. The experimental results show that the temperature distribution when the heat flux on the wall increases rapidly and when the heat flux shows the maximum value are quite different by the equivalence ratio.

The electronic controlled carburetor and ignition system has been developed. In accordance with various working conditions of the engine, the system adjusted corresponding control parameters; air fuel ratio and ignition timing, therefore it could keep the engine working on the optimal conditions. Through analyzing overall performance of the engine based on the experimental data, we had concluded that the specific fuel consumption was improved about 8-10%, and the exhaust emission performance was improved correspondingly after electronic control, the improved ratio was about 10% for HC emission and 97% for CO emission.