Search Results

The efforts of the ISO “Test Variability Task Force” have been aimed at improving the understanding and at reducing brake dynamometer test variability during performance testing. In addition, dynamometer test results have been compared and correlated to vehicle testing. Even though there is already a vast amount of anecdotal evidence confirming the fact that different procedures generate different friction coefficients on the same brake corner, the availability of supporting data to the industry has been elusive up to this point. To overcome this issue, this paper focuses on assessing friction levels, friction coefficient sensitivity, and repeatability under ECE, GB, ISO, JASO, and SAE laboratory friction evaluation tests.

In order to satisfy environmental regulations while maintaining strong performance and excellent fuel economy, advanced diesel engines are employing sophisticated air breathing systems. These include high pressure and low pressure EGR (Hybrid EGR), intake and exhaust throttling, and variable turbine geometry systems. In order to optimize the performance of these sub-systems, system level controls are necessary. This paper presents the design, benefits and test results of a model-based air system controller applied to an automotive diesel engine.

This paper proposes and evaluates improvements to a crash simulation of a fuel delivery module in a fuel tank. The simulations were performed in ANSYS/LS-DYNA. Deviations between the original simulation and test data were studied and reasons for the deviations hypothesized. These reasons stemmed from some of the simplifying assumptions of the model. Improvements consisted of incorporating plasticity and strain rate effects into the material models. Performance criteria were also directly incorporated into the material models such that non-performing portions of the model could be deactivated during the simulation. Finally, solid-fluid interactions were added into the simulation to include the momentum transfer from fuel to the fuel delivery module. It was previously thought that effects of a crash would be most severe on the module when the fuel tank was empty and the module was full with fuel.

Networking of active and passive safety is the fundamental basis for comprehensive vehicle safety. Situation-relevant information relating to driver reactions, vehicle behavior and traffic environment are fed into a crash probability calculator, which continually assesses the current crash risk and intervenes when necessary with appropriate measures to avoid a crash and reduce potential injuries. This provides effective protection not only for vehicle occupants but also for other, vulnerable road users. As this functionality up till now only relates to the vehicle itself, the next logical step is enhancement leading to the ultimate goal in safety performance, telematics. The integration of this embedded, in-vehicle wireless communication system allows Car-to-Car (C2C) and Car-to-Infrastructure (C2I) functionality for, e.g. hazard warning. This is an integral element of the cascaded ContiGuard® protection measures.

The AUTomotive Open System ARchitecture (AUTOSAR) Development Partnership has published early 2008 the specifications Release 3.0 [1], with a prime focus on the overall architecture, basic software, run time environment, communication stacks and methodology. Heavy developments have taken place in the OEM and supplier community to deliver AUTOSAR loaded cars on the streets starting 2008 [2]. The 2008 achievements have been: Improving the specifications in order to secure the exploitation for body, chassis and powertrain applications Adding major features: safety related functionalities, OBD II and Telematics application interfaces.

In the research project between the Institute of Automotive Engineering (FZD) of the Technische Universität Darmstadt (TUD) and Continental Teves AG & Co. oHG a new modeling concept has been developed. With the aim to enhance the current development process, the brake caliper is modeled based on coupled rigid bodies integrated into a nonlinear system model. Using an explicit interface definition, the number of degrees of freedom is minimized and the calculation of caliper performance is possible over a wide range of parameters. Compared to models based on the Finite Element Method (FEM), fully parameterized geometry from CAD is not necessary, thus the caliper can be optimized for a variation of its geometrical and physical parameters. With this modeling approach, typical performance criteria such as caliper fluid displacement, hysteresis, uneven pad wear and residual torque can be calculated in a virtual bench test.

The US American government introduced a law to mandatorily equip passenger vehicles with rear view cameras. Furthermore, US NCAP presented a test for passenger vehicles to brake on pedestrians while back up. These two circumstances lead to main motivation of the development of the Comfort Backup Assist (CBUA). Nevertheless, more and more passenger cars in general are being equipped with rear view cameras. Rear view system (RVS) allows to deliver a rear-view camera system including a braking functionality which is intended to make the driving mission safer and reduce the number of accidents in parking driving situations. RVS also focus on vehicle safety by reducing accidents while taking reversing/parking scenarios and to provides slow de-acceleration of the vehicle gradually to avoid jerk and increase the ride comfort.

Driver assistance features have been introduced to the market focusing on basic, independent functional scenarios. The trend is showing that these kinds of products are facing more and more complex scenarios and we are transitioning from single independent functions to a strongly networked system. Some of the drivers for future autonomous vehicles are 360° monitoring by active safety technology and V2X (vehicle to vehicle or vehicle to infrastructure) communication. In the past vehicles were strictly operated by the driver. Advanced driver assistance products added so called feedback features like lane departure warning, forward collision warning, and blind spot monitoring. First steps towards semi-autonomous driving started with the development of active support functions like adaptive cruise control or lane keeping support. Collision mitigation with various authority levels is the next milestone towards automation followed by other, even more advanced, features.

Compressed natural gas (CNG) is an attractive, alternative fuel for spark-ignited (SI), internal combustion (IC) engines due to its high octane rating, and low energy-specific CO2 emissions compared with gasoline. Directly-injected (DI) CNG in SI engines has the potential to dramatically decrease vehicles’ carbon emissions; however, optimization of DI CNG fueling systems requires a thorough understanding of the behavior of CNG jets in an engine environment. This paper therefore presents an experimental and modeling study of DI gaseous jets, using methane as a surrogate for CNG. Experiments are conducted in a non-reacting, constant volume chamber (CVC) using prototype injector hardware at conditions relevant to modern DI engines. The schlieren imaging technique is employed to investigate how the extent of methane jets is impacted by changing thermodynamic conditions in the fuel rail and chamber.

Accuracy of clutch torque model which converts target torque to target stroke is essential to control the dry clutch system. Continuous Adaptation algorithm requires micro slip control during in-gear driving. Clutch judder during micro slip control can cause detrimental effect on the output of controller as slip speed is calculated by deviation of engine speed and clutch speed. Conventional approach to avoid clutch judder is using low pass filter to the input of controller which is slip speed. But this affect to the overall response time of slip controller. In this paper, signal processing algorithm is design and tested for the clutch speed(Input shaft speed). With low pass filter in clutch speed, clutch judder signal is decreased but overall time delay creates static error during acceleration. Several phase advance algorithm is designed to overcome the static error during acceleration without disadvantage of decreasing clutch judder signal.

Global automotive fuel economy and emissions pressures mean that 48 V hybridisation will become a significant presence in the passenger car market. The complexity of powertrain solutions is increasing in order to further improve fuel economy for hybrid vehicles and maintain robust emissions performance. However, this results in complex interactions between technologies which are difficult to identify through traditional development approaches, resulting in sub-optimal solutions for either vehicle attributes or cost. The results presented in this paper are from a simulation programme focussed on the optimisation of various advanced powertrain technologies on 48 V hybrid vehicle platforms. The technologies assessed include an electrically heated catalyst, an insulated turbocharger, an electric water pump and a thermal management module.

The “Car of the Future” project converted a production 2015 rear-wheel-drive (RWD) Subaru BRZ into a series hybrid electric vehicle (HEV) with an intermediate milestone of a battery electric vehicle (BEV). This intermediate BEV step provided a point at which the vehicle could be evaluated in its all-electric operation with the absence of what were once critical components, including its original powertrain and powertrain electronics. This paper selects an appropriate electric machine that will meet the desired requirements for the “Car of the Future” BEV milestone. Vehicle technical specifications (VTS), which define critical vehicle requirements, were provided by the sponsor and adjusted to align with common requirement criteria such as acceleration and gradeability.

Propulsion system control algorithms covering the functional needs of xEV propulsion (‘x’ donates P0-P4 configurations) systems are presented in this paper. The scope and foundation are based on generic well-established HEV controller architectures. However, unlike conventional HEV (series, parallel and power split) powertrains, the next generation of integrated electric propulsion configurations will utilize a single micro controller that supports multiple control functions ranging from the electric machines, inverters, actuators, clutch solenoids, coolant pumps, etc. This presents a unique challenge to architect control algorithms within the AUTOSAR framework while satisfying the complex timing requirements of motor/generator-inverter (MGi) control and increased interface definitions between software components to realize functional integration between the higher level propulsion system and its sub-systems.

Reductions of hardware costs as well as implementations of new innovative functions are the main drivers of today's automotive electronics. Indeed more and more resources are spent on adapting existing solutions to different environments. At the same time, due to the increasing number of networked components, a level of complexity has been reached which is difficult to handle using traditional development processes. The automotive industry addresses this problem through a paradigm shift from a hardware-, component-driven to a requirement- and function-driven development process, and a stringent standardization of infrastructure elements. One central standardization initiative is the AUTomotive Open System ARchitecture (AUTOSAR). AUTOSAR was founded in 2003 by major OEMs and Tier1 suppliers and now includes a large number of automotive, electronics, semiconductor, hard- and software companies.

In recent years, electrification of vehicle powertrains has become more mainstream to meet regulatory fuel economy and emissions requirements. Amongst the many challenges involved with powertrain electrification, developing supervisory controls and energy management of hybrid electric vehicle powertrains involves significant challenges due to multiple power sources involved. Optimizing energy management for a hybrid electric vehicle largely involves two sets of tasks: component level or low-level control task and supervisory level or high-level control task. In addition to complexity within powertrain controls, advanced driver assistance systems and the associated chassis controls are also continuing to become more complex. However, opportunities exist to optimize energy management when a cohesive interaction between chassis and powertrain controls can be realized.

The introduction of new light-duty vehicle emission limits to comply under real driving conditions (RDE) is pushing the diesel engine manufacturers to identify and improve the technologies and strategies for further emission reduction. The latest technology advancements on the after-treatment systems have permitted to achieve very low emission conformity factors over the RDE, and therefore, the biggest challenge of the diesel engine development is maintaining its competitiveness in the trade-off “CO2-system cost” in comparison to other propulsion systems. In this regard, diesel engines can continue to play an important role, in the short-medium term, to enable cost-effective compliance of CO2-fleet emission targets, either in conventional or hybrid propulsion systems configuration. This is especially true for large-size cars, SUVs and light commercial vehicles.

Dihydrogen, as a zero CO2 fuel, is a strong candidate for internal combustion engine to limit global warming. This study shows the impact of standard tuning parameters on mixture homogeneity and combustion characteristics. A 2.2L Diesel engine on which the head was reworked to allow side mounted direct injector and central mounted spark plug was selected. The discussed tests were made at low engine speed and partial load. A spark advance sweep at different air-fuel ratios (λ) was conducted. The exponential relation between λ and NOx emissions is highly marked and extremely low NOx emissions up to 1.7 g/kWh at minimum spark advance for maximum brake torque can be measured. A λ sweep was performed at different starts of injection (SOI). The results show that, depending on the engine speed, a later SOI might lead to lower NOx emissions. For a λ setpoint of 1.8, at 1500 rpm, late SOI leads to 30% higher NOx emissions where at 2500 rpm these emissions are 26% lower.

The global automotive industry is undergoing a significant transition as battery electric vehicles enter the market and diesel sales decline. It is widely recognized that internal combustion engines (ICE) are needed for transport for years to come, however, demands on fuel efficiency, emissions, cost, and performance are extremely challenging. Gasoline compression ignition (GCI) is one approach to achieving demanding future efficiency and emissions targets. A key technology enabler for GCI is partially premixed, compression ignition (PPCI) combustion, which involves two high-pressure, late, fuel injections during the compression stroke. Both NOx and smoke emissions are greatly reduced relative to diesel engines, and this reduces aftertreatment (AT) requirements significantly. Exhaust rebreathing (RB) is used for robust low-load and cold operation. This is enabled by use of 2-Step, mode switching rocker arms to allow switching between rebreathe and normal combustion modes.

Since several decades, passenger cars and light duty vehicles (LDV) with spark-ignited engines reach full pollutant conversion during warm up conditions; the major challenge has been represented by the cold start and warming up strategies. The focus on technology developments of exhaust after treatment systems have been done in the thermal management in order to reach the warm up conditions as soon as possible. A new challenge is now represented by the Real Driving Emission (RDE) Regulation as this bring more various, and not any longer cycle defined, cold start conditions. On the other hand, once the full conversion has been reached, it would be beneficial for many Exhaust After Treatment System (EATS) components, e.g. for overall durability if the exhaust gas temperature could be lowered. To take significant further emission steps, approaching e.g. zero emission concepts, we investigate the use of Electrical Heating Catalyst (EHC) also including pre-heating.

Riveting is a process used to fasten printed circuit board to housing that offers several advantages compared to screws. This involves a cylindrical pin that protrudes from the housing being compressed with a concave tool to produce a rivet head that fills the PCB hole and holds it in place over service life of the component. The process as performed currently in-house uses parameters that have not been optimized. Testing has revealed that the process is subjecting the PCB to surface strains higher than 1000μɛ which is the limit as recommended by standards. Exceeding this limit reduces the reliability of electrical components and increases risk of field failures. This risk can be mitigated by improving the riveting process parameters to prevent high strain from reaching components. Having a finite element model for high deformation problems is an essential prerequisite to explore riveting process improvement.