Search Results

Gear fault diagnosis is important in the vibration monitoring of any rotating machine. When a localized fault occurs in gears, the vibration signals always display non-stationary behavior. In early stage of gear failure, the gear mesh frequency (GMF) contains very little energy and is often overwhelmed by noise and higher-level macro-structural vibrations. An effective signal processing method would be necessary to remove such corrupting noise and interference. This paper presents the value of optimal wavelet function for early detection of faulty gear. The Envelope Detection (ED) and the Energy Operator are used for gear fault diagnosis as common techniques with and without the proposed optimal wavelet to verify the effectiveness of the optimal wavelet function. Kurtosis values are determined for the previous techniques as an indicator parameter for the ability of early gear fault detection. The comparative study is applied to real vibration signals.

Vehicle Handling performance depends on many parameters. One of the most important parameters is the dynamic behavior of the steering system. However, steering system had been enhanced thoroughly over the past decade where Active Front Steering (AFS) is now present and other system as Active Independent Front Steering (AIFS) is currently in the research phase. Actually, AFS system adopt the front wheels’ angles base on the actual input steering angle from the driver according to vehicle handling dynamics performance. While, the AIFS controls the angle of each front wheel individually to avoid reaching the saturation limits of any of the front wheels’ adhesion. In this paper modeling and analysis of an AIFS is presented with Tire Work Load (TWL) based controller. Magic Formula tire model is implemented to represent the tire in lateral slip condition.

In this paper, a nonlinear semi-active vehicle suspension system using MR fluid dampers is investigated to enhance ride comfort and vehicle stability. Fuzzy logic and fuzzy self-tuning PID control techniques are applied as system controllers to compute desired front and rear damping forces in conjunction with a Signum function method damper controller to assess force track-ability of system controllers. The suggested fuzzy self-tuning PID operates fuzzy system as a PID gains tuner to mitigate the vehicle vibration levels and achieve excellent performance related to ride comfort and vehicle stability. The equations of motion of four-degrees-of-freedom semi-active half-vehicle suspension system incorporating MR dampers are derived and simulated using Matlab/Simulink software.

The dynamics of vehicles became one of the most important aspects for current developments of electronically controlled steering, suspension and traction/braking systems. However, most of the published research on vehicle maneuverability doesn't take into account the effect of the dynamic tire load and its variation on uneven roads. Clearly, it was stated that using a suitable active suspension system could reduce this dynamic tire load. This dynamic tire load is playing a vital role as it is the major link between the vertical and lateral forces exerted on the road, which affects the lateral dynamics of the vehicle. In this paper, a practical hydro-pneumatic limited bandwidth active suspension system with and without wheelbase preview control is used to study its influence on the vehicle stability in lateral direction. The model is a longitudinal half car with four degrees of freedom.

The bearing capacity of soils stands as one of the most important parameters that determine the vehicles’ off-road mobility. Soil bearing capacity can be determined either experimentally or by calculation using analytical and or empirical formulas. One of the most famous formulas is the Bekker's. Recently, Artificial Neural Networks (ANNs) technique became a powerful tool that can be used for predicting systems’ behavior and performance. The main objective of this paper is to predict the bearing capacity of the soil (plate-sinkage relationships) by using Artificial Neural Networks and to compare the actual results of soil bearing capacity (collected data from Ph.D. Thesis) with results obtained from neural network model and Bekker's formula. The comparison showed clear superiority and accuracy of neural network technique. Another objective is to check the generalization ability of the neural network model in predicting the plate-sinkage relationships by using the hypothetical plate.

In the design of recreational vehicle alternators, a particular challenge arises from marketing and engineering teams' desire to ensure that their products meet “best in class” sound quality characteristics. Furthermore, it is desirable to know these characteristics in measurable engineering terms in the product design stage, preferably before prototypes are built and tested. However, the aim of this paper is to investigate experimentally the electromagnetic sound quality characteristics of a vehicle alternator with the view of determination. For this reason, a special test rig was designed to simulate the alternator electromagnetic noise source. The results indicate that significant information can be obtained for this source. This can be an effective way to control this generated noise and consequently improve the vehicle alternator sound quality and look promising.

The number of speed humps (sleeping policemen) has seen a global increase in the last decade. This paper addresses the geometric requirements of these humps using Genetic Algorithms optimization techniques to control the speed, stability, and ride feel of the traversing vehicles. The interaction between road hump profile and the modeled vehicles (passenger and a two-axle truck) are studied with a dynamic model. The shape of the proposed profile is described by numbers of amplitudes of harmonic functions. The extreme acceleration of the drivers’ seats of the vehicles traversing the hump is set as multiobjective function for the optimization process, taking into consideration the road-holding ability represented by the tire lift-off speed. The results show that hump geometry can be improved while fulfilling the requirements of speed control and vehicle dynamic responses.

The DC power supply is ingredient part in the automotive industries as it has been used as a DC power supplies for a wide range of loads. Meanwhile, it is mandatory for battery charging. These types however, causes many problems such as poor power factor, high input current harmonics distortion and uncontrolled DC voltage. In this paper, an improved input power factor correction that uses a combined control system consists of two nested loops with a feedback of the DC voltage and input current as long as a feed forward from the output power. The system has been analyzed, modeled, simulated and experimentally verified. The novel feature of the proposed control scheme resides in fact that it is not only achieve nearly unity power factor with minimum input current total harmonics distortion only but it also introduce superior performance in DC voltage transient conditions.

Squeal from brakes is a problem in the automotive industry and large efforts are made to understand the squeal tendencies. The approach taken is mainly to change the design of the caliper, fine-tune the brake pad material and finally to trim the introducing shims on the backside of the pads. Despite these efforts still no general solutions exist. To advance the situation, a deeper understanding of the actual source of excitation of the sound in the friction interface is needed. However, in the present investigation the surfaces modifications of brake disc and pad have been tested with respect to the understanding properties. The surfaces modifications are slotted pad material and coated disc. All tests have been made in a brake test stand consisting of a complete front wheel corner of a vehicle. The changes have resulted in a significant understand of the generated noise.

Recently, the control of traffic flow has been proposed using several types of criteria (e.g. minimum-time control, minimum fuel control and so on). Most recently, an environmental noise pollution problem caused by the road traffic is being aggravated more and more by the consolidation and expansion of roadway system particularly in urban areas. However, the objective of this paper is to control road traffic flow by regulating traffic noise propagation in an urban area in Cairo city. The results of traffic noise prediction obtained by trending of the experimental data collecting by systematic noise measurement and the evaluation of the traffic noise which is in close connection with physical parameters of traffic flow and noise propagation characteristics is presented. The analysis of road traffic flow noise control is based on the mixed integer non-linear programming technique, where the optimal control strategy is used.

In this paper, a hybrid roll control system, including passive and active roll control units, is designed to improve the roll dynamics of tanker vehicles and to reduce the lateral shifts of the liquid cargo due to lateral accelerations. The passive control system consists of radial partitions installed inside the vehicle container. These partitions rotate in phase with the liquid cargo as one unit about the longitudinal axis of the container in response to the induced momentum forces due to the lateral acceleration excitation. Torsion dampers are fixed between the partitions and the container's front and rear walls to reduce the oscillating motion of the liquid cargo. While the passive partition dampers control the dynamics of the liquid cargo inside the container, the dampers of the vehicle suspension are switchable, generating anti-roll damping moments based on the lateral acceleration level and the container filling ratio.

In this paper, a direct technique to estimate the rollover threshold limits of partially filled tank trucks is applied for banked roadways. Overturning and restoring moments are calculated as functions of tank shape, fill level, gradient of both liquid cargo free surface and the lateral inclination of banked road surfaces. The static rollover threshold of tanker trucks traveling on laterally banked roadways is estimated by balancing the net value of the total overturning moment against the net value of the restoring moment. Different filling ratios are considered for circular, elliptical and modified tank vehicles. The rollover threshold limits are calculated considering a superelevation range of (0.0-0.1) for the lateral road banking as defined by Blue and Kulakowski (1991). It is shown that the vehicle rollover threshold limit increases with an increase of the angle of the lateral road banking.

This paper is concerned with the analysis of the performance of actively suspended vehicles when the effects of the aerodynamics are considered. The investigation is wholly theoretical and treats a half vehicle model, active suspension, through simulation of running at different speeds on a random-profile road. Using classical control laws, which do not account for aerodynamic effects, it is shown that starting from a vehicle speed of 35 m/s, ride comfort and road holding parameters significantly deteriorate. A method is introduced to modify the control strategy so that these effects can be taken into consideration. Various forms of control laws are presented, and conclusions are drawn to specify the benefits that could be achieved from this modified control strategy.

In this paper, the Kalman filter algorithm is used to design a practical adaptive control strategy. The adaptation is intended to adjust the system operation according to the changes of road input. A moderate adaptive time of at least 3 seconds is used. Limit stops are added to prevent the increase in the wheel travel behind the specified limit. The active suspension feedback system is designed based on measuring only the suspension displacement. A gain scheduling adaptive scheme which consists of four sets of state feedback gains is designed. The estimation process of dynamic tyre deflection and other necessary state variables through the Kalman filter is illustrated. Among other things, this estimate is used to derive the gain scheduling adaptive scheme. The strategy is applied to a quarter car active suspension system. Results are generated at a constant speed on random road profiles.

The main objective of this research is to find a general empirical formula to predict vehicle frontal area applied to most types of vehicles. This was done on 21 vehicles; passenger cars, buses and trucks by calculating their frontal area by using image processing technique on cars photos extracted from catalogues. The software (Data Fit) is used to establish the required empirical formula. The results showed that the empirical formula is simple and accurate enough for finding out the vehicles frontal areas.

A full vehicle of a preview control semi-active suspension system based on an interval type-2 fuzzy controller design using a magnetorheological (MR) damper to improve ride comfort is investigated in this paper. It is integrated with the force distribution system to obtain the optimal rate of road adhesion during braking and handling. The nonlinear suspension model is derived by considering vertical, pitch, and roll motions. The preview interval type-2 fuzzy technique is designed as a system controller, and it is attached with a Signum function method as a damper controller to turn on the voltage for the MR damper. This voltage is adjusted for each wheel based on the external excitation generated by road roughness in order to enhance ride comfort. To describe the effectiveness and adaptable responses of the preview controlled semi-active system, the performance is compared with both the passive and MR passive suspension systems during time and frequency domains.

The previous research work on Active Independent Front Steering (AIFS) system concluded an enhanced vehicle response and tire adhesion utilization. Some research emphasizes the importance of Tire Work load (TWL) in the generation of maximum possible tire forces that ensures vehicle controllability and stability. In this study, a mathematical model is constructed to investigate the effect of TWL as a parameter on AIFS performance. Toward such a target, a new Fuzzy control strategy is developed based on TWL and vehicle yaw rate as control inputs for the AIFS controller. Unfortunately, the TWL is not a measurable parameter or even easy to be estimated. Consequently, another control strategy was implemented based on slip angle and vehicle yaw rate as inputs for the AIFS controller.

Adaptive neuro-fuzzy inference system (ANFIS) technique has been developed and applied by numerous researchers as a very useful predictor for nonlinear systems. In this paper, non-parametric models have been investigated to predict the direct and inverse nonlinear dynamic behavior of magnetorheological (MR) fluid dampers using ANFIS technique to demonstrate more accurate and efficient models. The direct ANFIS model can be used to predict the damping force of the MR fluid damper and the inverse dynamic ANFIS model can be used to offer a suitable command voltage applied to the damper coil. The architectures and the learning details of the direct and inverse ANFIS models for MR fluid dampers are introduced and simulation results are discussed. The suggested ANFIS models are used to predict the damping force of the MR fluid damper accurately and precisely. Moreover, validation results for the ANFIS models are proposed and used to evaluate their performance.

The anti-lock brake system (ABS) is a vital system in modern vehicles that prevents automotive wheels from locking during an emergency brake. This paper aims to introduce an efficient, optimized proportional integral derivative (PID) controller tuned using a genetic algorithm (GA) to enhance the performance of ABS. The PID control method is a very famous control algorithm employed in numerous engineering applications. The GA is used to solve the nonlinear optimization problem and search for the optimum PID controller gains by identifying the solution to the problem. A mathematical model of ABS is derived and simulated using Matlab and Simulink software. The proposed optimized PID-controlled ABS is compared to the conventional ABS controlled using a Bang-Bang controller. System performance criteria are evaluated and assessed under different road adhesion coefficient values to judge the success of the proposed PID controller tuned using GA.

In this paper, a fuzzy-PID controller is applied in a half vehicle active suspension system to enhance vibration levels of vehicle chassis and passenger seat. The fuzzy-PID controller consists of fuzzy and PID connecting in a series manner, the fuzzy output is considered as the PID input. Genetic Algorithm (GA) is selected to tune controller parameters to obtain optimal values that minimize the objective function. The equations of motion of five-degrees-of-freedom active half-vehicle suspension system are derived and simulated using Matlab/Simulink software. Double bumps and random road excitations are used to study the performance of suspension systems including bounce and pitch motion. The performance of the active suspension system using optimized fuzzy-PID controller is compared with conventional passive to show the efficiency of the proposed active suspension system.