Criteria

Text:
Affiliation:
Display:

Results

Viewing 1 to 30 of 43
1985-01-01
Technical Paper
856041
Y. Vermont
Renault believes that the behavior of the vehicle must always be consistent with the instantaneous orders given by the driver, whether braking, accelerating or lifting the foot off the accelerator. The vehicle must also inform its driver when it is near a point of limit. The first part of this paper details the vehicle with respect to its trajectory at stabilized speeds. The rigidity of the overall drift of the axle assemblies and tires, the steering angles induced by vehicle roll attitude, under- and over-steering behavior and vehicle roll attitude, under- and over-steering behavior and behavior of the tire under load are covered. A vehicle trajectory model is used to confirm test results.
2011-08-30
Journal Article
2011-01-1893
Maria Rivas, Pascal Higelin, Christian Caillol, Olivier Sename, Emmanuel Witrant, Vincent Talon
To improve the prediction of the combustion processes in spark ignition engines, a 0D flame/wall interaction submodel has been developed. A two-zones combustion model is implemented and the designed submodel for the flame/wall interaction is included. The flame/wall interaction phenomenon is conceived as a dimensionless function multiplying the burning rate equation. The submodel considers the cylinder shape and the flame surface that spreads inside the combustion chamber. The designed function represents the influence of the cylinder walls while the flame surface propagates across the cylinder. To determine the validity of the combustion model and the flame/wall interaction submodel, the system was tested using the available measurements on a 2 liter SI engine. The model was validated by comparing simulated cylinder pressure and energy release rate with measurements. A good agreement between the implemented model and the measurements was obtained.
2011-04-12
Technical Paper
2011-01-0923
Benoit Douailler, Frederic Ravet, Vivien Delpech, Dominique Soleri, Benjamin Reveille, Rajesh Kumar
CNG is one of the most promising alternate fuels for passenger car applications. CNG is affordable, is available worldwide and has good intrinsic properties including high knock resistance and low carbon content. Usually, CNG engines are developed by integrating CNG injectors in the intake manifold of a baseline gasoline engine, thereby remaining gasoline compliant. However, this does not lead to a bi-fuel engine but instead to a compromised solution for both Gasoline and CNG operation. The aim of the study was to evaluate the potential of a direct injection spark ignition engine derived from a diesel engine core and dedicated to CNG combustion. The main modification was the new design of the cylinder head and the piston crown to optimize the combustion velocity thanks to a high tumble level and good mixing. This work was done through computations. First, a 3D model was developed for the CFD simulation of CNG direct injection.
2011-04-12
Technical Paper
2011-01-1300
Damiano Di-Penta, Karim Bencherif, Pierre-Yves Le-Morvan
This paper presents an after-treatment architecture combining a close coupled NOx trap and an under floor NOx trap. Instead of simply increasing the volume of the catalyst, we propose to broaden the active temperature window by splitting the LNT along the exhaust line. In order to design this architecture, a complete 1D model of NOx trap has been developed. Validated with respect to experimental data, this model has been useful to define the two volumes of LNT, making significant savings on the test bench exploitation. However, one of the main difficulties to operate the proposed architecture is the NOx purge and sulfur poisoning management. In order to optimize the NOx and sulfur purge launches, we have developed a control strategy based on an embedded reduced LNT model. These strategies have been validated on different driving cycles, by the means of simulation and of vehicle tests using rapid prototyping tools.
2005-05-16
Technical Paper
2005-01-2444
Jean-François Rondeau, Arnaud Duval, Guillaume Deshayes, Mathieu Lassalas, Hans-Elias de Bree, Sébastien Chaigne
In order to reach OEMs acoustic treatment targets (improving performance while minimizing the weight and cost impact), we have developed an original hybrid approach called “Vehicle Acoustic synthesis method”[1] to simulate - and therefore to optimize - noise treatments for both insulation and absorption, and to calculate the resulting Sound Pressure Level (SPL) at ear points for the middle and high frequency range. To calculate the SPL, we identify equivalent volume velocity sources from intensity measurements, and combine them to acoustic transfer functions (panel/ear) measured or computed with ray tracing codes using the reciprocity principle. Compared to our first approach [1], this paper shows a new measurement technique using pressure-particle velocity probes [2]. This technique allows to reduce acquisition time by a factor four, and makes therefore possible a synthesis method on a complete car within two weeks.
2005-05-11
Technical Paper
2005-01-2145
Efthimios Zervas, Pascal Dorlène, Laurent Forti, Cyriaque Perrin, Jean-Claude Momique, Richard Monier, Didier Pingal, Béatrice Lopez
The Particulate Measurement Programme (PMP) works on the identification of a method to replace or complete the existing particle mass (PM) measurement method. The French PMP subgroup, composed by IFP, PSA Peugeot-Citroën, Renault and UTAC, proposes an improved gravimetric method for the measurement of emitted particles, and conducted an inter-laboratory test to evaluate its performances. The technical programme is based on tests carried out on a Euro3 Diesel passenger car (PC), tested on the New European Driving Cycle (NEDC). To achieve low particulate matter (PM) emissions, the EGR is disconnected and a paraffinic fuel is used. The regulated pollutants are also measured. It is shown that the multiple filter weighing and a 0.1 μg balance instead of a 1 μg one are not necessary, as the first weighing and the 1 μg balance performances are satisfactory for type-approval purposes.
2006-04-03
Technical Paper
2006-01-0070
Per Bakke, Andreas Fischersworring-Bunk, Isabelle de Lima, Hans Lilholt, Ingemar Bertilsson, Fethi Abdulwahab, Pierre Labelle
A specific objective of the European Mg-Engine project is to qualify at least two die cast Mg alloys with improved high temperature properties, in addition to satisfactory corrosion resistance, castability and costs. This paper discusses the selection criteria for high temperature alloys leading to four candidate alloys, AJ52A, AJ62A, AE44 and AE35. Tensile-, creep- and fatigue testing of standard die cast test specimens at different temperatures and conditions have led to a very large amount of material property data. Numerous examples are given to underline the potential for these alloys in high temperature automotive applications. The subsequent use of the basic property data in material models for design of automotive components is illustrated.
2012-04-16
Technical Paper
2012-01-0831
Ludek Pohorelsky, Pavel Brynych, Jan Macek, Pierre-Yves Vallaude, Jean-Charles Ricaud, Philippe Obernesser, Pascal Tribotté
This paper introduces a research work on the air loop system for a downsized two-stroke two-cylinder diesel engine conducted in framework of the European project dealing with the POWERtrain for Future Light-duty vehicles - POWERFUL. The main objective was to determine requirements on the air management including the engine intake and exhaust system, boosting devices and the EGR system and to select the best possible technical solution. With respect to the power target of 45 kW and scavenging demands of the two-cylinder two-stroke engine with a displacement of 0.73 l, a two-stage boosting architecture was required. Further, to allow engine scavenging at any operation, supercharger had to be integrated in the air loop. Various air loop system layouts and concepts were assessed based on the 1-D steady state simulation at full and part load with respect to the fuel consumption.
1996-04-01
Technical Paper
91A121
J. P. Jameux, M. El Mouatassim, J. P. Dumesnil
In order to improve the design of drawn parts and to reduce the number of trial and error tests, Renault has undertaken the development and the validation of various finite element procedures and codes. This paper describes the function of each software and its level of integration into the design process. One of them is already an operational tool used be planners whilst the others are still in the validation phase. Selected examples show typical applications of the computer programs on automotive parts.
1998-02-23
Technical Paper
980936
A. P. Martin, N. S. Will, A. Bordet, P. Cornet, C. Gondoin, X. Mouton
The emissions performance of catalytic converters under different conditions of flow distribution was investigated. Computational Fluid Dynamics methods were utilised to model the maldistribution effects of different inlet cones. The effects of maldistribution on ageing, light-off and conversion were investigated using steady state tests on an engine bench. Emission testing was also conducted on a vehicle throughout ECE and EUDC test cycles. Maldistribution was found to have a significant effect on the efficiency of the catalyst during the early stages of the ECE cycle for both fresh and aged catalysts. The effects were less significant over later stages of the ECE cycle and throughout the EUDC except NOx where maldistribution did have an effect on the conversion at higher flow rates during the later stages of the test.
2006-04-03
Technical Paper
2006-01-1194
V. Dugué, N. Gauchet, D. Veynante
3D simulations of internal combustion engines are usually based on statistical approaches (RANS) that may not allow predicting cycle-to-cycle variations (CCV) or transient speeds because part of this information is lost by the averaging procedure. To simulate such phenomena, it requires time resolved approaches. Therefore, large eddy simulation (LES), which only involves a spatial averaging, appears to be a very promising tool. An LES approach is applied to simulate the flow field inside one cylinder taken from a real four-valve diesel engine mounted on an experimental particle image velocimetry (PIV) bench. Preliminary tests are carried out to evaluate the industrial code capabilities. A multi-cycle calculation is computed in cold flow, in order to evaluate its ability to simulate cycle-to-cycle variations (CCV).
2007-01-23
Technical Paper
2007-01-0035
Rudolf R. Maly, Volker Schaefer, Heinz Hass, G. F. (Barry) Cahill, Pierre Rouveirolles, Anders Röj, Rainer Wegener, Xavier Montagne, Alessandra Di Pancrazio, Julian Kashdan
Over the next decades to come, fossil fuel powered Internal Combustion Engines (ICE) will still constitute the major powertrains for land transport. Therefore, their impact on the global and local pollution and on the use of natural resources should be minimized. To this end, an extensive fundamental and practical study was performed to evaluate the potential benefits of simultaneously co-optimizing the system fuel-and-engine using diesel as an example. It will be clearly shown that the still unused co-optimizing of the system fuel-and-engine (including advanced exhaust after-treatment) as a single entity is a must for enabling cleaner future road transport by cleaner fuels since there are large, still unexploited potentials for improvements in road fuels which will provide major reductions in pollutant emissions both in vehicles already in the field and even more so in future dedicated vehicles.
2004-06-08
Technical Paper
2004-01-1904
Pierre Duret, Bertrand Gatellier, Luis Monteiro, Marjorie Miche, Peter Zima, Damien Maroteaux, Jacky Guezet, David Blundell, Fritz Spinnler, Hua Zhao, Matteo Perotti, Lucio Araneo
The purpose of the European « SPACE LIGHT » (Whole SPACE combustion for LIGHT duty diesel vehicles) 3-year project launched in 2001 is to research and develop an innovative Homogeneous internal mixture Charged Compression Ignition (HCCI) for passenger cars diesel engine where the combustion process can take place simultaneously in the whole SPACE of the combustion chamber while providing almost no NOx and particulates emissions. This paper presents the whole project with the main R&D tasks necessary to comply with the industrial and technical objectives of the project. The research approach adopted is briefly described. It is then followed by a detailed description of the most recent progress achieved during the tasks recently undertaken. The methodology adopted starts from the research study of the in-cylinder combustion specifications necessary to achieve HCCI combustion from experimental single cylinder engines testing in premixed charged conditions.
2004-06-08
Technical Paper
2004-01-1924
Robert Edwards, Vincent Mahieu, Jean-Claude Griesemann, Jean-François Larivé, David J. Rickeard
A consortium of CONCAWE, EUCAR and the EU Commission's JRC carried out a Well-to-Wheels analysis of a wide range of automotive fuels and powertrains. The study gives an assessment of the energy consumption and greenhouse gas emissions for each pathway. It also considers macroeconomic costs and the market potential of alternative fuels.
2005-04-11
Technical Paper
2005-01-0220
P.-A. Beau, M. Funk, R. Lebas, F.-X. Demoulin
Atomizing systems must be able to form sprays with predetermined characteristics. There are affected by the shape of the injector as well as external conditions. Thus, in order to avoid numerous experiments, this is necessary to develop predictive atomization models able to deal with the complete atomization process. This can be done using a Eulerian model for primary break-up. This approach describes the flow continuously from inside the injector to the dispersed spray region. In this paper the Eulerian multiphase approach and the Eulerian single-phase approach are compared and the results lead to an intermediate quasi-multiphase approach for describing the spray core. Finally a transition zone permits to represent the diluted spray region by using the classical Lagrangian approach to benefit of the experience accumulated on this method, in particular for the vaporization and the combustion.
2007-05-15
Technical Paper
2007-01-2274
T. Geluk, P. J. G. van der Linden, S. Bonnet
Impact noise, inside a car, due to tire-launched gravel on the road can lead to loss of quality perception. Gravel noise is mainly caused by small-sized particles which are too small to be seen on the road by the driver. The investigation focuses on the identification of the mechanisms of excitation and transfer. The spatial distribution of the particles flying from a tire is determined, as well as the probable impact locations on the vehicle body-panels. Finally the relative noise contributions of the body-panels are estimated by adding the panel-to-ear transfer functions. This form of Transfer-Path-Analysis allows vehicle optimization and target setting on the level of the tires, exterior panel treatment and isolation.
2007-06-12
Technical Paper
2007-01-2493
Elodie Chateauroux, Xuguang Wang, Jules Trasbot
HANDIMAN project aims at collection data and developing a computer aided design tool that helps the designers to adapt car design to the needs of elderly and impaired people when getting in and out of a car. Healthy young people, elderly people and people with hip or/and knee prostheses participated in the experiments. For elderly subjects and those with prostheses, several clinical tests were carried out for characterizing their joint mobilities and physical capacities. Ingress / egress motions were captured for four different types of car. According to individual characteristics and motion control strategies, a motion database will be developed. With help of recently developed case based motion simulation approach, this motion database can be used to simulate new car configurations within the scope covered by the database. The aim of this paper is to present the collected data and how we are going to structure them to simulate ingress / egress motions.
2016-04-05
Technical Paper
2016-01-1034
Georges Salameh, Pascal Chesse, David Chalet, Vincent Talon
Abstract Engine downsizing is potentially one of the most effective strategies being explored to improve fuel economy. A main problem of downsizing using a turbocharger is the small range of stable functioning of the turbocharger centrifugal compressor at high boost pressures, and hence the measurement of the performance maps of both compressor and turbine. Automotive manufacturers use mainly numerical simulations for internal combustion engines simulations, hence the need of an accurate extrapolation model to get a complete turbine performance map. These complete maps are then used for internal combustion engines calibration. Automotive manufacturers use commercial softwares to extrapolate the turbine narrow performance maps, both mass flow characteristics and the efficiency curve.
2016-04-05
Technical Paper
2016-01-0562
Hassan Karaky, Gilles Mauviot, Xavier Tauzia, Alain Maiboom
Abstract Due to its harmful effect on both human health and environment, soot emission is considered as one of the most important diesel engine pollutants. In the last decades, the industrial engine manufacturers have been able to strongly reduce its engine-out value by many different techniques, in order to respect the stricter emission norms. Simulation modeling has played and continues to play a key role for this purpose in the engine control system development. In this context, this paper proposes a new soot emission model for a direct injection diesel engine. This soot model is based on a zero-dimensional semi-physical approach coupled with a crank-angle resolved combustion model and a thermodynamic calculation of the burned gas products temperature. Furthermore, a multi linear regression model has been used to estimate the soot emissions as function of significant physical combustion parameters.
2016-04-05
Technical Paper
2016-01-0554
José Galindo, Andrés Tiseira, Roberto Navarro, Daniel Tarí, Hadi Tartoussi, Stéphane Guilain
Abstract 0D-1D codes allow researchers to obtain a prediction of the behavior of internal combustion engines with little computational effort. One of the submodels of such codes is devoted to the centrifugal compressor. This model is often based on the compressor performance maps, therefore requiring the extrapolation of the maps so that all possible operating conditions are covered. Particularly, a suitable extrapolation of isentropic efficiency map is sought. This work first examines different available methods for compressor efficiency extrapolation into off-design conditions. No method is found to provide satisfactory results at all extrapolated regions: low and high compressor speeds and low compression ratio at measured speeds. Hence, a new method is proposed and its accuracy is assessed with the aid of compressor off-design measurements.
2011-06-09
Technical Paper
2011-37-0029
Sergio Hoyas, Jose M. Pastor, Dung Khuong-Anh, Juan Manuel Mompó-Laborda, Frederic Ravet
During the last fifteen years, Computational Fluid Dynamics (CFD) has become one of the most important tools to both understand and improve the diesel spray development in Internal Combustion Engine (ICE). Most of the approaches and models used pure Eulerian or Lagrangian descriptions to simulate the spray behavior. However, each one of them has both advantages and disadvantages in different regions of the spray, it can be the dense zone or the downstream dilute zone. One of the most promising techniques, which has been in development since ten years ago, is the Eulerian-Lagrangian Spray Atomization (ELSA) model. This is an integrated model for capturing the whole spray evolution, including primary break-up and secondary atomization. In this paper, the ELSA numerical modeling of diesel sprays implementation in Star-CD (2010) is studied, and simulated in comparison with the diesel spray which has been experimentally studied in our institute, CMT-Motores Térmicos.
2017-03-28
Technical Paper
2017-01-0669
Matthieu LEGUILLE, Frederic Ravet, Jerome Le Moine, Eric Pomraning, Keith Richards, P. K. Senecal
Abstract The current trend of downsizing used in gasoline engines, while reducing fuel consumption and CO2 emissions, imposes severe thermal loads inside the combustion chamber. These critical thermodynamic conditions lead to the possible auto-ignition (AI) of fresh gases hot-spots around Top-Dead-Center (TDC). At this very moment where the surface to volume ratio is high, wall heat transfer influences the temperature field inside the combustion chamber. The use of a realistic wall temperature distribution becomes important in the case of a downsized engine where fresh gases hot spots found near high temperature walls can initiate auto-ignition. This paper presents a comprehensive numerical methodology for an accurately prediction of thermodynamic conditions inside the combustion chamber based on Conjugate Heat Transfer (CHT).
2017-03-28
Technical Paper
2017-01-0538
Corinna Netzer, Lars Seidel, Michal Pasternak, Christian Klauer, Cathleen Perlman, Frederic Ravet, Fabian Mauss
Abstract Engine knock is an important phenomenon that needs consideration in the development of gasoline fueled engines. In our days, this development is supported by the use of numerical simulation tools to further understand and subsequently predict in-cylinder processes. In this work, a model tool chain based on detailed chemical and physical models is proposed to predict the auto-ignition behavior of fuels with different octane ratings and to evaluate the transition from harmless auto-ignitive deflagration to knocking combustion. In our method, the auto-ignition and emissions are calculated based on a new reaction scheme for mixtures of iso-octane, n-heptane, toluene and ethanol (Ethanol consisting Toluene Reference Fuel, ETRF). The reaction scheme is validated for a wide range of mixtures and every desired mixture of the four fuel components can be applied in the engine simulation.
2015-04-14
Technical Paper
2015-01-1698
Balamurugan Rathinam, Frederic Ravet, Cedric Servant, Laurent Delahaye, Upendra Naithani
This paper is focused on the experimental and numerical investigation of tumble motion on a single cylinder optical engine on three important parameters like engine load conditions, engine speed and level of tumble. Experiments are conducted in an optical engine and the velocity fields are measured with the aid of advanced particle image velocimetry (PIV) measurement technique. For simulation, multiple cases were considered to develop the numerical process for transient in-cylinder aerodynamics to capture the tumble motion and turbulence level in a Spark Ignited (SI) engine. The simulation results, velocity fields of each case were directly compared with the corresponding test results for different crank positions of the engine. On comparison, a good agreement between the measurement and the simulation is obtained for different configurations.
1999-09-28
Technical Paper
1999-01-3169
E. DiPasquale, J.-L. Duval, F. El Khaldi
This paper presents the application of the different approaches available for the analysis of the sheet metal forming process on an industrial part (RENAULT KANGOO front fender). It is nowadays accepted in the engineering community that inverse, simplified direct and incremental direct approach are complementary and should be used in the development of a stamped part. The paper shows the formability analysis of the TWINGO door and hatchback at different stages of the part and process design, identifies the optimal approach at different stages and gives indication as to the relative speed, accuracy and quality of the different simulation solutions.
1999-03-01
Technical Paper
1999-01-0500
C. Arcoumanis, M. Gavaises, B. Argueyrolles, F. Galzin
A new simulation approach to the modeling of the whole fuel injection process within a common-rail fuel injection system for direct-injection gasoline engines, including the pressure-swirl atomizer and the conical hollow-cone spray formed at the nozzle exit, is presented. The flow development in the common-rail fuel injection system is simulated using an 1-D model which accounts for the wave dynamics within the system and predicts the actual injection pressure and injection rate throughout the nozzle. The details of the flow inside its various flow passages and the discharge hole of the pressure-swirl atomizer are investigated using a two-phase CFD model which calculates the location of the liquid-gas interface using the VOF method and estimates the transient formation of the liquid film developing on the walls of the discharge hole due to the centrifugal forces acting on the swirling fluid.
2000-03-06
Technical Paper
2000-01-0832
Oscar Martinez Garcia, Keyvan Kargar
2000-03-06
Technical Paper
2000-01-0914
Francisco Payri, José Galindo, Vicente Bermudez, Philippe Gutierrez, Hervé Mathieu
The purpose of this paper is to present the results of a study on the exhaust junctions geometry. Twelve three-branch junctions of different geometry have been tested on a single cylinder engine. The parameters studied have been exhaust junction outlet-to-inlet diameter ratio, length, angle between inlet branches and the existence of a reed separating inlet branches. An analysis of the pressure waves amplitude (incident, reflected and transmitted) obtained from instantaneous pressure measurements in some locations around the junction has been carried out. The analysis of results shows that junction length has a low influence on its behavior. The ratio between inlet and outlet branches diameters increases both reflection and directionality (avoiding pressure wave transmission to the adjacent branch). The existence of a reed separating the inlet flows may increase directionality with moderate pressure losses if the throat area is not reduced.
2000-10-16
Technical Paper
2000-01-2932
R. Marcer, P. Le Cottier, H. Chaves, B. Argueyrolles, C. Habchi, B. Barbeau
Progress in Diesel spray modelling highly depends on a better knowledge of the instantaneous injection velocity and of the hydraulic section at the exit of each injection hole. Additionally a better identification of the mechanisms which cause fragmentation is needed. This necessitates to begin with a precise computation of the two-phase flow which arises due to the presence of cavitation within the injectors. For that aim, a VOF type interface tracking method has been developed and improved (Segment Lagrangian VOF method) which allows to describe numerically the onset and development of cavitation within Diesel injectors. Furthermore, experiments have been performed for validation purpose, on transparent one-hole injectors for high pressure injection conditions. Two different entrance geometries (straight and rounded) and various upstream and downstream pressure levels have been considered.
2000-03-06
Technical Paper
2000-01-0293
Michel Lebrun, Renaud Meillier, Lionel Broglia Patron, Sébastien Samuel
The modeling of thermal phenomena in transient state in a vehicle, typically the studies of heat exchanges in the engine or the heat exchange in the exhaust line leads to the use of nodal methods or lumped parameters in systems approach. This lumped parameters vision has led to important formalization studies these past years leading to two important concepts: the multiport concept of which bond-graphs constitute the theoretical framework, and the polymorphic modeling concept leading to the definition of a minimum of basic elements allowing to build a maximum of situations. This article proposes to demonstrate how these concepts have been used to bring about the development of a library of basic elements. Its application is demonstrated by the modeling of the different modules composing the engine (lubrication, cooling, exhaust and metal masses).
Viewing 1 to 30 of 43

Filter

  • Range:
    to:
  • Year: