Search Results

With growing demands for better fuel economy and reduced carbon emissions there is a need for smaller and more fuel efficient engines. At the same time, to improve passenger comfort there are also demands placed on improved vehicle quietness [1]. A Homogeneous Charge Compression Ignition (HCCI) system or a higher compression ratio system can be used to obtain better fuel economy but the enhanced combustion rate causes an increase in engine vibration in the medium to high frequency range [2, 3]. To ensure vehicle quietness, this issue of structure-borne noise that is transmitted from the engine mounts to the body must be addressed. In this paper a simple anti-vibration active mount system is introduced that can significantly reduce structure-borne noise at medium to high frequencies. This is achieved by adding mass to the insulator which leads to resonance at lower frequencies, in order to obtain double anti-vibration performance.

Cell balancing is a key function of battery management system (BMS) that is implemented to maximize the battery's available capacity and service life. The increasing demand of larger and better performance pack has raised the need to investigate the various cell balancing techniques so that the energy of the battery can be fully realized. In this work we develop a phenomenological model in order to quantify the benefits of passive balancing and active balancing. The electrical response of a model pack consisting of serially connected lithium ion cells is simulated with Matlab. The effects of the variance of cell capacity, internal resistance, self-discharge rates, pack configuration and size are studied. The possible optimization rooms for implementing passive and active balancing are suggested.

This paper describes the performance evolution and key breakthroughs of the world's first one-motor two-clutch (1M2CL) parallel full hybrid system without a torque converter that was developed and implemented on a hybrid luxury sedan in November 2010. The high potential of this hybrid system was brought out further to improve fuel economy without sacrificing acceleration performance. The resultant second generation of the 1M2CL parallel full hybrid system was applied to a hybrid premium sports sedan in August 2013. In order to improve these performance attributes, the following key technical measures were adopted: 1 Motor torque during the EV mode was increased to expand the EV drive region. 2 Maximum motor torque and battery power at engine startup were boosted to reduce the engine start time. 3 Integrated control of the motor and clutches was improved. 4 Mechanical efficiencies were improved for higher fuel economy.

The failure modes of gas metal arc welds in notched lap-shear specimens of high strength low alloy (HSLA) steel are investigated. Notched lap-shear specimens of gas metal arc welds were first made. Quasi-static test results of the notched lap-shear specimens showed two failure locations for the welds. The specimens cut from coupons with shorter weld lengths failed near the weld root whereas the specimens cut from coupons with longer weld lengths failed near the weld toe. Micro-hardness tests were conducted in order to provide an assessment of the mechanical properties of the base metal, the heat affected zone, and the weld metal. In order to understand the failure modes of these welds, finite element models were developed with the geometric characteristics of the weld metals and heat affected zones designed to match those of the micrographs of the cross sections for the long and short welds.

In this paper, mode I and mode II stress intensity factor solutions for gas metal arc welds in single lap-shear specimens are investigated by the analytical stress intensity factor solutions and by finite element analyses. Finite element analyses were carried out in order to obtain the computational stress intensity factor solutions for both realistic and idealized weld geometries. The computational results indicate that the stress intensity factor solutions for the realistic welds are lower than the analytical solutions for the idealized weld geometry. The computational results can be used for the estimation of fatigue lives in a fatigue crack growth model under mixed mode loading conditions for gas metal arc welds.

Lithium plating is an important failure factor for lithium ion battery with carbon-based anodes and therefore preventing lithium plating has been a critical consideration in designs of lithium ion battery and battery management system. The challenges are: How to determine the charging current limits which may vary with temperature, state of charge, state of health, and battery operations? Where are the optimization rooms in battery design and management system without raising plating risks? Due to the complex nature of lithium plating dynamics it is hard to detect and measure the plating by any of experimental means. In this work we developed an electrochemical model that explicitly includes lithium plating reaction. It enables both determination of plating onset and quantification of plated lithium. We have studied the effects of charging pulses on homogenous plating in order to provide guidance for lithium ion battery design in hybrid applications.

A new highly biofidelic side impact dummy, the WorldSID 50th percentile male, has been developed under the supervision of the International Organization for Standardization in order to harmonize a number of existing side impact dummies in one single dummy. Momentum is growing for using the WorldSID in safety tests in the EU and the US. In the present study, two Euro-NCAP pole side impact tests were conducted to compare ES-2 and WorldSID responses in a mid-size SUV with respective seating positions as stipulated in the Euro-NCAP test conditions and fitted with the same side airbag. It was found that, compared with ES-2, the chest, abdomen and pelvis accelerations of WorldSID are more sensitive to variation in the applied external load transmitted by the deployed side airbag and door intrusion.

Implementation of appropriate safety measures, either from the viewpoint of a vehicle or the society or the infra-structure, it is an important issue to clearly understand the multi-dimension complicated real world accident scenarios. This study proposes a new method to easily capture and to extract the essence of such complicated multi-dimension mutual relationship by visualizing the results of SOM (Self Organizing Map). The FARS data from 2010 is used to generate a dataset comprised of 16,180 fatal passenger car drivers and 48 variables. The 16,180 fatal drivers were clustered using hierarchy cluster analysis method and mapped into a two-dimensional square with one dot representing one fatal driver using SOM.

This study assessed the primary involved physical components attributed to the head and face injuries of child occupants seated directly adjacent to the stuck side of a vehicle in a side impact collision. The findings presented in this study were based upon analysis of the National Automotive Sampling System/Crashworthiness Data System (NASS/CDS) for the years 1993–2007. Injury analysis was conducted for those nearside child occupants aged between 1–12 years-old. The involved children were classified as toddler-type, booster-type, or belted-type occupants. These classifications were based upon the recommended restraint system for the occupant. Injury mechanisms were assessed for the child occupants in each of the three groups. A detailed study of NASS/CDS cases was conducted to provide a greater understanding of the associated injury mechanisms.

Tailored closed sections were created by Orbital Laser Welding tube sections from round steel tubes with differing thicknesses (1 mm wall joined to a 2 mm wall). The tubes were 38 mm outer diameter and constructed from high strength low alloy (HSLA) steel (E235 +c; 10308 per EN10305-1). The tailored closed sections were subjected to compressive and torsion loading conditions to assess the strength of the Orbital Laser Weld. The Orbital Laser Weld was found to have higher strength than the base materials and the performance of the tailored closed section was limited by the thinner section of tube. Results of this study enable automotive seating structures to be optimized for performance while minimizing mass and cost.

Power limit estimation of a lithium-ion battery system plays an important balancing role of optimizing the battery design cost, maximizing for power and energy, and protecting the battery from abusive usage to achieve the intended life. The power capability estimation of any given lithium-ion battery system is impacted by the variability of many sources, such as cell and system components resistance, temperature, cell capacity, and real time state of charge and state of health estimation errors. This causes a distribution of power capability among battery packs that are built to the same design specification. We demonstrated that real time power limit estimation can only partially address the system variability due to the errors introduced by itself. Integrating feedback control algorithms with the lithium-ion battery model maximizes the battery power capability, improves the battery robustness to variabilities, and reduces the real time estimation errors.

High-voltage nanosecond gas discharge has been shown to be an efficient way to ignite ultra-lean fuel air mixtures in a bulk volume, thanks to its ability to produce both high temperature and radical concentration in a large discharge zone. Recently, a feasibility study has been carried out to study plasma-assisted ignition under high-pressure high-temperature conditions similar to those inside an internal combustion engine. Ignition delay times were measured during the tests, and were shown to be decreasing under high-voltage plasma excitation. The discharge allowed instant control of ignition, and specific electrode geometry designs enabled volumetric ignition even at high-pressure conditions.

The 12 V advanced start stop systems can offer 5-8% fuel economy improvement over a conventional vehicle. Although the fuel economy is not as high as those of mild to full hybrids, its low implementation cost makes it an attractive electrification solutions for vehicles. As a result, the 12 V advanced start stop technology has been evolving fast in recent years. On one hand, battery suppliers are offering a variety of energy storage solutions such as stand-alone lead acid, stand-alone LFP/Graphite, dual batteries of lead acid parallel with NMC/LTO, LMO/LTO, NMC/Graphite, and capacitors, etc. For dual battery solutions, the architecture also varies from passive parallel connection to active switching. On the other hand, OEM are considering to leverage a lot more use out of traditional 12 V SLI (start, light, and ignition) for functions such as power steering, air conditioning, heater, etc.

A correct prediction of the initial stages of the combustion process in SI engines is of great importance to understand how local flow conditions, fuel properties, mixture stratification and ignition affect the in-cylinder pressure development and pollutant formation. However, flame kernel growth is governed by many interacting processes including energy transfer from the electrical circuit to the gas phase, interaction between the plasma channel and the flow field, transition between different combustion regimes and gas expansion at very high temperatures. In this work, the authors intend to present a comprehensive, multi-dimensional model that can be used to predict the initial combustion stages in SI engines. In particular, the spark channel is represented by a set of Lagrangian particles where each one of them acts as a single flame kernel.

This paper describes a newly developed electrified powertrain that incorporates various energy-saving improvements and is intended for use on a 2013 model year EV. Based on a 2011 model year EV that was specifically designed and engineered as a mass-produced EV, this powertrain integrates the traction motor, inverter and charging unit to achieve a smaller, lighter package for expanding application to more vehicles. Integration of the motor and inverter in particular reduced the part count for enhanced assembly ease, in addition to reducing heat transfer, noise and vibration. The specific features described in the paper are the three points below. Improving the layout of the inverter parts in order to downsize and integrate the inverter with the motor. Reducing the transfer of heat from the motor to the inverter. Reducing the excitation forces of the motor and optimizing the inverter for noise and vibration.

Occupied seat vibration transfer functions can be used to gauge the ability of a seat system to isolate an occupant from annoying road vibrations. Automotive interior suppliers measure occupied seat vibration transfer functions (transfer functions with a person in the seat) to determine how seat system designs will affect ride comfort. The wide range of physiological dynamic properties among potential test occupants often contributes to a wide range of transfer function measurements for any seat system. This paper evaluates the performance of two approaches to reduce transfer function measurement variation due to multiple test occupants. Reduction of measurement variation can lead to tighter statistical confidence bands for measurements taken with a given number of test occupants. Alternatively, it can lead to a reduction in the number of test occupants required for measurements to fall within a given confidence band.

The microhybrid electric vehicle (MHEV) has increasingly received attention since it holds promise for significant increases in fuel economy vs. traditional gasoline vehicles at a lower price point than hybrid vehicles. Passive parallel connection of the traditional 12V lead acid battery and a high power lithium ion battery has been identified as a potential architecture that will facilitate fuel economy improvements with minimal changes to the electrical network. Enabling a passive dual-battery connection requires a design match between the two batteries, including characteristics such as battery size and resistance, so that the performance can be optimized. In this work we have developed a hybrid model that couples electrochemical model of lithium ion battery (NMC-Graphite as an example) and an equivalent circuit model of lead acid battery in order to study the behavior of 12V dual-battery microhybrid architectures.

Logistic regression analysis for accident cases of NASS-PCDS (National Automotive Sampling System-Pedestrian Crash Data Study) clearly shows that the extent and the degree of pedestrian's lower extremity injury depend on various factors such as the impact speed, the ratio of the pedestrian height to that of the bonnet leading edge (BLE) of the striking vehicle, bumper to knee ratio, bumper lead angle, age of the pedestrian, and posture of the pedestrian at the time of impact. The pedestrian population is divided in 3 groups, equivalent to small-shorter, medium-height and large-taller pedestrian with respect to the “pedestrian to BLE height-ratio” in order to quantify the degree of influence of lower leg injuries in each group. Large adult male finite element model (95th percentile male: 190 cm and 103 kg) was developed by morphing the Japan Automobile Manufacturers Association (JAMA) 50th percentile male.

Selective Catalytic Reduction (SCR) is a leading aftertreatment technology for the removal of nitrogen oxide (NOx) from exhaust gases (DeNOx). It presents an interesting control challenge, especially at high conversion, because both reagents (NOx and ammonia) are toxic, and therefore an excess of either is highly undesirable. Numerous system layouts and control methods have been developed for SCR systems, driven by the need to meet future emission standards. This paper summarizes the current state-of-the-art control methods for the SCR aftertreatment systems, and provides a structured and comprehensive overview of the research on SCR control. The existing control techniques fall into three main categories: traditional SCR control methods, model-based SCR control methods, and advanced SCR control methods. For each category, the basic control technique is defined. Further techniques in the same category are then explained and appreciated for their relative advantages and disadvantages.

This paper describes the development of high efficiency and compact bumper recycling equipment for facilitating bumper recycling globally. Various equipment to remove paint coat from bumper has been developed since 90s', using mechanical, physical or chemical method. However, it is difficult to promote bumper recycling without realizing cost effective overall system from paint coat removal to pelletizing. Our company jointly developed method of mechanically removing paint coat and has committed to bumper recycling in the form of outsourcing since 2000. In 2010, a dedicated plant for recycling bumpers was launched on the premises of our Oppama Assembly Plant in Japan. In the future, promoting bumper recycling at other overseas assembly plants is necessary as vehicle production will expand globally.