Search Results

A simulation technology has been developed to enable prediction of galvanic corrosion in chassis parts where two different materials, iron and aluminum, come into contact with each other. When polarization curves representing a corrosive environment are input, this simulation technology calculates the corrosion current to flow and outputs the volume of aluminum corrosion to be formed near the iron-aluminum interface. The simulation makes it possible to predict the depth of corrosion that may occur in automobiles in the market.

Honda has developed an “Independent Left and Right Rear Toe Control System” that can achieve stable cornering performance and agile handling. We believe the issue that should be resolved in the next generation of ESC is the expansion of stability and agility into the general operation area. We examined how to accomplish this aim, and control of the independent rear toe angle was decided to be an appropriate method. In addition, a method for mounting the system without using a dedicated suspension was proposed. If left and right toe angles can be controlled independently, toe angle control and normal 4WS control become possible at the same time. In this paper, we will discuss the fundamental principle of independent toe angle control and the system configuration. Also, “INOMAMA Handling” (at driver's will) achieved by this system, as well as the fun and safe driving that are achieved as a result will be shown.

In this research, a three degree-of-freedom (DOF) rack-type electric-based power steering (EPS) model is developed. The model is coupled with a three DOF vehicle model and includes EPS maps as well as non-linear attributes such as vibration and friction characteristics of the steering system. The model is simulated using Matlab's Simulink. The vibration levels are quantified using on-vehicle straight-line test data where strain-gauge transducers are placed in the tie-rod ends. Full vehicle kinematic and compliance tests are used to verify the total steering system stiffness levels. Frequency response tests are used to adjust tire cornering stiffness levels as well as the tire dynamic characteristics such that vehicle static gain and yaw natural frequency are achieved. On-center discrete sinusoidal on-vehicle tests are used to further validate the model.

Recently vehicle development timeline is becoming shorter, so there is an urgent need to be able to develop vehicles with limited resources. This means the efficiency of the body structure development process must be improved. Specifically it is important to reduce the amount of design re-work required to meet performance targets as this can have a large influence on the body development time. In order to reduce the afore mentioned design re-work, we developed simple calculation models to apply a “V-Flow Development Process” to the preliminary stage design of the automobile body structure. The “V-Flow” advantages are as follows: (1) simple and easy to use, (2) defects are found at early stage, (3) avoids the downward flow of the defects. The advantage of preliminary stage design is that there is design flexibility since not many specifications have been determined yet.

The development and calibration of stress state-dependent failure criteria for advanced high-strength steel (AHSS) and aluminum alloys requires characterization under proportional loading conditions. Traditional tests to construct a forming limit diagram (FLD), such as Marciniak or Nakazima tests, are based upon identifying the onset of strain localization or a tensile instability (neck). However, the onset of localization is strongly dependent on the through-thickness strain gradient that can delay or suppress the formation of a tensile instability so that cracking may occur before localization. As a result, the material fracture limit becomes the effective forming limit in deformation modes with severe through-thickness strain gradients, and this is not considered in the traditional FLD. In this study, a novel bending test apparatus was developed based upon the VDA 238-100 specification to characterize fracture in plane strain bending using digital image correlation (DIC).

This study developed technology for simultaneously welding heterogeneous resin tubes in order to weld and integrate resin tubes with two different specifications (low temperature and high temperature). The aim of integration was cost and weight reduction. The cost reduction due to reducing the number of parts exceeded the increase in material cost due to a change to resin materials. Base material fracture of the resin tubes was set as the breaking format condition, and the welding parameters of the joint part rotations and the friction time between the joint part and the resin tubes were specified as the weld strength judgment standard. In addition, the fused thickness determined by observing the cross-section after welding was specified as the weld quality judgment standard. The range over which weld boundary peeling does not occur and weld strength is manifest was clarified by controlling the welding parameters and the fused thickness.

The SAE Fuel Cell Vehicle (FCV) Safety Working Group has been addressing FCV safety for over 9 years. The initial document, SAE J2578, was published in 2002. SAE J2578 has been valuable as a Recommended Practice for FCV development with regard to the identification of hazards and the definition of countermeasures to mitigate these hazards such that FCVs can be operated in the same manner as conventional gasoline internal combustion engine (ICE)-powered vehicles. SAE J2578 is currently being revised so that it will continue to be relevant as FCV development moves forward. For example, test methods were refined to verify the acceptability of hydrogen discharges when parking in residential garages and commercial structures and after crash tests prescribed by government regulation, and electrical requirements were updated to reflect the complexities of modern electrical circuits which interconnect both AC and DC circuits to improve efficiency and reduce cost.

The SAE FCV Safety Working Group has been addressing fuel cell vehicle (FCV) safety for over 8 years. The initial document, SAE J2578, was published in 2002. SAE J2578 has been valuable to FCV development with regard to the identification of hazards and the definition of countermeasures to mitigate these hazards such that FCVs can be operated in the same manner as conventional gasoline internal combustion engine (ICE)-powered vehicles. J2578 is currently being updated to clarify and update requirements so that it will continue to be relevant and useful in the future. An update to SAE J1766 for post-crash electrical safety was also published to reflect unique aspects of FCVs and to harmonize electrical requirements with international standards. In addition to revising SAE J2578 and J1766, the Working Group is also developing a new Technical Information Report (TIR) for vehicular hydrogen systems (SAE J2579).

In this study the surface of the bodies being impacted against each other are treated with special speckled paints. A stereophotogrammetric system employing two high speed cameras tracks x,y,z coordinate values during impact. The data is then converted to transient local deformation vectors and strain tensors of the local area on the plastics component being impacted. The camera can also capture displacement vectors of an impactor, a guided or free-flight projectile. Various measurement signals on the projectile and parts are fed into signal processors. These raw data are then processed by a software, specially developed by BASF, for various output data that can be correlated with the corresponding output from the CAE (Computer Aided Engineering) simulations, such as energy during crash processes, real time history of stress and strain on the plastic components.

Exhaust catalyst deactivation in small, handheld, 2-stroke engines is an issue that is faced quite frequently in efforts to improve or maintain catalyst performance but reduce cost. Fresh catalyst performance is rarely an issue, however, sustaining this performance for the specified useful life period of 50, 125, or 300 hours is where challenges start to arise. Our program goal was to develop and demonstrate a commercially viable catalyst which is capable of meeting regulatory and internal requirements with a deterioration factor (DF) near or below 1.0 over a 300 hour useful life period. A secondary objective was to utilize decreased quantities of platinum group metals (PGM) to reduce the cost relative to our reference catalyst. To achieve this, our focus was to reduce poisoning caused by exhaust byproducts and exhaust borne contaminants through a collaboration of catalyst advances and exhaust system design.

The SAE Fuel Cell Vehicle (FCV) Safety Working Group has been addressing FCV safety for over 10 years. The initial document, SAE J2578, was published in 2002. SAE J2578 has been valuable as a Recommended Practice for FCV development with regard to the identification of hazards associated with the integration of hydrogen and electrical systems onto the vehicle and the definition of countermeasures to mitigate these hazards such that FCVs can be operated in the same manner as conventional gasoline internal combustion engine (ICE)-powered vehicles. An update to SAE J1766 for post-crash electrical safety was also published in 2008 to reflect unique aspects of FCVs and to harmonize electrical requirements with international standards. In addition to SAE J2578 and J1766, the SAE FCV Safety Working Group also developed a Technical Information Report (TIR) for vehicular hydrogen systems (SAE J2579).

The CAE method to predict the vibration transfer function of the hydraulic engine mount on a vehicle with sufficient precision and calculation time without prototype cars was developed. The transfer function is given in the following steps. First, rubber deformation form under the power train weight loaded must be predicted. It’s obtained by using a reduction model of an engine mount, as a unit, which doesn’t have its fluid sealed inside, with the technique to get the static spring characteristics in a non-linear relationship. Second, Young’s modulus and structural damping coefficient for the deformed rubber must be given. As for these characteristics, ignoring the relations between these values and strain, the constant values are used. This considerably reduces computation time and model size. Next, the reduction model and the fluid model have must be combined to express actual product. In this step, coupled analysis for fluid and structure is used.

While the microcellular urethane is widely known in the automotive industry for its use in jounce bumpers, its use in Noise Vibration Harshness (NVH) applications is often not as well recognized. Even though there are some NVH parts in the market, rubber still dominates it. The objective of this paper is to demonstrate the material properties of MCU and their relevance for NVH applications in chassis and suspension components. It will also demonstrate the importance of package design to suit the use of the MCU material. This is especially important to not only achieve the best performance but also keep overall cost and weight under control. Several application types will be introduced with general design suggestions. A detailed design guideline for these applications is not part of this paper. Each application has a large variety of parameters to be considered in the design. They need to be selectively applied based on customer performance targets.

Practical evaluation and reduction of edge cracking are two challenging issues in stamping AHSS for automotive body structures. In this paper, the effects of the shear clearance and shear rake angle on edge cracking were investigated with three different grades of AHSS; TRIP780, DP 980, and DP 1180. Five different shear clearances, between 5% and 25% of material thickness, were applied to the flexible shearing machine to generate samples for the half specimen dome test (HSDT). The shear loads and the shear edge quality were thoroughly characterized and compared. The HSDT created the edge forming limits as compared to the base material forming limit diagram. The load-displacement curve was acquired by the load-cell and the strain distribution was measured using a digital image correlation (DIC) system during the dome test.

The effect of engine operating conditions on the formation of combustion chamber deposits has been studied by varying the driving cycle used in a series of vehicle tests aimed at measuring the CCD formation tendencies of different multifunctional fuel detergent additives. It was found that at higher engine temperatures it is not possible to easily differentiate the performance of different additives and that low load and low speed conditions should be chosen when testing additives for CCD control. The data obtained suggest that there is a direct correlation between the decomposition temperature of additive components as measured by thermogravimetric analysis (TGA) and their CCD formation tendencies. Of the various carrier fluids surveyed, materials based on alkyl oxides seem to perform the best in controlling CCD formation.

Automotive manufacturers across the world have experienced the saturation of demand in the mature markets. Foraying into the emerging markets of India and China brings a mix of opportunities and challenges. These economies with 15%+ rising consumer demand, 7%+ rise in per-capita income and a passenger car density less than 1/8 of mature markets, hold promise of sustaining double-digit growth of vehicle sales. But the challenges are immense. Ultra-low margins of OEMs, lack of transportation infrastructure, Low level of maturity of funding operations, fragmented demand, import restrictions and mandatory export obligations pose serious constraints to non-linear growth. HONDA (Honda Siel Cars India Limited), a subsidiary of Honda Motor Corporation, Japan has developed the next generation supply chain with a strategy cognizant of the global opportunities and the local limitations which such emerging economies present.

This paper presents experimental results of a 10.6L, three-cylinder opposed-piston (OP) operating on diesel fuel designed for heavy duty (Class 8) operation. The paper will describe the engine configuration and calibration of both catalyst light-off and high efficiency modes. Analysis based on measured results show the engine can comply with all 2027 California Air Resourced Board (CARB) and Environmental Protection Agency (EPA) requirements for CO2 and criteria emissions. Due to the ability of the OP Engine to combine low oxides of nitrogen (NOX) flux with high exhaust enthalpy for early catalyst light off, the engine can meet all 2027 CARB and EPA NOX standards with a current, state of the art conventional underfloor aftertreatment system. No additional emissions control technology is required.

An investigative group set up under the auspices of the CEC (Coordinating European Council) collected data on combustion chamber deposits (CCD), ASTM unwashed gum (UWG) results and the thermogravimetric analysis (TGA) of these gums for different fuels from many different sources. The analysis of this data shows that UWG cannot and does not predict CCD. It is not possible to use UWG or any aspect of its behaviour in the TGA to assess the CCD-forming tendency of randomly chosen fuels.

Deposits on engine parts, and in particular in combustion chambers of modern engines are causing increasing concern in the automobile industry. Highly sophisticated engine management systems make effects on emissions or performance obvious as outgassing of unburned hydrocarbons or variation of spark advance. Reduced mean heat flux away from the cylinder influences engine thermodynamics. Extreme deposits may cause noise increase by carbon rap. A special form of combustion chamber deposits, well known under the synonym spark plug fouling, is a carbon needle on spark plugs, which can cause the total damage of the catalysts (Japanese Industrial Standard D 1606: Adaptability Test Code of Spark Plug for Automobiles) The Co-ordinating European Council for the development of performance tests for transportation fuels, lubricants, and other fluids (CEC) started the development of a new performance test in 1994.

In order to determine the seizure limit of the main bearings of passenger vehicles under actual operating conditions, evaluations were conducted in environments containing noise factors (Various factors which designer cannot adjust and which make function vary were defined as noise factors in this paper.) [1,2] It was shown that noise factors have an effect on seizure limit performance in relation to performance under ideal test conditions (test conditions in which no noise is present). In relation to oil properties, the results showed that a reduction in viscosity as a result of dilution affected seizure limit performance. In relation to the shape of the sliding sections of the test shaft, seizure limit performance declined in a shaft in which the central section was swollen (“convex shaft” below).