Search Results

This course is verified by Probitas Authentication as meeting the AS9104/3A requirements for continuing Professional Development. Why is a design for manufacturing, assembly and automation so important? This introductory course on airframe engineering will cover the importance of design for manufacturing, assembly and automation in aerospace. It will review what the key drivers are for a “good” design and some of the key points for manufacturing and assembly of aircraft components. It will look at how an engineer can combine traditional technologies with new, cutting-edge technologies, to determine the best scenario for success.

This course describes the basic elements of the process for achieving a successful aircraft certification globally once certification by the State of Design has been accomplished. The regulatory framework established under ICAO is presented with discussion of how major countries around the world comply with the ICAO Standards and Recommended Practices (SARPs). The uncertainty of how each country performs validation is a challenge. This course identifies common validation practices and key bilateral agreements which facilitate acceptance of aviation products from one country to another.

The automated vehicle industry has been busy designing, developing, and deploying several self driving vehicles and services in the last few years. However, much of the outcomes and the overall outlook of the vehicle and services, such as robotaxis, are not great. Customers and stakeholders complain that the level of automation is low, mostly SAE Levels 1, 2, and very little of Level 3. It appears that Level 4 is far out in the horizon and many wonder if Level 5 is actually achievable.

Potential regulations surrounding the development, testing and commercial launch of Highly Automated Vehicles and possible liability exposure for the manufacturing and operation of Highly Automated Vehicles are fluid and changing areas, that will continue to evolve over the next several years. The first half of this course reviews where regulations are at the state and federal levels, what actions are currently under consideration, how current regulations will need to change to accommodate HAV’s, and how and when new regulations might be implemented. The second half covers both common law and strict liability and how it may apply to HAV’s.

There is a growing interest in the concept of a smart city and how these advanced technologies will improve the quality of living and make a city more attractive to visitors, commerce and industry. This course fills an unmet need for defining and explaining the relationship between connected and autonomous vehicles (CAVs) and smart city transportation. It is apparent that CAVs will achieve the best results when integrated with current and emerging urban infrastructure for transportation. This course addresses such integration from technology, organizational, policy and business model perspectives.

The concept of a Quality System’s approach to business has been employed successfully and sometimes not so successfully for several decades. The International Organization for Standardization (ISO) has been supplying standards that list the key elements/clauses and requirements for building and implementing Quality Systems for over 30 years. These standards are based on the relatively simple concepts of Total Quality Management (TQM), essential principals of management, and a “Process” approach. These standards have been revised several times over the years to make them more realistic and user friendly.

This course is offered in China only and presented in Mandarin Chinese. The course materials are bilingual (English and Chinese). Currently in the industry, especially within China, product requirement development is more of an experience-based process rather than a scientific methodology. This course addresses this issue and provides a more process-driven method for better requirement development through the Quality Function Deployment (QFD) methodology.  Real industrial examples are used to demonstrate how to systematically convert the voice of the customer data to engineering specifications using QFD.

This course is offered in China only and presented in Mandarin Chinese. There appears to be a significant gap between Chinese and international hybrid technologies in terms of vehicle fuel consumption, system integration, and cost control. This course has been designed to increase an engineers’ knowledge of hybrid transmission development, hybrid system design, and hybrid vehicle powertrain integration. The course focuses on energy efficiency in electric vehicles (EV) and hybrid electric vehicles (HEV) fuel economy while maintaining and improving engineering for optimal power and performance, cost control, and occupant comfort.

This course is offered in China only and presented in Mandarin Chinese. Driving simulator is a key component of automotive interactive design, which can provide objective data to support both the effectiveness of design and user experience. On the other hand, driving simulator and the design of its experiments are major challenges, as improper experiment design will lead to consequences such as failure in identifying designing errors of the interactive design itself.

Advanced Driver Assist System (ADAS) and autonomous vehicle technologies have disrupted the traditional automotive industry with potential to increase safety and optimize the cost of car ownership. Light detection and ranging (LIDAR) sensing, a sensing method that detects objects and maps their distances, is seeing rapid growth and adoption in the industry. However, the sensor requirements and system architecture options continue to evolve. This course will provide the foundation to build LIDAR technologies in automotive applications.

Advanced Driver Assist System (ADAS) and autonomous vehicle technologies have disrupted the traditional automotive industry with potential to increase safety and optimize the cost of car ownership. Among the challenges are those of sensing the environment in and around the vehicle. Infrared camera sensing is seeing a rapid growth and adoption in the industry. The applications and illumination architecture options continue to evolve. This course will provide the foundation on which to build near infrared camera technologies for automotive applications.

This four-hour short course provides an introduction to fluids for aerospace hydraulic systems. Topics covered include an introduction to basics fluid properties, rheology, tribology, and fluid product development. In addition, the history and performance of different classes of fluids are discussed in detail, and specific failure modes such as erosion and sludge formation will be described. Along with an introduction to fluid degradation, information on used oil analysis test methods and interpretation will be provided.

There is been tremendous progress in the application of technology and artificial intelligence to connected and autonomous vehicles. At the same time, there have been considerable advances in data science and data analysis that allows large data sets to be managed for results. This course introduces big data and analytics, focusing on how these will be applied to data generated by autonomous and connected vehicles. These technologies will be explained within the context of a smart city.

This two-day foundational-level course teaches Advanced Concepts of GD&T as prescribed in the ASME Y14.5-2009 Standard. It offers an explanation of complex GD&T topics, such as the expanded use of composite position and profile tolerances, customized datum reference frames, the translation modifier, and applying GD&T to non-rigid parts. You’ll learn about functional dimensioning, form controls, the datum system, additional and complex datum feature types, expanded datum target concepts and usage on restrained parts, simultaneous, and separate requirements.

Led by our senior GD&T professionals with a wide variety of industry background and experience, this one-day GD&T Review and Application course is designed for organizations who have participated in training through SAE but are looking for further clarification on how to apply GD&T best practices to specific organizational drawings. Designed to assist your design teams with highly complex design analysis problems and to support your teams through real world drawing examples, the instructor will review, answer questions, and provide feedback on tolerance analysis and GD&T implementation.

This course is offered in China only and presented in Mandarin Chinese. The course materials are bilingual (English and Chinese). Energy conservation and emission reduction has always been a goal for many countries. Especially since the introduction of China VI Vehicle Emission Standards and CAFC & NEV Credit Regulation, the output of NEVs has grown explosively while accompanied by a large number of car fire burning problems and complaints about the shortening of proclaimed electric-only driving range.

Use of Model-Based Systems Engineering (MBSE) has been growing across industry, extending beyond defense and aerospace to include various commercial enterprises such as automotive and healthcare. Tool vendors are quick to point out benefits of this model-based approach and practices but are not always clear how MBSE benefits can be realized on a project. When deployed successfully, several key considerations should be addressed that maximize the value for a use-case. This four-hour class will discuss the nature and purpose of the MBSE approach and how key information is used for successful MBSE deployment as it relates to Systems Management.

This course is offered in China only and presented in Mandarin Chinese. The course materials are bilingual (English and Chinese). Software technology for airborne and ground-based operations has changed and software development teams frequently need guidance on tools for the development, verification, transformation, testing, modification and control of software programs. Developed in support of DO-178C or CO-278A, RTCA DO-330 explains the process and objectives for qualifying software tools and facilitates the compliance of airborne products.

This course is verified by Probitas Authentication as meeting the AS9104/3A requirements for continuing Professional Development. Reverse engineering has become a common and acceptable practice utilized by many original equipment manufacturers and suppliers. This course focuses on the application of modern technologies used to decode the design details and manufacturing processes of an existing part in the absence of the original design data.  It emphasizes the real-life practice of reverse engineering in the aerospace industry from both scientific and legal points of view.  

This course enables transportation professionals to optimize smart mobility for maximum return within smart cities. It offers a structured introduction to the subjects and makes use of real-life examples, local government, technology solution providers, and consulting. The course integrates insights and understandings related to the best use of technology, best practices, lessons learned, challenges, and opportunities.