Search Results

Published NHTSA rulemaking plans propose significant reduction in the maximum stopping distance for loaded Class-VIII commercial vehicles. To attain that goal, higher torque brakes, such as air disc brakes, will appear on prime movers long before the trailer market sees significant penetration. Electronic control of the brakes on prime movers should also be expected due to their ability to significantly shorten stopping distances. The influence upon jackknife stability of having higher performance brakes on the prime mover, while keeping traditional pneumatically controlled s-cam drum brakes on the trailer, is discussed in this paper. A hybrid vehicle dynamics model was applied to investigate the jackknife stability of tractor-semitrailer rigs under several combinations of load, speed, surface coefficient, and ABS functionality.

This paper introduces a new nonlinear model for simulating the dynamics of pneumatic-over-mechanical commercial vehicle braking systems. The model employs an effective systems approach to accurately reproduce forcing functions experienced at the hubs of heavy commercial vehicles under braking. The model, which includes an on-off type ABS controller, was developed to accurately simulate the steer, drive, and trailer axle drum (or disc) brakes on modern heavy commercial vehicles. This model includes parameters for the pneumatic brake control and operating systems, a 4s/4m (four sensor, four modulator) ABS controller for the tractor, and a 2s/2m ABS controller for the trailer. The dynamics of the pneumatic control (treadle system) are also modeled. Finally, simulation results are compared to experimental data for a variety of conditions.

This paper introduces a new series of empirical mathematical models developed to characterize brake torque generation of pneumatically actuated Class-8 vehicle brakes. The brake torque models, presented as functions of brake chamber pressure and application speed, accurately simulate steer axle, drive axle, and trailer tandem brakes, as well as air disc brakes (ADB). The contemporary data that support this research were collected using an industry standard inertia-type brake dynamometer, routinely used for verification of FMVSS 121 commercial vehicle brake standards.

Brake chamber construction allows for a finite stroke for pushrods during brake application. As such, the Federal Motor Carrier Safety Regulations (FMCSRs) mandate maximum allowable strokes for the various chamber types and sizing. Brake strokes are often measured during compliance inspections and post-accident investigations in order to assess vehicle braking performance and/or capability. A number of studies have been performed, and their results published, regarding the effect of brake stroke and function on braking force and heavy truck stopping performance [1] through [4]. All of the studies have relied on a brake supply pressure of 100 pounds per square inch (psi). When brake strokes are measured in the field, following the Commercial Vehicle Safety Alliance (CVSA) procedure, the application pressure is prescribed to be maintained between 90 and 100 psi.

Due to increased speed limits at the state level, NHTSA has pursued additional testing of heavy trucks at higher test maneuver entry speeds. Test results from three vehicles, a Class 7 school bus, a Class 8 truck tractor and a Class 8 straight-truck are presented here. Results are discussed for full treadle straight-ahead stops from 60, 70 and 75 mph. Each vehicle was tested with two different brake configurations. As expected, higher entry speeds resulted in increased stopping distances. Causes for increased stopping distances are briefly discussed. Comparisons show that vehicles in the hybrid configuration (air-disc brakes on steer axle and S-cam brakes on drive axle(s)) had superior stopping performance to the vehicles equipped with traditional S-cam brakes. The vehicles in the hybrid configuration were less susceptible to increased stopping distances from higher entry speeds.

There have been many studies regarding the stability of vehicles following a sudden air loss event in a tire. Previous works have included literature reviews, full-scale vehicle testing, and computer modeling analyses. Some works have validated physics-based computer vehicle simulation models for passenger vehicles and other works have validated models for heavy commercial vehicles. This work describes a study wherein a validated vehicle dynamics computer model has been applied to extrapolate results to higher event speeds that are consistent with travel speeds on contemporary North American highways. This work applies previously validated vehicle dynamics models to study the stability of a five-axle commercial tractor-semitrailer vehicle following a sudden air loss event for a steer axle tire. Further, the work endeavors to understand the analytical tire model for tires that experience a sudden air loss.