Search Results

This paper describes an in-cylinder lean-rich combustion (no-post-injection for rich) switching control approach for modern diesel engines equipped with exhaust-treatment systems. No-post-injection rich combustion is desirable for regeneration of engine exhaust-treatment systems thanks to its less fuel penalty compared with regeneration approaches using post-injections and / or in-exhaust injections. However, for vehicle applications, it is desirable to have driver-transparent exhaust-treatment system regenerations, which challenge the in-cylinder rich-lean combustion transitions. In this paper, a nonlinear in-cylinder condition control system combined with in-cylinder condition guided fueling control functions were developed to achieve smooth in-cylinder lean-rich switching control at both steady-state and transient operation. The performance of the control system is evaluated on a modern light-duty diesel engine (G9T600).

Commercial vehicles are moving in the direction of improving brake thermal efficiency while also meeting future diesel emission requirements. This study is focused on improving efficiency by replacing the variable geometry turbine (VGT) turbocharger with a high-efficiency fixed geometry turbocharger. Engine-out (EO) NOX emissions are maintained by providing the required amount of exhaust gas recirculation (EGR) using a 48 V motor driven EGR pump downstream of the EGR cooler. This engine is also equipped with cylinder deactivation (CDA) hardware such that the engine can be optimized at low load operation using the combination of the high-efficiency turbocharger, EGR pump and CDA. The exhaust aftertreatment system has been shown to meet 2027 emissions using the baseline engine hardware as it includes a close coupled light-off SCR followed by a downstream SCR system.

A new diesel engine system adopting alternative combustion with rich and near rich combustion, and an airflow-dominant control system for precise combustion control was used with a 4-way catalyst system with LNT (lean NOx trap) to achieve Tier II Bin 5 on a 2.2L TDI diesel engine. The study included catalyst temperature control, NOx regeneration, desulfation, and PM oxidation with and without post injection. Using a mass-produced lean burn gasoline LNT with 60,000 mile equivalent aging, compliance to Tier II Bin 5 emissions was confirmed for the US06 and FTP75 test cycles with low NVH, minor fuel penalty and smooth transient operation.

An airflow-dominant control system was developed to provide precise engine and exhaust treatment control with low air fuel ratio alternative combustion. The main elements of the control logic include a real-time state observer for in-cylinder oxygen mass estimation, a simplified packaging scheme for all air-handling and fueling parameters, a finite state machine for control mode switching, combustion control models to maintain robust alternative combustion during transients, and smooth rich/lean switching during lean NOx trap (LNT) regeneration without post injection. The control logic was evaluated on a passenger car equipped with a 4-way catalyst system with LNT and was instrumental in achieving US Tier II Bin 5 emission targets with good drivability and low NVH.

This paper describes a hybrid robust nonlinear control approach for modern diesel engines running low temperature combustion and conventional diesel combustion modes. Using alternative combustion modes has become a promising approach to reduce engine emissions. However, due to very different in-cylinder conditions and fueling parameters for different combustion modes, control of engines operating multiple combustion modes is very challenging. It becomes difficult for conventional calibration / mapping based approaches to produce satisfactory results in terms of engine torque responses and emissions. Advanced control techniques are then demanded to accomplish the tasks. An innovative hybrid control system is designed to track different key engine operating variables at different combustion modes as well as avoid singularity which is inherent for turbocharged diesel engines running multiple combustion modes.

The classical approach to prepare engine exhaust emissions control systems for evaluation and certification is to condition the fresh parts by aging the systems on an engine/dynamometer aging stand. For diesel systems this can be a very lengthy process since the estimated service life of the emissions control systems can be several hundred thousand miles. Thus full useful life aging can take thousands of engine bench aging hours, even at elevated temperatures, making aging a considerable cost and time investment. Compared to gasoline engines, diesel engines operate with very low exhaust gas temperatures. One of the major sources of catalyst deactivation is exposure to high temperature [ 1 ].

For transmission suppliers tooled primarily for producing manual transmissions, retrofitting a manual transmission with actuators and a controller is business viable. It offers a low cost convenience for the consumer without losing fuel economy when compared to torque converter type automatics. For heavy duty truck fleets even the estimated 3% gain in fuel economy that the Automated Manual Transmission (AMT) offers over the manual transmission can result in lower operational costs. This paper provides a case study using a light duty transmission retrofitted with electric actuation for gears and the clutch. A high level description of the control algorithms and hardware is included. Clutch control is the most significant component of the AMT controller and it is addressed in detail during operations such as vehicle launch from rest, launch from coast and launch on grades.

Until recently, U.S. government efforts to dramatically reduce emissions, greenhouse gases and vehicle fuel consumption have primarily focused on passenger car applications. Similar aggressive reductions need to be extended to heavy vehicles such as delivery trucks, buses, and motorhomes. However, the wide range of torques, speeds, and powers that such vehicles must operate under makes it difficult for any current powertrain system to provide the desired improvements in emissions and fuel economy. Hybrid electric powertrains provide the most promising, near-term technology that can satisfy these requirements. This paper highlights the configuration and benefits of a hybrid electric powertrain capable of operating in either a parallel or series mode. It describes the hybrid electric components in the system, including the electric motors, power electronics and batteries.

Cabin air quality is of continuing importance [1]. Contamination of air with particulates or vapors has the potential of affecting the health of passengers and flight crew. Therefore, measures are required to maintain acceptable levels of cabin air quality. One potential source of cabin air contamination is lubricating oils used in the engines. Type II oils are required for the main engines, but Type I or Type II oils can be used for the APU, with Type I recommended by some engine manufacturers for its cold-start properties. Southwest Research Institutes (SwRI®) Department of Emissions Research used an internally developed analytical method called Direct Filter Injection/Gas Chromatograph (DFI/GC™) to analyze for volatile fractions of lubricating oil contaminants on Environmental Control System (ECS) components. Samples of two standard Type II aviation turbine lubricating oils were analyzed with the DFI/GC™ method and their spectra examined.

This paper describes the findings of a laboratory effort to demonstrate improved automotive exhaust emission control with a cold-start hydrocarbon collection system. The emission control strategy developed in this study incorporated a zeolite molecular sieve in the exhaust system to collect cold-start hydrocarbons for subsequent release to an active catalytic converter. A prototype emission control system was designed and tested on a gasoline-fueled vehicle. Continuous raw exhaust emission measurements upstream and downstream of the zeolite molecular sieve revealed collection, storage, and release of cold-start hydrocarbons. Federal Test Procedure (FTP) emission results show a 35 percent reduction in hydrocarbons emitted during the cold-transient segment (Bag 1) due to adsorption by the zeolite.

Recent legislation, including the California Clean Air Act of 1988 and the Federal Clean Air Act Amendment of 1990, includes off-road engines, equipment, and vehicles as targets for new exhaust emissions regulations. The Santa Barbara County Air Pollution Control District in cooperation with EXXON USA is conducting a major Low NOx Demonstration Program including mobile sources, construction equipment, and offshore equipment. As a part of this program, an existing backhoe has been retrofitted with a low NOx engine and demonstrated in the field. This paper discusses the work performed to allow Case model 580 backhoes to be retrofitted with Cummins 4BTAA3.9 on-highway turbocharged diesel engines. A standard production conversion kit can be used to mount the new engines in place of the older existing JI Case engines in some models while other newer models already have 4B3.9 engines. In addition, an air-to-air aftercooler and associated plumbing was designed and installed.

The promising D-EGR gasoline engine results achieved in the test cell, and then in a vehicle demonstration have led to exploration of further possible applications. A study has been conducted to explore the use of D-EGR gasoline engines as a lower cost replacement for medium duty diesel engines in trucks and construction equipment. However, medium duty diesel engines have larger displacement, and tend to require high torque at lower engine speeds than their automobile counterparts. Transmission and final drive gearing can be utilized to operate the engine at higher speeds, but this penalizes life-to-overhaul. It is therefore important to ensure that D-EGR combustion system performance can be maintained with a larger cylinder bore, and with high specific output at relatively low engine speeds.

In this study, the criteria pollutant emissions from a light duty vehicle equipped with Dedicated EGR® technology were compared with emissions from an identical production GDI vehicle without externally cooled EGR. In addition to the comparison of criteria pollutant mass emissions, an analysis of the gaseous and particulate chemistry was conducted to understand how the change in combustion system affects the optimal aftertreatment control system. Hydrocarbon emissions from the vehicle were analyzed usin g a variety of methods to quantify over 200 compounds ranging in HC chain length from C1 to C12. The particulate emissions were also characterized to quantify particulate mass and number. Gaseous and particulate emissions were sampled and analyzed from both vehicles operating on the FTP-75, HWFET, US06, and WLTP drive cycles at the engine outlet location.

Electromagnetic compatibility (EMC) design considerations have a vital role in the proper functioning of the electronic circuits and systems of a modern off-highway vehicle (OHV). Careful planning is needed in developing the electronic systems that operate the various functions and tasks on these vehicles. Incorporation of EMC in a system design gives that system the quality of reliability; that is, the system will have reduced emissions and be less susceptible to radiated and conducted electromagnetic energy. This paper provides ideas, concepts, and guidelines that the designer of OHV control circuitry can use for incorporation of EMC at the beginning of a design project.

An Automatic Tire Inflation System (ATIS), specifically designed for use on commercial long haul trailers, requires modification of the axles to direct air to the tires. The ATIS requires a drilled hole through the axle tube for the installation of a pneumatic fitting. The trucking industry expressed concern about the modification and its impact upon the axle structure, and the general durability of the system over a long period. A three-phase test program was developed and conducted to satisfy the concerns of the industry.

Development of a state of the art, electronically controlled natural gas-fueled engine is detailed in this paper. The engine is a lean burn, turbochargedaftercooled engine controlled by a full authority electronic control system. This system controls fuel metering, spark timing, boost pressure, throttle position, and governing. The control system features closed-loop/adaptive-learn fuel control with feedback provided by a universal exhaust gas oxygen sensor. The development of the engine included development of the control system and other engine components, as well as a substantial amount of steady-state and transient control system calibration work. This effort led to a final engine calibration which provides good efficiency and transient response while meeting CARB ULEV emissions levels.

An Automatic Tire Inflation System (ATIS), specifically designed for use on commercial long haul trailers underwent complete testing and evaluation in 1993/1994.1 Testing and evaluation included a field test of a prototype system and a controlled laboratory evaluation of the Rotary Union which is the only component subject to wear. The testing of the prototype system indicated that design improvements were necessary before the system could be installed in fleet operations. The design improvements were completed and field installation of production ATIS began. The design improvements were intended to improve overall system durability, decrease installation time, to have less effect on the axle structure than the original design, implement the use of SAE or DOT Approved pressure components and increase overall dependability of the system. ATIS systems have now been developed and tested for most domestic trailer axle configurations.

Over twenty prototype hybrid buses and other commercial vehicles are currently being completed and deployed. These vehicles are primarily “series” hybrid vehicles which use electric motors for primary traction while internal combustion engines, or high-speed turbine engines connected to generators, supply some portion of the electric propulsion and battery recharge energy. Hybrid-electric vehicles have an electric energy storage system on board that influences the operation of the heat engine. The storage system design and level affect the vehicle emissions, electricity consumption, and fuel economy. Existing heavy-duty emissions test procedures require that the engine be tested over a transient cycle before it can be used in vehicles (over 26,000 lbs GVW). This paper describes current test procedures for assessing engine and vehicle emissions, and proposes techniques for evaluating engines used with hybrid-electric vehicle propulsion systems.

An Automatic Tire Inflation System (ATIS) specifically designed for commercial use on trailer axles is currently being installed and utilized successfully by trucking companies, the military and owner/operators throughout the U.S. A need exists for an ATIS specifically designed for the drive axles of Class 8 over-the- road tractors. The addition of an ATIS for drive axles will expand automatic tire monitoring capability to all heavily loaded tires of the over-the-road truck/trailer rig. An ATIS for drive axles has been designed, fabricated and tested. Testing and evaluation of the prototype ATIS drive axle system indicates the system can be successfully installed on a typical tractor rig and operated for an extended period without problems. The testing included a 50,000 mile evaluation of the ATIS installed in a laboratory test fixture. The test fixture used stock axle parts and operated at 65 MPH. Environmental testing was conducted at temperatures ranging from -20 to +200 degrees F.

Because of its dominant role in diesel engine performance and emissions, the fuel injection process has become an area of very active research and development. It is now clear that location, shape, rate of development, and mass flow distribution within each fuel jet are all important in controlling fuel air mixing, wall interactions, combustion rate, and the resulting levels of emissions. The objective of this project was to develop an instrument for measurement of the instantaneous fuel mass and momentum distribution in the jets issuing from diesel injection nozzles. The goal was to develop an instrument concept that can be used in the laboratory for fundamental measurements, as well as a quality control system for use in manufacture of the injection nozzles. The concept of the instrument is based on the measurement of the instantaneous momentum of the fuel jet as it impacts on a surface equipped with pressure sensitive elements.