Search Results

In order to meet increasing demands for safety and comfort in a vehicle compartment, automatic adjustment of seat, mirrors, steering wheel has been developed. The multiplex wiring system was constructed for the automatic adjustment of the cockpit elements to drivers preferred positions or to physique-matched settings based on ergonomic data. This paper describes the construction of the multiplex system and functions of automatic adjustment of the cockpit elements for comfortable driving position and better visibility.

During next decade, automotive engineers will take up unprecedented challenges to meet a variety of technical demands on passenger cars. While performance, refinement and reliability will continue to be major technical goals of passenger cars, reducing their impact on the environment not only in urban areas but also on the global basis will become an increasingly urgent issue. In addition, the need for energy and resources saving will necessitate development of more fuel efficient cars, exploitation of alternative energy and recycled materials. In this paper, the authors will review various alternative engines as candidates to satisfy the above demands. The authors will also discuss various alternative transportation energy sources such as alcoholic fuels, natural gas, hydrogen and electricity. Finally the trends of future passenger car engine design will be discussed.

Three zone mixture preparation model, assuming that fuel and air are distributed in three separate zones, fuel air and mixture zone, was proposed. Air Utilization Efficiency derived from the model was used to evaluate the mixing nonuniformity. Effect of the large scale nonisotropic turbulence downstream of the dimple or edge in the intake port of MPI engine on the convective mass transfer from fuel film was clarified by the proposed nondimensional index, Local Sherwood Number. It was found that when the fuel is injected toward the wall where large scale turbulence exists, almost all of the fuel is seeded in the air passing the region at the beginning of the intake process, resulting in the time-resolved nonuniformity of the mixture strength at the intake valve. Using the Air Utilization Efficiency, it was elucidated that time-resolved mixing nonuniformity at intake valves induces spatially nonuniform fuel/air distribution in the cylinder.

This paper describes a control strategy for autonomous vehicles in an intelligent vehicle/highway system. The control concept aims at the compatibility of passenger riding comfort and vehicle controllability. The main subject of this paper is lateral control of vehicles. In order to analyze riding comfort, we have experimented on the lateral riding comfort during a lane change. It was found that the riding comfort is mainly related to the jerk more than the acceleration, and that the trajectory pattern is important. According to the experimental results, a motion control system was designed. We found through the computer simulation and the experiment with an autonomous test vehicle that comfortable ride is realized along with system stability. Lastly, in order to apply this strategy to the longitudinal direction, we have experimented on the longitudinal acceleration with the test vehicle. The results shows that the same strategy is applicable to the longitudinal direction.

New numerical simulation system and experimental evaluation system has been developed to predict and evaluate occupant's thermal sensation in a passenger compartment in which environment is not steady and not uniform. Transitional effective temperature, which is new index of thermal sensation, is proposed and verified to correspond with subjects' thermal sensation votes. The simulation system has two advantage beside the prediction of thermal sensation; automatic generation of a computational model and coupling analysis of temperature including an analysis of temperature distribution inside a cabin, refrigerating cycle, solar radiation, and so on. It was verified that this system well predicts occupant's thermal sensation in a short time.

In the heavy-duty commercial vehicle market in Japan, particularly in the segment of dump trucks and tractors, naturally aspirated engines maintain a dominant market share because of their superior torque characteristics in the low speed range. In order to meet the ever increasing needs for higher speeds of transportation, better fuel economy and higher reliability, and the needs for increasingly strict exhaust emission regulations, Mitsubishi Motors Corporation (MMC) has developed the 8M20, a 20 liter V8 diesel engine. The '92 model series of “THE GREAT”, MMC's main heavy-duty trucks, has featured this new and powerful engine and has been in the market place since October, 1991. The 8M20 is a naturally aspirated engine that provides an output of 294kW/2200rpm, complying with the current Japanese exhaust emission regulations.

A new prototype oxygen storage componented oxygen sensor has been developed which shows significant emission reductions of a 3-way catalyst system. This sensor is composed of ceria, as an oxygen storage component and supported pellets as a buffer layer surrounding the protective coating of the sensor element. This sensor offers a more rapid response than conventional ones under lean and rich fuel mixture excursions, which is caused by CO or O2 electrode poisoning.

This paper concerns driver's burden for visual information processing in which his central vision is coupled with his peripheral one. A visual driving simulator was applied to the first step of the study, where driver's responses to both central and peripheral tasks were simultaneously investigated. The series of test indicate that the driver's responsiveness to the central and peripheral tasks could define the whole burden for visual information processing. Therefore, it appears that the responsiveness to the peripheral vision could be more or less compromised to support the central one.

It has been over a half century since automatic transmission vehicles were introduced to the market, and many improvements in terms of reliability, performance, and cost have since been made. As a result, over 70 percent of passenger cars in the Japanese market today are equipped with automatic transmissions. Despite these advances, customer demand for quieter operation and reduced vibration in automatic transmission vehicles requires further improvements, particularly in the area of reduced shock and smooth response during shifting. Technological improvements have been in progress to solve this problem by such means as reducing engine output during shifting, adapting feedback control and learning shift control. Consequently, an advanced evaluation method for shift quality, with accuracy matching that of human feeling, is required to help improving the shift quality of automatic transmissions.

This paper describes the results of the study and research on ovate wire helical springs which have been jointly conducted by the members of the Japan Society for Spring Research consisting of the engineers from material suppliers, wire and spring producers and automotive manufacturers as well as researchers at Japanese universities. Attention is focused particularly on two types of wire cross sections, typical elliptical shape and Fuchs' egg-shape. Stresses on these two cross sections were analyzed by numerical calculations within the range of practical specification, and then the results have been compared with those of round wire spring. As a result, it has been found that the elliptical wire spring is superior to Fuchs- egg-shaped one for general application. Simple designing methods for the both types of wire helical springs have been developed based on the findings from the stress analysis.

This paper describes an experimental analysis of frictional heat generated between the pads and rotors of disc brakes, to determine the paths and amounts of heat flow. The brakes were applied repeatedly at a constant initial speed, deceleration and interval until brake temperature became saturated. Under these conditions we measured an unsteady temperature distribution state during a single application of the brakes, and also a saturated (quasi-stationary) temperature distribution during repeated braking. Heat flow was studied in six paths: heat conduction to the pad; heat convection to the air from the friction areas of the inner and outer disc, from the ventilating parts and from the tube section of the rotor; and heat conduction to the rotor flange section.

Objective measures to evaluate sound quality are important for proper sound design and noise improvement. In this paper, the objective measures of interior noise of passenger vehicle, which is operated at constant engine revolution speed, are discussed. Subjective evaluation test of the interior noise was done using the semantic differential method. By applying factor analysts to the subjective evaluation scores, three important factors of the sound quality were extracted, i.e. comfortable, powerful and booming factors. Each factor was correlated with various physical values, for example octave band levels. Furthermore, the data is analyzed by multiple linear regression analysis with stepwise variable selection, of the each factor scores against the various physical values. Finally, an objective measure to evaluate each of these factors was conducted using the combination of simple physical values. Each of these measures was good correlation with each of the subjective evaluations.

One of the leading causes of traffic accidents is the reduction of driver's arousal level. Only a driver with an appropriate arousal level can drive an automobile properly. The purpose of this research is to find the possibility of quantifying the reduction of this arousal level. Two methods are used to quantify the reduction in arousal level: one is related to the driver's behavior, and the other is related to his physiological status. The characteristics of controlling the steering wheel are used as indicators of the driver's behavior, which represents the status of information processing in the brain. The variation of heart rate is used as an indicator of physiological status, which could directly represent arousal level related to drowsiness. Eight male and two female drivers participate both in on-the-road tests for the characteristics of controlling the steering wheel and in a test with a driving simulator for the heart rate variation.

Aerodynamic drag reduction is one of the most important aspects of enhancing overall vehicle performance. Many car manufacturers have been working to establish drag reduction techniques. This paper describes the development process of a new small speciality car which achieved coefficient of drag(CD) of 0.25. A description of the test facilities and the systems used for developing the aerodynamic aspect of the car are also introduced briefly.

Flow and flame structure visualization and modeling were performed to clarify the characteristics of bulk flow, turbulence and mixing in a four-valve engine to adopt the lean combustion concept named “Barrel-Stratification” to the larger displacement center-spark four-valve engine. It was found that the partitions provided in the intake port and the tumble-control piston with a curved-top configuration were effective to enhance the lean combustion of such an engine. By these methods, the fuel distribution in the intake port and the in-cylinder bulk flow structure are optimized, so that the relatively rich mixture zone is arranged around the spark plug. The tumble-control piston also contributes to optimize the flow field structure after the distortion of tumble and to enable stable lean combustion.

Three Japanese automobile manufacturers-Mitsubishi Motors Corp., Nissan Motor Co., Ltd., and Toyo Kogyo Co., Ltd.-have been making efforts over the past three years to design and develop effective thermal reactor-exhaust gas recirculation and catalytic converter systems suitable for small engines. The work is being done by members participating in the IIEC (Inter-Industry Emission Control) Program, and the exhaust emission levels of the concept vehicles developed by these companies have met the goal established by the IIEC Program at low mileage. Each system, however, has a characteristic relationship between exhaust emission level and loss of fuel economy. Much investigation is required, particularly with respect to durability, before any system that will fully satisfy all service requirements can be completed. This paper reports the progress of research and development of the individual concept vehicles.

An analysis of the static behavior of T-shaped joint is presented. Advanced testings by laser holography and infrared ray stress wave analyzers verified the surface deformation and the stress concentration of joint area, which are very important factors of thin-walled joint stiffness. The definition of structural joint stiffness is attempted, and the relationship between structural joint stiffness and sizes(dimension) of the constructing members is obtained in case of a thin-walled T-shaped member with rectangular cross section. The parametric study to accomplish weight reduction, while maintaining the necessary structural joint stiffness, is described in case of Rocker to Center pillar. The numerical analysis of body structure considering the structural joint stiffness shows better accuracy as compared with the analysis with the joint assumed rigid.

This year (1989) Mitsubishi Motors Corp. introduced, on some models, a newly-developed Hydraulic Coupling Uint (HCU), by which 2WD vehicles can be converted into 4WD ones in the same way as done by a viscous coupling (VC). This HCU is similar in the configuration to a vane pump: the oil discharge is returned to the suction chamber through a number of orifices. The rotor and cam ring (housing) are respectively connected to the two shafts; either of the one with the front wheels and the other with the rear wheels. Accordingly, it works as a slip-sensitive differential like a VC while it has a merit of progressive and parabolic torque-response characteristic, which offers stronger traction and acceleration capability and also minimizes tight-corner braking. This paper discusses primarily the configurations, functions and test results of the HCU and also presents an overview on further development possibilities of the 4WD system.

A Vehicle Vibration Control System by Active Control has been developed. The experimental results using a 4-cylinder gasoline engine installed in a car showed that at the position of the driver's seat, the acceleration of the vibration was reduced by 16 dB. This system operates stably and at low cost because of having a feedforward system, so many applications can be expected in the near future as methods for vehicle vibration reduction.

There have been various predictions made concerning the future profile for automobiles but such predictions have in many cases been based solely on anticipated advances in technology. In presenting a profile for automobiles in the year 2000, the writers predict the evolution and transfiguration of automobiles, taking both phases in the changing social environment and technical trends into account. Interest in automobiles is expected to shift from hardware to software and then to humanware (i.e. more emphasis is placed on the relationship with human beings), and automobiles will evolve and transfigure reflecting these changes.