Search Results

During the last years extensive work has been done to design and develop the Closed-Loop Air Revitalization System ARES. The potential of ARES e.g. as part of the ISS ECLSS is to significantly reduce the water upload demand and to increase the safety of the crew by reducing dependence on re-supply flights. The design is adapted to the interfaces of the new base lined Russian MLM module as possible location for a future installation of ARES. Due to the lack of orbital support equipment and interfaces to a waste water bus, to a feed water supply line and due to the availability of only one single vent line it was necessary to make the ARES process water loop as independent as possible from the host vehicle. Another optimization effort was to match the CO2 desorption profile with the available hydrogen flow to achieve a sufficient water recovery performance, while meeting all related safety requirements, minimizing complexity and improving reliability.

ESA has been developing regenerative physicochemical air revitalisation technology for more than 20 years. The effort is now maturing into a flight demonstration experiment which is planned to be located in the Columbus module on ISS. The experiment shall be sized for a crew of three. It will comprise a CO2 concentration assembly, a Sabatier reactor and an electrolyser. The paper describes the adaptation of ARES to the available Columbus interfaces as well as ARES development status, performances, benefits to the ISS and operational agreements with ISS partners.

EADS SPACE Transportation GmbH designed, built and tested a condensate buffer to be located between a Condensing Heat Exchanger (CHX) and a Condensate Water Separator Assembly (CWSA), as part of the ECLSS of the European Columbus Module. Under zero-g conditions, the separation of water from an air-water mixture is always difficult, especially if a passive device is to be used such as the low power consuming Columbus CWSA. The additional buffer volume reduces condensate water peaks reaching the CWSA to a level that excludes an overloading of the CWSA and a release of free water droplets into the air return to the cabin. In the CHX/CWSA system this may only be necessary under worst case operational conditions and with a failure of the qualified hydrophilic coating of the CHX. The buffer design principle was confirmed via prior analyses and on-ground testing. The performance of such a condensate buffer under micro-g conditions was verified during parabolic flights.

During the last years extensive work has been done to design and develop the Closed Loop Air Revitalization System ARES. The potential of ARES for future space exploration missions is to significantly reduce the water upload demand, increase the safety of the crew by reducing dependency on re-supply flights and, due to the launch mass restraints, make future exploration missions to other planets possible. The ARES demonstrator includes the functions of CO2 concentration, CO2 reduction and oxygen generation. Whereas in previous phases ARES was designed to operate in NODE3 of the ISS, this has been changed to an intended ARES operation in the Russian Multifunctional Laboratory Module MLM. This year’s activities concentrated on process optimization of the Carbon Dioxide Removal Assembly (CCA) interaction with the Sabatier Reactor (CRA), extreme conditions testing, life time tests with the Sabatier Reactor and the oxygen generation stack and system testing.

Under an ESA Contract EADS SPACE Transportation GmbH has designed and built an advanced Stainless Steel Condensing Heat Exchanger (CHX) Spare as part of the Environmental Control and Life Support Subsystem (ECLSS) of the European Columbus Module that shall be docked to the ISS in early 2007. Lessons learnt from both, ground and space applications of condensing heat exchangers were to be considered, for risk mitigation, in a CHX alternative design. The slurper section is equipped with a sophisticated capillary suction feature that supports an adequate condensate removal and transport through the slurper holes to the water separator assembly even at low airflow condition. The air fin surface is covered with a hydrophilic coating that did pass qualification for 10 years' exposure to the various contaminants specified respectively determined in the ISS atmosphere so far. The biocidal additive of such coating is qualified for fungus growth prevention, accordingly.

During the last years extensive work has been done to design and develop the Closed Loop Air Revitalization System ARES. The potential of ARES for future space exploration missions is to significantly reduce the water upload demand, increase the safety of the crew by reducing dependency on re-supply flights and due to the launch mass restraints - make future exploration missions to other planets possible. Past years’ activities concentrated on the development of a full-scale demonstrator which was in form, fit, and function comparable to an ‘engineering model’ (EM). Most equipment was off-the-shelf and has been mechanically upgraded to EM standard. The demonstrator includes the functions of CO2 concentration, CO2 reduction and oxygen generation. All components fit into one ISPR. The design minimizes the number of external interfaces in order to achieve a high degree of independence and flexibility. Design baseline for the development was the accommodation in NODE 3 of the ISS.