Search Results

Electric power steering systems (EPS) are characterized by high inertia and therefore by a considerably damped transmission behaviour. While this is desirable for comfort-oriented designs, EPS do not provide enough feedback of the driving conditions, especially for drivers with a sporty driving style. The systematic actuation of the electric motor of an EPS makes it possible to specifically increment the intensity of the response. In this context, the road-sided induced forces of the tie rod and the steering rack force provide all the information for the steering system’s response. Former concepts differentiate between use and disturbance information by defining frequency ranges. Since these ranges overlap strongly, this differentiation does not segment distinctively. The presented article describes a method to identify useful information in the feedback path of the steering system depending on the driving situation.

Adoption of high-pressure common-rail (HPCR) fuel systems, which subject diesel fuels to higher temperatures and pressures, has brought into question the veracity of ASTM International specifications for biodiesel and biodiesel blend oxidation stability, as well as the lack of any stability parameter for diesel fuel. A controlled experiment was developed to investigate the impact of a light-duty diesel HPCR fuel system on the stability of 20% biodiesel (B20) blends under conditions of intermittent use and long-term storage in a relatively hot and dry climate. B20 samples with Rancimat induction periods (IPs) near the current 6.0-hour minimum specification (6.5 hr) and roughly double the ASTM specification (13.5 hr) were prepared from a conventional diesel and a highly unsaturated biodiesel. Four 2011 model year Volkswagen Passats equipped with HPCR fuel injection systems were utilized: one on B0, two on B20-6.5 hr, and one on B20-13.5 hr.

Two optical techniques were developed and combined with a CFD simulation to obtain spatio-temporally resolved information on air/fuel mixing in the cylinder of a methane-fueled, fired, optically accessible engine. Laser-induced fluorescence (LIF) of anisole (methoxybenzene), vaporized in trace amounts into the gaseous fuel upstream of the injector, was captured by a two-camera system, providing one instantaneous image of the air/fuel ratio per cycle. Broadband infrared (IR) absorption by the methane fuel itself was measured in a small probe volume via a spark-plug integrated sensor, yielding time-resolved quasi-point information at kHz-rates. The simulation was based on the Reynolds-averaged Navier-Stokes (RANS) approach with the two-equation k-epsilon turbulence model in a finite volume discretization scheme and included the port-fuel injection event. Commercial CFD software was used to perform engine simulations close to the experimental conditions.

A vehicle thermal management system is required to increase the operating efficiency of components, to transfer the heat efficiently and to reduce the energy required for the vehicle. Vehicle thermal management technologies, such as engine compartment encapsulation together with grille shutter control, enable energy efficiency improvements through utilizing waste heat in the engine compartment for heating powertrain components as well as cabin heating and reducing the aerodynamic drag . In this work, a significant effort is put on recovering waste heat from the engine compartment to provide additional efficiency to the components using a motor compartment insulation technique and grille shutter. The tests are accelerated and the cost is reduced using a co-simulation tool based on high resolution, complex thermal and kinematics models. The results are validated with experimental values measured in a thermal wind tunnel, which provided satisfactory accuracy.

Volkswagen is the first automobile manufacturer to supply a passenger car with a direct fuel injection diesel engine to the US market, starting 1996. To meet the stringent US exhaust gas legislation the very successful European 1.9 liter TDI engine has been further developed for the 1996 and 1997 Passat. This TD1 incorporates a number of innovations in advanced diesel technology. Emissions-reducing innovations include: reduced crevice volume higher injection pressures upgraded injection management integrated EGR manifold system EGR cooling diesel catalytic converter This TDI engine configuration is also to be offered in the 1997 Golf and Jetta class and the new Passat in model year 1998. Over the coming years the TDI engine concept will be further optimized by utilizing variations of the above innovations.

In this paper, the experimental and numerical simulation of the flow field in the simplified front wheel arch of a scaled-down VW Phaeton half-model (scale 1:2,5) is presented. For wind tunnel experiments a realistic, rotating wheel model with plexiglass treads (PMMA) was designed. The construction allowed for detailed measurements of the flow field directly at the brake disk by means of the stereoscopic Particle Image Velocimetry (PIV) technique. The formation of the flow structures and the resulting three-dimensional boundary layers on the brake disk are analyzed. Furthermore, the oncoming air flow towards the brake disk and the flow field near the wheel rim openings were investigated. The experimental data is compared with results of Computational Fluid Dynamics (CFD) simulations using the Lattice-Boltzmann based solver Powerflow. The validation shows the potential and the limitations of the numerical approach and indicates areas of further improvement.

This paper presents a complete methodology for performing finite-volume-based detached-eddy simulation for the prediction of aerodynamic forces and detailed flow structures of passenger vehicles developed using the open-source CFD toolbox OpenFOAM®. The main components of the methodology consist of an automatic mesh generator, a setup and initialisation utility, a DES flow solver and analysis and post-processing routines. Validation of the predictions is done on the basis of detailed comparisons to experimental wind-tunnel data. Results for lift and drag are found to compare favourably to the experiments, with some moderate discrepancies in predicted rear lift. Point surface-pressure measurements, oil-streak images and maps of total pressure in the flow field demonstrate the approach's capabilities to predict the fine detail of complex flow regimes found in automotive aerodynamics.

Looking for car weight reduction related to the use of High Strength Steels (HSS) for manufacturing body-in-white components, an innovative application of the high velocity forming techniques has been developed: the Electro Magnetic (EM) calibration and elimination of the spring-back effect (sidewall curl) of High Strength Steel U-channels. Within this paper the initial tests on L and U-shaped parts will be presented. Being the mechanical stiffness the main parameter for improving the coil endurance, the prediction of the coil strains under EM forces is a basic issue, which has been addressed within this study.

This paper summarizes the development of a wireless message from infrastructure-to-vehicle (I2V) for safety applications based on Dedicated Short-Range Communications (DSRC) under a cooperative agreement between the Crash Avoidance Metrics Partners LLC (CAMP) and the Federal Highway Administration (FHWA). During the development of the Curve Speed Warning (CSW) and Reduced Speed Zone Warning with Lane Closure (RSZW/LC) safety applications [1], the Basic Information Message (BIM) was developed to wirelessly transmit infrastructure-centric information. The Traveler Information Message (TIM) structure, as described in the SAE J2735, provides a mechanism for the infrastructure to issue and display in-vehicle signage of various types of advisory and road sign information. This approach, though effective in communicating traffic advisories, is limited by the type of information that can be broadcast from infrastructures.

This paper summarizes the validation of prototype vehicle-to-infrastructure (V2I) safety applications based on Dedicated Short Range Communications (DSRC) in the United States under a cooperative agreement between the Crash Avoidance Metrics Partners LLC (CAMP) and the Federal Highway Administration (FHWA). After consideration of a number of V2I safety applications, Red Light Violation Warning (RLVW), Curve Speed Warning (CSW) and Reduced Speed Zone Warning with Lane Closure Warning (RSZW/LC) were developed, validated and demonstrated using seven different vehicles (six passenger vehicles and one Class 8 truck) leveraging DSRC-based messages from a Road Side Unit (RSU). The developed V2I safety applications were validated for more than 20 distinct scenarios and over 100 test runs using both light- and heavy-duty vehicles over a period of seven months. Subsequently, additional on-road testing of CSW on public roads and RSZW/LC in live work zones were conducted in Southeast Michigan.

A new method has been designed to examine car seats by technical means only, whether they fit summer conditions or not. Test procedures start with the application of a carefully wetted cloth onto the seat to be examined. The test area is then covered by a temperature controlled, electrically heated solid body bloc. This simulates the body temperature and the seat pressure of a real seat user. During test periods of standard three hours, temperature and humidity is measured beneath the test device and in the surrounding air. As an effect of the water impulse the humidity increases under the body bloc. It has been proved that good summer suitability of a car seat is characterised by moderate amount and moderate duration of increased humidity readings. Poor suitability results in higher amount and longer duration of raised humidity. The method is shown to be useful to examine full scale car seats, child safety seats and single design characteristics of car seats as well.

VOLKSWAGEN has conducted a number of investigations on a Multi Fuel Vehicle (MFV), designed for variable fuel operation, to determine the influence of fuel composition and clean fuels on exhaust emissions, mainly on ozone forming potential. Results of the tests indicate a small advantage of Phase II Reformulated Gasoline and a greater one for for methanol fuel M85, compared to today's gasoline. For M85 there is an about 25 % lower ozone forming potential. The most critical components in the exhaust of methanol fueled vehicles (M85) are unburned methanol and formaldehyde, forming more than 60 % of the total ozone forming potential. Therefore improvement of cold start and warmup driving during the first two to three minutes is of great importance, because in this time about 90 % of the mentioned components are formed.

Within the European research programme IDEA (Integrated Diesel European Action), detailed experimental and theoretical studies of the fundamental phenomena of the Diesel engine like flow, injection, mixture formation, auto-ignition, combustion and pollutant formation were carried out to improve knowledge and to set up models for a simulation code. Because this basic research of the Diesel combustion process is very complex and cost intensive, it was carried out jointly by the JRC (Joint Research Committee), an association of European car manufacturers (Fiat, Peugeot SA, Renault, Volvo and Volkswagen). The activities were also subsidized by the Commission of the European Communities and the Swedish National Board of Technical Development. The results of the research work will support the design of even more efficient engines and the further reduction of soot and NOx emissions and will also enable the companies to reduce time and cost in developing new engines.

The spray development, combustion and emissions in a 1.9L optical, four-cylinder, direct-injection diesel engine were investigated by means of pressure analysis, high-speed cinematography, the two-colour method and exhaust gas analysis for various levels of exhaust gas recirculation (EGR), three EGR temperatures (uncontrolled, hot and cold) and three fuels (diesel, n-heptane and a two-component fuel 7D3N). Engine operating conditions included 1000 rpm/idle and 2000 rpm/2bar with EGR-rates ranging from 0 to 70%. Independent of rate, EGR was found to have a very small effect on spray angle and spray tip penetration but the auto-ignition sites seemed to increase in size and number at higher EGR-rates with associated reduction in the flame luminosity and flame temperature, by, say, 100K at 50% EGR.

This paper describes an investigation of one operating point of the transient warmup curve of a gasoline engine. Coolant liquid and oil of this engine have been cooled down to a constant low level in order to perform detailed measurements and an analysis of this particular warmup point. The influence of low coolant temperature, different pressure drop in an air assisted fuel injection system and a variation of ignition angles on specific fuel consumption, exhaust emissions, energy conversion etc. will be shown. The results show that the suggested test procedure (keeping the coolant temperature at a constant low level) provides the possibility to simulate the behaviour of an engine with air assisted fuel injection during warmup. During this warmup period it is desired to run the engine with retarded ignition timing to realize a fast catalyst warmup.

Strategic Materials at Reaction Temperatures (SMART) is an approach used to design washcoat systems for passive 4-way emission control catalysts. Light duty diesel vehicles need to meet the European Motor Vehicle Emissions Group (MVEG) cycle or U. S. Federal test procedure (FTP 75). Emissions that are monitored include hydrocarbon (HC), nitrogen oxides (NOx), carbon monoxide (CO) and total particulate matter (TPM). Low engine-exhaust temperatures (< 200°C during city driving) and high temperatures (> 500-800°C under full load and wide-open throttle) make emission control a formidable task for the catalyst designer Gas phase HC, CO and NOx reactions must be balanced with the removal of the soluble organic fraction for the vehicle to be in compliance with regulations. The SMART approach uses model gases under typical operating conditions in the laboratory to better understand the function of individual washcoat components.

In a joint research project between industrial companies and a number of research institutes, nitrogen oxide conversion in oxygen containing exhaust gas has been investigated according to the following procedure Basic investigations of elementary steps of the chemical reaction Production and prescreening of different catalytic material on laboratory scale Application oriented screening of industrial catalyst material Catalyst testing on a lean bum gasoline engine, passenger car diesel engines (swirl chamber and DI) and on a DI truck engine Although a number of solid body structures show nitrogen oxide reduction by hydrocarbons, only noble metal containing catalysts and transition metal exchanged zeolites gave catalytic efficiencies of industrial relevance. A maximum of 25 % NOx reduction was found in the European driving cycle for passenger cars, about 40 % for truck engines in the respective European test.

In direct-injection gasoline (GDI) engines with charge stratification, minimizing engine-out nitrogen oxide (NOx) emission is crucial since exhaust-gas aftertreatment tolerates only limited amounts of NOx. Reduced NOx production directly lowers the frequency of energy-inefficient catalyst regeneration cycles. In this paper we investigate NO formation in a realistic GDI engine. Quantitative in-cylinder measurements of NO concentrations are carried out via laser-induced fluorescence imaging with excitation of NO (A-X(0,2) band at 248 nm), and subsequent fluorescence detection at 220-240 nm. Engine modifications were kept to a minimum in order to provide results that are representative of practical operating conditions. Optical access via a sapphire ring enabled identical engine geometry as a production line engine. The engine is operated with commercial gasoline (“Super-Plus”, RON 98).

Compatibility has been a passive safety research issue for many years. Great advancements in secondary (passive) safety have been achieved in the last decades through focussing on the self-protection level provided by passenger cars. The next step is to consider the other vehicle involved in the collision as well. Compatibility relates to the simultaneous improvement of both self- and partner- protection. Several tests procedures have been proposed around the world to assess the compatibility of passenger cars. None are considered ready to be implemented. This paper shows that controlling vehicle front-end geometry is the most feasible step to improve both self- and partner-protection. Through this, an increase in the structural interaction potential offered by passenger cars would result. To improve structural interaction, a convergence of front-end structures, to within certain vertical limits, is necessary.

The growing demand for the use of magnesium alloys in the production of automotive powertrain components led to the development of creep resistant diecasting alloys MRI153M and MRI230D. The present paper addresses the main high-pressure die casting parameters, which significantly affect the performance of components, produced of these new alloys. A systematic study was carried out in order to correlate die-casting parameters to the performance of new alloys. The results obtained clearly indicated that optimization of molten metal and die temperatures, injection profile parameters and lubrication mixtures allowed to improve the die castability and service properties of the new alloys and produce high performance components with intricate geometry. This was manifested by production of several practical demonstrators such as gearboxes, oil pans, oil pumps and crankcases.