Search Results

The enhancement of efficiency will play a more and more important role in the development of future (small) internal combustion engines. In recent years, the Atkinson (or Extended Expansion) cycle, realized over the crank drive, attracted increasing attention. Several OEMs have investigated this efficiency-increasing principle in the whole range from small engines up to automotive engines until now. In prior publications, the authors outlined the remarkable efficiency potentials of an Extended Expansion (EE) cycle. However, for an internal combustion engine, a smooth running performance as well as low vibrations and noise emissions are relevant aspects. This is especially true for an Extended Expansion engine realized over the crank drive. Therefore, design measures concerning friction and NVH need to be taken to enable possible series production status. Basically, these measures strongly depend on the reduction of the free mass forces and moments.

Usually the power output of 50 cm₃ two wheelers is higher than necessary to reach the maximum permitted vehicle speed, making engine power restriction necessary. This publication deals with different power restriction strategies for four-stroke engines and their effect on exhaust emissions. Alternative power limitation strategies like EGR and leaning were investigated and compared with the common method of spark advance reduction to show the optimization potential for this certain engine operation conditions. From these tests, a substantial set of data showing the pros and cons in terms of emissions, combustion stability and fuel economy could be derived for each speed limiting technique.

Affordable, efficient and durable catalytic converters for the two and three wheeler industry in developing countries like India are required to reduce vehicle emissions and to maintain them at a low level and therefore to participate in a cleaner and healthier environment. A new generation of metallic substrates with structured foils for catalytic converters has been proven capable of improving conversion behavior even with smaller catalyst size. Specially developed foil structures which transform a laminar exhaust gas flow into a turbulent one, which significantly improve exhaust gas mixing behavior in the catalyst. This publication will deal with the analysis of different metallic substrate foil structures for the catalyst conversion performance for the leading “state of the art” four stroke 150 cm3 motorcycle technology developed for the Asian market.

This publication covers investigations on different 3D CFD models for the description of the spray wall and droplet-fluid interaction and the influence of these models on the mixture formation calculation results. Basic experimental investigations in a spray chamber and a flow tunnel as well as the corresponding 3D CFD simulation were conducted in order to clarify the prediction quality of the physical phenomena of spray-wall and spray-fluid interaction by the simulation. Influencing parameters such as the piston top temperature, piston bowl geometry, soot deposits on the piston top as well as flow velocity are investigated. This paper provides a direct link between the underlying simulation models of the mixture formation and actual real world combustion system development processes - underlining the importance of a close interaction of the model calibration and the development process.

The development process of 2-stroke engines is characterized by limited CFD investigations in combination with long-term development phases on the test bench with high prototype costs. To reduce the costs and to realize shorter development time together with a higher prediction quality of the engine potential, a higher implementation level of 1D and 3D simulation tools into the development process is necessary. This publication outlines the 1D simulation methods in the layout phase of GDI combustion processes of 2-stroke engine categories. By means of conceptual investigations, the demands, the potential and the limits of 1D CFD simulation methodology are defined. Using a comparison between 1D and 3D or 1D/3D coupled simulation methods the limits of solely 1D simulation are shown. For advanced simulation tasks with a higher demand for prediction quality, the entire engine is simulated in 1D, whereas special parts of the engine design are simulated in a 3D model.

The future exhaust emission legislation limits and the procedures for running the test cycles will have an important influence on future range extender concepts. Due to the special steady state operation strategy of the range extender engines, it is possible to create a simple methodology for comparing engine test bench emissions with the emission limits of exhaust gas legislations. Therefore the energy demand of a predefined vehicle was simulated with PHEM, a longitudinal dynamic simulation tool. According to that, the influence of different exhaust gas after treatment systems and preheating options on the tolerated raw emission concentration will be analyzed. With this information, a few chosen range extender engine concepts will be compared concerning their suitability for future exhaust emission legislations. The selection of the range extender concepts was carried out with the methotology of a value benefit analysis.

An efficient and economic method to increase the performance of four stroke engines can be accomplished by utilizing the crankcase supercharging method. The lubrication of the movable parts in the crankcase by mixing the intake air with lubricant leads to a high oil consumption and disadvantages in the emission characteristics. This paper describes parts of a research project with the goal to develop a supercharged four–stroke engine with a closed loop lubrication system for the crank train and the cylinder head. The thermodynamic layout and the development of an oil separating system have been carried out with the help of simulation tools and development work on a flow test bench.

The European emission legislation for two-wheeler vehicles driven by engines of ≤ 50 cm₃ is continuously developing. One of the most important issues in the near future will be the finalization of the European Commission's proposals for future steps in the emissions regulations as well as the verification of the impacts of current standards on the market. To have a basis for the discussion about these topics, the Association for Emissions Control by Catalyst (AECC) with the Institute for Internal Combustion Engines and Thermodynamics of Graz University of Technology (IVT) carried out an extensive test program to show the actual emission situation of state-of-the-art mopeds including mass and number of particulate matter as well as unregulated gaseous components. One of the main goals of these tests was to measure exhaust emissions without any modifications to the engines of standard production vehicles available on the European market.

Electric driving is generally limited to short distances in an emission sensible urban environment. In the present situation with high cost electric storage and long charging duration hybridization is the key to enable electric driving. In comparison to the passenger car segment, where numerous manufacturers are already producing and offering different hybrid configurations for their premium class models, the two wheeler sector is not yet affected by this trend. The main reason for the retarded implementation of this new hybrid technology is its high system costs, as they cannot be covered by a reasonable product price. Especially for the two wheeler class L1e, with a maximum speed of 45 km/h and an engine displacement of less than 50 cm₃, the cost factor is highly important and decisive for its market acceptance, because the majority of vehicles are still low-cost products equipped with simple carbureted 2-stroke engines.

Small combustion engines can be found in various applications in daily use (e.g. as propulsion of boats, scooters, motorbikes, power-tools, mobile power units, etc.) and have predominated these markets for a long time. Today some upcoming competitive technologies in the field of electrification can be observed and have already shown great technical advances. Therefore, small combustion engines have to keep their present advantages while concurrently minimizing their disadvantages in order to remain the predominant technology in the future. Whereas large combustion engines are most efficient thermal engines, small engines still suffer from significantly lower efficiencies caused by a disadvantageous surface to volume ratio. Thus, the enhancement of efficiency will play a key role in the development of future small combustion engines. One promising possibility to improve efficiency is the use of a longer expansion than compression stroke.

Thanks to its unsurpassed power-to-weight ratio, its low package space and low-maintenance design, the loop-scavenged two-stroke engine with conventional mixture preparation is still being used in some sectors of vehicle engineering, such as boat drives, snow mobiles and motor scooters, as well as in hand-held applications. To maintain the potential of the 2-stroke engine for the future it is necessary to take adequate steps against the system-dependent disadvantage of the simple 2-stroke engine, namely that of higher emissions compared to 4-stroke engines. One possible solution is gasoline direct injection. Its more frequent use will increase the production numbers, making it an interesting technology even in the above-mentioned cost-sensitive applications. The current report presents various concepts of direct injection in 2-stroke engines, from air-assisted injection through to high-pressure direct injection, and compares them with traditional techniques of mixture formation.

The demand for high efficiency powertrains in automotive engineering is further increasing, with hybrid powertrains being a feasible option to cope with new legislations. So far hybridization has only played a minor role for L-category vehicles. Focusing on an exemplary high-power L-category on-road vehicle, this research aims to show a new development approach, which combines longitudinal dynamic simulation (LDS) with “Design of Experiments” (DoE) in course of hybrid electric powertrain development. Furthermore, addressing the technological aspect, this paper points out how such a vehicle can benefit from 48V-hybridization of its already existing internal combustion powertrain. A fully parametric LDS model is built in Matlab/Simulink, with exchangeable powertrain components and an adaptable hybrid operation strategy. Beforehand, characterizing decisions as to focus on 48V and on parallel hybrid architecture are made.

As the number of different engine and vehicle concepts for powered-two wheelers is very high and will even rise with hybridization, the simulation of emissions and fuel consumption is indispensable for further development towards more environmentally friendly mobility. In this work, an adaptive artificial neural network based predictive model for emission and fuel consumption simulation of motorcycles operated in real world conditions is presented. The model is developed in Matlab and Simulink and is integrated into a longitudinal vehicle dynamic simulation whereby it is possible to simulate various and not yet measured test cycles. Subsequently, it is possible to predict real drive emissions RDE and on-road fuel consumption by a minimum of previous measurement effort.

The automotive industry has made great efforts in reducing fuel consumption. The efficiency of modern spark ignition (SI) engines has been increased by improving the combustion process and reducing engine losses such as friction, gas exchange and wall heat losses. Nevertheless, further efficiency improvement is indispensable for the reduction of CO2 emissions and the smart usage of available energy. In the previous years the Atkinson Cycle, realized over the crank train and/or valve train, is attracting considerable interest of several OEMs due to the high theoretical efficiency potential. In this publication a crank train-based Atkinson cycle engine is investigated. The researched engine, a 4-stroke 2 cylinder V-engine, basically consists of a special crank train linkage system and a novel Mono-Shaft valve train concept.

In industrial processes and other power generation processes, large amounts of waste heat are often lost to the environment. The conversion of this thermal energy into mechanical work promises a significant improvement in energy-utilization, the efficiency of the overall system and, consequently, cost-effectiveness. Therefore, the use of a Rankine-Cycle is a well-established technical process. A recent research project has investigated a novel expansion machine to be integrated into such an RC-process. Primarily, the present work deals with the fluid dynamic simulation of this expander, which is based on the principle of a rotary piston engine. The aim is to develop, analyze and optimize the process and the corresponding components. Hence, a CFD-model had to be built up, which should correspond as closely as possible to the physical engine.

Legislative regulations and international agreements like the Paris Agreement have been prepared to enforce the effort to reduce the emission of greenhouse gases (GHGs). Greater environmental awareness among customers and introduction of strict environmental regulations have challenged designers to consider the environmental impact of products together with traditional design objectives in the early stages of product design. An important environmental impact factor is the carbon footprint of a product because carbon dioxide (CO2) emissions are a main cause of the global climate change. An early assessment of the product carbon footprint is beneficial because at this stage, design changes are still possible with little effort and at low cost. Actually, there is no detailed methodology for a CO2 impact estimation in the early design phases available and very few researches have been conducted for the special segment of small powertrains.

Amid the increasing demand for higher efficiency in combustion driven handheld tools, the recent developments in electric machine technology together with the already existing benefits of small combustion engines for these applications favor the investigation of potential advantages in hybrid powertrain tools. This concept-design study aims to use a fully parametric, system-level simulation model with exchangeable blocks, created with a power-loss approach in Matlab and Simulink, in order to examine the potential of different hybrid configurations for different tool load cycles. After the model introduction, the results of numerous simulations for 36 to 100 cc engine displacement will be presented and compared in terms of overall system efficiency and overall powertrain size. The different optimum hybrid configurations can show a reduction up to 30 % in system’s brake specific fuel consumption compared to the baseline combustion engine driven model.

Modern small capacity motor scooters make high demands on a trendy vehicle design in combination with a customer friendly handling and multifarious storage space. In addition, increasing engine performance characteristics and high requirements on the vehicle weight call for the development of new vehicle frame concepts. Considering lightweight construction and strength durability, the new concepts are also due to fulfill the boundaries of a low cost production. The driving behavior of a scooter is directly influenced by the interaction of the suspension components, the mounting system of the drive unit and the stiffness of the frame. The present publication treats an assessment of different frame types in the 50cc scooter class by tests and simulation with the target to formulate key data regarding the solidness and stiffness characteristics. Based on these data collection a complete new frame concept has been designed and revised by calculation.

This publication presents the development of a GDI combustion system for high speed - high performance engines. The paper describes the development of the combustion process and its results, the development methodology, covering 1D and 3D CFD simulations, and shows extensive experimental investigations. With 3D CFD simulations the necessary deeper insights in the mixture preparation process of a homogenous GDI combustion system are gained. The findings of the simulation are transferred to an injection and combustion system for a 4-cylinder test engine. The results of the experimental investigations of the 4-cylinder engine equipped with GDI technology show the potential of GDI applications for high performance engines.

In the early phase of an engine development process, the main characteristics of an engine setup, such as lengths, diameter and volumes, are usually defined by means of 1D CFD simulation technologies. Only single flow situations are modeled in 3D due to the high expenditure of time and money. This paper presents a new efficient development methodology using 1D, 3D as well as coupled 1D/3D simulation techniques - the described simulation strategy leads to a more realistic and more comparable reproduction of the flow situation, especially in the critical areas of the simulation domain, while avoiding the restrictions and disadvantages of 1D and 3D simulation. By the use of test bench results of a comparable prototype engine, the quality of the simulation strategy has been successfully verified.