Search Results

Friction stir spot welding (FSSW) is applied to join advanced high strength steels (AHSS): galvannealed dual phase 780 MPa steel (DP780GA), transformation induced plasticity 780 MPa steel (TRIP780), and hot-stamped boron steel (HSBS). A low-cost Si₃N₄ ceramic tool was developed and used for making welds in this study instead of polycrystalline cubic boron nitride (PCBN) material used in earlier studies. FSSW has the advantages of solid-state, low-temperature process, and the ability of joining dissimilar grade of steels and thicknesses. Two different tool shoulder geometries, concave with smooth surface and convex with spiral pattern, were used in the study. Welds were made by a 2-step displacement control process with weld time of 4, 6, and 10 seconds. Static tensile lap-shear strength achieved 16.4 kN for DP780GA-HSBS and 13.2 kN for TRIP780-HSBS, above the spot weld strength requirements by AWS. Nugget pull-out was the failure mode of the joint.

An important emerging technical area is computer-based modeling of the various manufacturing processes that are used in many diverse industries. These models are used to optimize manufacturing techniques to reduce fabrication costs and improve the service performance. One manufacturing process important in steel fabrication is welding. It can be a useful tool to aid in reducing fabrication costs and service durability by optimizing the weld process and is the subject of this paper.

This paper presents a numerical analysis of the effect of weld induced residual stress on the fatigue behavior of a T-joint. The thick-section T-joint contained 18 individual weld passes and was subjected to fully-reversed, zero-maximum, and zero-minimum fatigue cycling. The effect of the residual stress was demonstrated by comparing the result with and without residual stress. It was concluded that the local fatigue parameters (mean stress, alternating stress, and stress ratio) at the suspected crack initiation site were changed significantly by the residual stresses when the applied stress were other than fully reversed. In addition, the effect of the stress concentration at the weld was more significant that the effect of the residual stress for the applied fatigue loads levels that were considered. The analysis method presented can be used to assess weldment design and process variables.

Chemical and physical properties of various plastics used for plastic abrasive applications are presented. All testing is done in compliance with MIL-P-85891 (AS), “Plastic Media for Removal of Organic Coatings”. Density and heavy density particle contamination are particularly important tests relative to aerospace applications.

Performance of various plastic abrasive materials is compared in a typical aerospace coatings removal application. Media aggressiveness towards substrates, stripping capabilities, effects of plastic breakdown, and plastic consumption are compared. Lower density plastics are shown to be more substrate protective than higher denisty plastics. Stripping rates are shown to be dependent both on plastic hardness and breakdown resistance of the plastic.

Optimization parameters designed to minimize residual stress and maximize coatings removal rates are presented. Stress saturation curves are presented and compared for the optimized blasting parameters using different plastic abrasive materials.

Currently the U. S. Department of Defense (DoD) exclusively uses potassium acetate (KAc)-based runway deicing fluids (RDFs) to deice and anti-ice military runways and taxiways. Commercial airports predominantly use KAc, but some also use RDFs composed of KAc plus propylene glycol (PG) or urea plus PG. Conventional RDFs have environmental concerns due to toxicity as well as material compatibility problems such as corrosion of aircraft carbon brake-pad components, cadmium-plated landing gear, and airfield lighting fixtures. Under the Strategic Environmental Research and Development Program (SERDP), Battelle tested a series of patented - bio-based RDFs to address these issues. Tests showed that the Battelle RDFs met the mandatory Aerospace Material Specification (AMS) 1435 requirements. These new RDFs have reduced ecotoxicity compared to currently used RDFs and are compliant with all other environmental requirements.

In the new design, the electrode employs composite electrode face construction with dissimilar materials. A cylindrical insert located in the electrode face center is made of low thermal and electrical conductivity material, such as stainless steel, and an annular outer sleeve is made of stainless steel and located at periphery of the electrode. Base material of the electrode is still made of copper alloys. With this electrode design, the electrical-thermal-mechanical conditions can be improved by confining the current flow path to reduce current level required for the weld nugget formation, and optimizing electrode pressure distribution, and minimizing electrode face heating and plastic deformation.

Increased research devoted to the foundry arts has resulted in a greater understanding of the factors essential in producing high quality castings. One outgrowth of these studies has been the development of premium quality aluminum castings. The procedures used for the production of premium quality castings are reviewed, and the improvements in properties that result from adequate attention to these procedures are described.

Application of electron microscopy to the study of fractures and fracture mechanisms is reviewed. Static fractures and the fracture of multiphased alloys have been studied, and significant information obtained. Striations on the fracture surface are associated with fatigue crack propagation and are directly related to crack growth rates. Various factors such as strength level, corrosive media, and second-phase particles are known to influence the appearance of the striations under the electron microscope. Since the appearance under the microscope of each type of fracture is quite unique, electron microscopic fractography is also an aid in service failure analyses.

Experimental research on an integrated Bosch reactor and water-vapor electrolysis unit for oxygen recovery from carbon dioxide is described. A principal feature of the integration is the use of regenerable solid absorbent for periodic water-vapor transfer in a gravity-independent manner to avoid gas-liquid separation problems. The carbon dioxide reduction subsystem was based on batch-wise operation of two Bosch reactors to permit periodic shutdown for carbon removal. Experimental results are presented on operation of the Bosch reactor which include catalyst activation, recycle rate, recycle gas composition, reactor temperature, catalyst consumption, packing density of carbon and life of reactor materials during extended operation. Experimental data are presented on the solid-absorbent unit with silica gel and synthetic zeolites for removal of water vapor from the Bosch reaction and for water-vapor feed to an electrolysis unit.

THIS PAPER describes an investigation into the use of radioactive cylinders in wear research. Battelle Institute and Fairbanks, Morse agree that the method has potential as a research tool. The effect on cylinder wear experienced with variables such as starting, idle or cold temperature operation, sudden load changes, speed, torque, and such, can be determined easily and relatively inexpensively. The authors describe the techniques and precautions taken during the testing. *

The cost of electroplating zinc die castings can be reduced by employing microcracked or microporous chromium in place of conventional chromium; the former is more effective in improving corrosion performance while conserving nickel. Exposure data are examined and specifications for nickel and chromium content are presented.

After several alternative procedures were investigated for preparing chromium-plated zinc die castings for painting, one procedure proved best for contaminated chromium surfaces. This procedure included six steps: (1) alkaline spray cleaning, (2) electrolytic alkaline cleaning, (3) rinsing with high-purity water with a specific resistance of 500,000-700,000 ohm-cm, (4) immersing in chromic acid solution (0.05 oz/gal) at 150 F for 2 minutes, or treating cathodically in 0.7 oz/gal of sodium dichromate with a current density of 0.05 amp/sq ft for 30-60 sec, (5) rinsing with high-purity water, (6) forced-air drying with filtered air at 15 psi. Good adherence was obtained by following these procedures and painting with a single coat of acrylic or alkyd-resin paint. Other preparation procedures resulted in inferior paint adherence.

THIS report of a survey of hydraulic packings, especially O-ring seals, covers friction studies, torsional strength tests, plasticizer development, a study of rubbers, molding technique, and spiral failure. The Institute is reported to be planning to conduct research work along the lines of cycling tests and studies of stress aging, compounding, and backup rings.

An axisymmetric finite element model is generated to simulate the windshield glass damage propagation subjected to impact loading of a flying object. The windshield glass consists of two glass outer layers laminated by a thin poly-vinyl butyral (PVB) layer. The constitutive behavior of the glass layers is simulated using brittle damage mechanics model with linear damage evolution. The PVB layer is modeled with linear viscoelastic solid. The model is used to predict and examine through-thickness damage evolution patterns on different glass surfaces and cracking patterns for different windshield designs such as variations in thickness and curvatures.

This paper addresses the modeling issues of resistance spot welds. The state of the art modeling techniques on weld process simulation, weld property prediction and weld engineering performance evaluation are presented. First, weld process simulation is performed using the incrementally coupled thermal-electrical-mechanical analyses. The resulted weld nugget size, weld residual stress and weld material property distributions are then used in determining the static performance of a single weld coupon. Comparisons with experimental measurements are presented as validations. Results generated from this single weld coupon is then used in the simulation of dynamic crush mechanism of a spot welded single hat section.