Search Results

Standard

Infrared Testing

2018-01-09

CURRENT

J359_201801

The scope of this SAE Information Report is to provide general information relative to the nature and use of infrared techniques for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of infrared testing and as a guide to more extensive references.

Standard

INFRARED TESTING

1991-02-01

HISTORICAL

J359_199102

The scope of this SAE Information Report is to provide general information relative to the nature and use of infrared techniques for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of infrared testing and as a guide to more extensive references.

Standard

Zinc Die Casting Alloys

2017-12-20

CURRENT

J469_201712

Because of the drastic chilling involved in die casting and the fact that the solid solubilities of both aluminum and copper in zinc change with temperature, these alloys are subject to some aging changes, one of which is a dimensional change. Both of the alloys undergo a slight shrinkage after casting, which at room temperature is about two-thirds complete in five weeks. It is possible to accelerate this shrinkage by a stabilizing anneal, after which no further changes occur. The recommended stabilizing anneal is 3 to 6 h at 100 °C (212 °F), or 5 to 10 h at 85 °C (185 °F), or 10 to 20 h at 70 °C (158 °F). The time in each case is measured from the time at which the castings reach the annealing temperature. The parts may be air cooled after annealing. Such a treatment will cause a shrinkage (0.0004 in per in) of about two-thirds of the total, and the remaining shrinkage will occur at room temperature during the subsequent few weeks.

Standard

ZINC DIE CASTING ALLOYS

1989-01-01

HISTORICAL

J469_198901

Because of the drastic chilling involved in die casting and the fact that the solid solubilities of both aluminum and copper in zinc change with temperature, these alloys are subject to some aging changes, one of which is a dimensional change. Both of the alloys undergo a slight shrinkage after casting, which at room temperature is about two-thirds complete in five weeks. It is possible to accelerate this shrinkage by a stabilizing anneal, after which no further changes occur. The recommended stabilizing anneal is 3 to 6 h at 100 °C (212 °F), or 5 to 10 h at 85 °C (185 °F), or 10 to 20 h at 70 °C (158 °F). The time in each case is measured from the time at which the castings reach the annealing temperature. The parts may be air cooled after annealing. Such a treatment will cause a shrinkage (0.0004 in per in) of about two-thirds of the total, and the remaining shrinkage will occur at room temperature during the subsequent few weeks.

Standard

ULTRASONIC INSPECTION

1991-03-01

HISTORICAL

J428_199103

The scope of this SAE Information report is to provide basic information on ultrasonics, as applied in the field of nondestructive inspection. References to detailed information are listed in Section 2.

Standard

Ultrasonic Inspection

2018-01-09

CURRENT

J428_201801

The scope of this SAE Information report is to provide basic information on ultrasonics, as applied in the field of nondestructive inspection. References to detailed information are listed in Section 2.

Standard

MAGNETIC PARTICLE INSPECTION

1991-03-01

HISTORICAL

J420_199103

The scope of this SAE Information Report is to provide general information relative to the nature and use of magnetic particles for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of magnetic particle testing, and as a guide to more extensive references.

Standard

Magnetic Particle Inspection

2018-01-10

CURRENT

J420_201801

The scope of this SAE Information Report is to provide general information relative to the nature and use of magnetic particles for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of magnetic particle testing, and as a guide to more extensive references.

Standard

LIQUID PENETRANT TEST METHODS

1991-03-01

HISTORICAL

J426_199103

The scope of this SAE Information Report is to supply the user with sufficient information so that he may decide whether liquid penetrant test methods apply to his particular inspection problem. Detailed technical information can be obtained by referring to Section 2.

Standard

Liquid Penetrant Test Methods

2018-01-09

CURRENT

J426_201801

The scope of this SAE Information Report is to supply the user with sufficient information so that he may decide whether liquid penetrant test methods apply to his particular inspection problem. Detailed technical information can be obtained by referring to Section 2.

Standard

OIL TEMPERED CHROMIUM-VANADIUM VALVE SPRING QUALITY WIRE AND SPRINGS

1988-12-01

HISTORICAL

J132_198812

This SAE Recommended Practice covers the mechanical and chemical requirements of oil tempered chromium-vanadium valve spring quality wire used for the manufacture of engine valve springs and other springs used at moderately elevated temperatures and requiring high fatigue properties. It also covers the basic material and processing requirements of spring fabricated from this wire.

Standard

OIL-TEMPERED CHROMIUM-VANADIUM VALVE SPRING QUALITY WIRE AND SPRINGS

1994-06-01

HISTORICAL

J132_199406

This SAE Recommended Practice covers the mechanical and chemical requirements of oil-tempered chromium-vanadium valve spring quality wire used for the manufacture of engine valve springs and other springs used at moderately elevated temperatures and requiring high fatigue properties. It also covers the processing requirements of spring fabricated from this wire.

Standard

OIL TEMPERED CHROMIUM - SILICON ALLOY STEEL WIRE AND SPRINGS

1988-12-01

HISTORICAL

J157_198812

This SAE Recommended Practice covers the mechanical and chemical requirements of oil tempered chromium silicon alloy steel wire used for the manufacture of springs requiring resistance to set when used at moderately elevated temperatures. It also covers the basic material and processing requirements of springs fabricated from this wire.

Standard

Sintered Carbide Tools

2018-01-09

CURRENT

J439_201801

This recommended practice covers methods for measuring or evaluating five properties or characteristics of sintered carbide which contribute significantly to the performance of sintered carbide tools. These properties are: hardness, specific gravity, apparent porosity, structure, and grain size. They are covered under separate headings below.

Standard

SINTERED CARBIDE TOOLS

1977-02-01

HISTORICAL

J439_197702

This recommended practice covers methods for measuring or evaluating five properties or characteristics of sintered carbide which contribute significantly to the performance of sintered carbide tools. These properties are: hardness, specific gravity, apparent porosity, structure, and grain size. They are covered under separate headings below.

Standard

SINTERED CARBIDE TOOLS

1977-02-01

HISTORICAL

J439A_197702

This recommended practice covers methods for measuring or evaluating five properties or characteristics of sintered carbide which contribute significantly to the performance of sintered carbide tools. These properties are: hardness, specific gravity, apparent porosity, structure, and grain size. They are covered under separate headings below.

Standard

OIL TEMPERED CARBON STEEL SPRING WIRE AND SPRINGS

1988-12-01

HISTORICAL

J316_198812

This specification covers the mechanical, chemical, and dimensional requirements of oil tempered carbon steel spring wire used in the automotive and related industries. It is especially intended for the manufacture of mechanical springs and wire forms which are not subjected to a large number of high stress cycles. Class I wire is intended for moderate stress and Class II for higher stress level applications. This specification also covers the basic material and heat treat requirements for springs fabricated from this wire.

Standard

OIL TEMPERED CARBON STEEL VALVE SPRING QUALITY WIRE AND SPRINGS

1988-12-01

HISTORICAL

J351_198812

This specification covers the physical and chemical requirements of oil tempered carbon steel valve spring quality wire used for the manufacture of engine valve springs and other springs requiring high-fatigue properties. This specification also covers the basic material and processing requirements of springs fabricated from this wire.

Standard

OIL-TEMPERED CARBON-STEEL VALVE SPRING QUALITY WIRE AND SPRINGS

1994-06-01

HISTORICAL

J351_199406

This SAE Recommended Practice covers the physical and chemical requirements of oil-tempered carbon-steel valve spring quality wire used for the manufacture of engine valve springs and other springs requiring high-fatigue properties. This document also covers the basic processing requirements of springs fabricated from this wire.

Standard

OIL-TEMPERED CARBON-STEEL SPRING WIRE AND SPRINGS

1994-06-01

HISTORICAL

J316_199406

This SAE Recommended Practice covers the mechanical, chemical, and dimensional requirements of oil-tempered carbon-steel spring wire used in the automotive and related industries. It is especially intended for the manufacture of mechanical springs and wire forms which are not subjected to a large number of high stress cycles. Class I wire is intended for moderate stress and Class II for higher stress level applications. This document also covers the processing requirements for springs fabricated from this wire.