Search Results

This paper evaluates the tendency of lip seals to fracture in a test apparatus in which dynamic runout is 0.010 in and the temperature is cycled between -30 and 0 F. Seals made of eight different polyacrylate polymers were soap-sulfur cured with various types and amounts of carbon black. Physical tests included room-temperature flexibility defined by Young's modulus at small strains, standard tensile tests at room temperature, flexibility at sub-zero temperatures determined by a Gehman test, and sub-zero starting torques of the seals. Primary determinant of successful fracture resistance is a low starting torque resulting from good low-temperature flexibility. The effect of adding graphite to some of these formulations is described and some current commercially available seals are evaluated.

The incentive for use of an interstage diffuser in a free-shaft gas turbine engine is briefly examined and some pertinent published background data reviewed. Tests of two annular diffusers behind an upstream turbine show the deleterious effects of turbine exit flow nonuniformity on diffuser behavior. The flow acceleration provided by the area contraction of a power turbine nozzle located at the diffuser exit substantially improves the nature of the flow previously found to exist at the diffuser exit in the absence of the nozzle.

At the 1970 SAE International Automobile Safety Conference, the first experimental chest impact results from a new, continuing biomechanics research program were presented and compared with earlier studies performed elsewhere by one of the authors using a different technique. In this paper, additional work from the current program is documented. The general objective remains unchanged: To provide improved quantification of injury tolerance and thoracic mechanical response (force-time, deflection-time, and force-deflection relationships) for blunt sternal impact to the human cadaver. Fourteen additional unembalmed specimens of both sexes (ranging in age from 19-81 years, in weight from 117-180 lb, and in stature from 5 ft 1-1/2 in to 6 ft) have been exposed to midsternal, blunt impacts using a horizontal, elastic-cord propelled striker mass. Impact velocities were higher than those of the previous work, ranging from 14-32 mph.

An analysis of oil pumpability reveals that engine oil pumping failures may occur because either the oil cannot flow under its own head to the oil screen inlet, or the oil is too viscous to flow through the screen and inlet tube fast enough to satisfy pump demands. To determine which factor is controlling, the behavior of commercial, multigraded oils was observed visually at temperatures from -40 to 0°F (-40 to - 17.8°C) in a laboratory oil pumpability test apparatus. Test results revealed that pumping failures occur by the first alternative: a hole is formed in the oil, and the surrounding oil is unable to flow into the hole fast enough to satisfy the pump. Of 14 oils tested, 7 failed to be pumped because of air binding or cavitation which developed in this manner. A model, which explains these failures in terms of yield point considerations and the low shear apparent viscosity of the oils, is proposed.

In-cylinder sampling appears to be the only available means for obtaining detailed information of the diesel combustion process. This information is necessary to understand pollutant formation because of the intimate relationship between formation rates and local cylinder conditions. This paper discusses efforts to (1) examine and improve sampling valve design, (2) evaluate potential effects of the valve and the sampling system on sample composition, (3) find methods to extract useful information from sampling data. Sampling hardware is currently being used to study combustion in engines, but further work is needed to quantify the influence of hardware and procedures on sample composition and to design experiments to provide data containing maximum information.

Several polymeric materials were developed and evaluated for possible inclusion in the neck structure of state-of-the-art anthropomorphic dummies. These included three types of foam-polyvinylchloride, polyethylene, and polyurethane, and two flexible polymers-polyurethane and a polyvinylchloride chlorinated polyethylene blend (PVC-CPE). Two materials, the polyurethane elastomer and the PVC-CPE blend, were found to be satisfactory in their dynamic response. Because of the ease of casting, the polyurethane material will be used in the GMR 1 state-of-the-art dummy.

One of the prime requisites for automobile radar systems is obstacle hazard evaluation, the extent needed being dependent upon the particular system application. Much of the information necessary for a radar system to assess the degree of hazard of a target must come from characteristics which can be measured by the radar itself. While the hazard evaluation capacity has not yet been developed for automobile radar systems, research to provide this capability is in progress. Continuous wave (CW) scattering measurements have been made in a manner which is consistent with automobile radar operation. Various aspects of simple targets and of an automobile were measured in a microwave anechoic chamber. Both horizontal and vertical linear polarizations were transmitted and their co-linear and cross polarizations received. These data have been used to confirm the existence of and to understand certain scattering mechanisms.

During development of the General Motors rotary engine, the lubricant was recognized as important to its success because certain lubricants produced deposits which tended to stick both side and apex seals. Consequently, it was decided to develop a rotary engine-dynamometer test, using a Mazda engine, which could be used for lubricant evaluation. In an investigation using an SE engine oil with which there was rotary engine experience, engine operating variables and engine modifications were studied until the greatest amount of deposits were obtained in 100 h of testing. The most significant engine modifications were: omission of inner side seals, plugging of half the rotor bearing holes, pinning of oil seals, grinding of end and intermediate housings, and using a separate oil reservoir for the metering pump. Using this 100 h test procedure, three engine oils and five automatic transmission fluids were evaluated.

The assembly and particularly the reduction of the mass and stiffness matrix for a large system can be a significant portion of the computational cost of finding the mode shapes and natural frequencies. Therefore, parameter studies for design purposes can be prohibitive if these matrices are reassembled and reduced for each change. The purpose of this paper is to outline the procedure for using the modes of the original system to determine the dynamic characteristics of the changed system. The method also results in computational savings for boundary condition changes and for large systems that are nearly-symmetric except for a few mass and stiffness changes. To illustrate the method several changes are made to a ladder frame. The results from an analysis using the reconstructed mass and stiffness matrices and the modal synthesis technique are compared to show the accuracy and freedom requirements.

A brief review of the testing of automatic transmission fluid for compatibility with seals is presented. The total immersion test used in fluid qualification, while apparently effective in predicting the compatibility of fluids and seals in service, does not correlate well with transmission tests with respect to hardness change of piston seals. The Dip-Cycle Test, developed to overcome this limitation, is a procedure for alternately immersing seal specimens in the test fluid and suspending them in the hot air-fluid vapor atmosphere above the fluid. Correlation of the Dip-Cycle Test with transmission piston seal results is much improved over that with the total immersion test. It is the purpose of this paper to review these developments and to present an improved test procedure (dip cycle test) for evaluating the effect of fluids on transmission piston seal materials.

This paper describes a computer study made by the General Motors Corp. Research Laboratories to determine what percentage of the energy supplied to the axle of a passenger car is available for recovery through regeneration. Several weight classes of passenger cars were studied using three driving schedules-city, suburban, and highway. For each vehicle run in accordance with the prescribed driving schedules, two ratio percentages were obtained: (1) the ratio of energy available for recovery to the total energy supplied to the axle, and (2) the above ratio modified by assumed efficiencies in the propulsion and regeneration systems.

Tests were conducted using older model cars with automatic transmissions to determine the effect of fluid composition on leakage past the rotating shaft seals. It was found that seal leakage was reduced or stopped by changing to seal-swelling fluids, and increased with seal-shrinking fluids. Leakage was also reduced by adding aromatic additives to existing fluids in the transmissions. Seal volume and hardness change results from bench tests support the car data.

The Total Immersion Test (ASTM D 471) for seal elastomers, used in evaluating the compatibility of fluids and seals for automatic transmissions, does not, produce hardness and volume change results similar to those found for rotating shaft seals in service. The Tip Cycle Test was devised to provide better agreement with service results. In the test, one side of the seal is exposed to air, and the other alternately to fluid and to air-fluid vapor. Rotating shaft seals were evaluated in both car and dynamometer transmission tests, and in various bench tests. Agreement was poor between transmission tests and both the Total Immersion and the Dip Cycle Tests. Good agreement was found with the Tip Cycle Test.

Effective performance of functional automotive components requires fluid sealing under compatible conditions. One method of determining this compatibility is through the use of immersion testing under a variety of conditions that simulate those experienced in actual use. By measuring the changes in the physical properties of the seal materials after immersion a judgment can be made regarding seal/fluid compatibility which will be encountered later in actual use. A series of immersion tests using representative seal materials and automotive fluids; namely, gear oils, transmission fluids, and motor oils were conducted within the framework of the Technical Committee on Automotive Rubber, jointly sponsored by SAE-ASTM.

Conventional radial lip oil seals can be made more effective by utilizing helical grooving beneath the contact lip surface. Miniature hydrodynamic pumps so formed aid the radial lip seal in containing the oil by generating fluid forces opposite in direction to the leakage flow forces. This seal-shaft combination has been termed the Hydroseal. Four factorial experiments were conducted to evaluate the effect of helix angle, groove depth, groove width, and number of grooves on sealing performance. The criterion used as a basis for selecting the optimum design were leakage, wear, hardening of the sealing surface, and pumping capacity. These data indicated that the best hydroseal design was one with three grooves, 0.0003 in. deep, 0.014 in. wide, having a helix angle of 45 deg.

The Sealometer is used for evaluating the performance of lip type oil seals and provides a dimensionless number derived from measuring the increase in temperature of a test shaft operating in a lip seal for a given time interval. With the Sealometer it is possible to study parameters that affect seal performance. As a quality control instrument, the machine provides accurate data for design. Sealometer evaluation offers a quick method of determining the life expectancy of a particular design for a particular application and eliminates the need for long life test programs.

Utilization of numerically controlled milling has been found particularly attractive in producing, in limited quantities, the three-dimensional curved surfaces characteristic of turbomachinery. In experimental and developmental programs its use can result in decreased fabrication cost, reduced lead time, and improved dimensional accuracy. Following a review of the general classifications of numerically controlled milling machines available for manufacture of such parts, illustrations are given of some of the procedures and techniques employed in their use. A variety of parts made using numerical control serve as examples.

The use of multigrade (V.I. improved) oils in automotive engines has increased significantly in recent years. However, the performance of these oils in terms of factors such as oil economy, wear, and noise, is not always equal to that of single grade oils. Although the initial viscosity of multigrade oils is related to both the base oil and the V.I. improver, the viscosity decreases with use, with the primary factors determining the magnitude of the change being the degree of shear and the characteristics and concentration of the V.I. improver used. This decrease in viscosity has been assumed to be the cause of the decreases in oil economy that may occur with oil use. However, viscosity changes are not believed to be the primary factor responsible since similar oil economy changes have also been observed for single grade oils. Nevertheless, the characteristics and concentration of the V.I. improver used can be a significant factor influencing oil economy.

EXTENSIVE TESTING by GM Research Laboratories has screened five promising transaxle fluids out of 32 mineral-oil-base fluids, 10 synthetic-base fluids, and numerous additive-base stock combination fluids. This paper discusses the findings of the testing and the continuing program on the five fluids. Transaxle fluids have a number of properties affecting performance, including: High-temperature viscosity. Low-temperature fluidity. Shear resistance. Friction properties. Oxidation resistance. Antifoam quality. Effect on seals. Fluid-clutch plate compatibility. Antiwear quality. Extreme-pressure quality. Antirust and anticorrosion qualities.*

THIS REPORT deals with the major parameters of a seal application which affect its efficiency and life, as determined by controlled laboratory testing in CM Research Laboratories.* A. Shaft 1. Surface Roughness 2. Machining Lead B. Assembly C. Seal 1. Seal Diameter Control Trim Interference Spring Rate 2. Seal Lip Pressure Trim Interference Spring Rate Rubber Hardness Eccentricity 3. Seal Eccentricity Mold Register Assembly Trim