Search Results

Due to the new CO2 targets for vehicles, electrification of powertrains and operation strategies for electrified powertrains have drawn more attention. This article presents a predictive multi-objective operation strategy for hybrid electric vehicles (HEVs), which simultaneously minimizes the fuel consumption and the cycle aging of traction batteries. This proposed strategy shows better performance by using predictive information and high robustness to inaccuracy of predictive information. In this work, the benefits of the developed operation strategies are demonstrated in a strong hybrid electric vehicle (sHEV) with P2-configuration. For the cycle aging of a lithium-ion battery, an empirical model is built up with Gaussian processes based on experimental data.

Due to the EU6 emission standard that will be mandatory starting in September 2014 the particulate emissions of GDI engines come into the focus of development. For this reason, soot and the mechanisms responsible for the soot formation are of particular importance. A very significant source of particulate emissions from engines with gasoline direct injection is the wall film formation. Therefore, the analysis of soot emission sources in the CFD calculation requires a detailed description of the entire underlying model chain, with special emphasis on the spray-wall interaction and the wall film dynamics. The validation of the mentioned spray-wall interaction and wall film models is performed using basic experimental investigations, like the infrared-thermography and fluorescence based measurements conducted at the University of Magdeburg.

Dynamic route guidance is a main feature when discussing traffic telematics systems. At the present time, several system concepts are in the development or implementation stage. The key elements of dynamic route guidance systems are illustrated in the following. Two approaches could be used when designing the system architecture: 1. Centralized routing in traffic information centers combined with on-board terminals. 2. Mobile routing by on-board navigation units which use information received from traffic information centers. The different approaches are presented in this paper. The influences on component design and the effects on communication needs are discussed. This leads to the “hybrid” system architecture which is presented including implementation examples.

With its origin in the process industry, the IEC 61508 „Functional safety of electrical/electronic/programmable electronic safety-related systems” is not fully applicable in the automotive industry, forcing the automotive industry to work on an automotive specific adaptation (ISO 26262 “Functional Safety – Road Vehicles”). This ISO 26262 describes an ideal development process that starts from scratch. In reality development activities are often split locally and in time. This can only be handled with a world wide standard as a basis of a common approach, wide enough to give enough freedom to adapt to diverse boundary conditions, but tight enough to hinder local interpretations to be that far, that a complete safety case becomes impossible. Therefore a strict world-wide standard which allows compatible interpretations is mandatory.

In order to master the increasing complexity of electrical/electronic (E/E) systems in vehicles, E/E architecture design has become an established discipline. The task of the E/E architecture design is to come up with solutions to challenging and often contradictory requirements such as reduced cost and increased flexibility / scalability. One way to optimize the E/E architecture in terms of cost (electronics & wiring harness) is to integrate functions. This can be done by either combining functions from multiple ECUs into a single ECU or by introducing Domain Control Units. Domain Control Units provide the main software functionality for a vehicle domain, while relegating the basic functions of actuator control to connected intelligent actuators. Depending on the different market segments (low price, volume and premium) and the different vehicle domains, the actual usage of Domain Control Units can be quite different and sometimes questionable.

A major trend in modern vehicle control is the increase of complexity and interaction of formerly autonomous systems. In order to manage the resulting network of more and more integrated (sub)systems Bosch has developed an open architecture called CARTRONIC for structuring the entire vehicle control system. Structuring the system in functionally independent components improves modular software development and allows the integration of new elements such as integrated starter/generator and the implementation of advanced control concepts as drive train management. This approach leads to an open structure on a high level for the design of advanced vehicle control systems. The paper describes the integration of the spark-ignition (SI) engine management system (EMS) into a CARTRONIC conform vehicle coordination requiring a new standard interface between the vehicle coordination and the EMS level.

In view of tight emission standards, injection strategies to reduce raw HC-emissions during the cold starting of port fuel injected engines are evaluated in this study. The relevance of spray targeting and atomization is outlined in the first part of this paper. The foundation and performance of different injector concepts with respect to spray characteristics are discussed. Laboratory experiments demonstrate that concepts relying on auxiliary energy, such as air-assistance, fuel heating and injection at elevated system pressures, are capable of producing spray droplet sizes in the SMD-range of 25μm. For future injection strategies aimed at the compliance of SULEV emission levels, this target value is considered to be essential. In the second part of this paper, emission tests of selected injector concepts are carried out using a V6-3.2I ULEV engine operated both in a vehicle and on a test bench.

On the way to automated driving, the installation rate of surround sensing systems will rapidly increase in the upcoming years. The respective technical progress in the areas of driver assistance and active safety leads to a numerous and valuable information and signals to be used prior to, during and even after an accident. Car makers and suppliers can make use of this new situation and develop integrated safety functions to further reduce the number of injured and even deaths in car accidents. Nevertheless, the base occupant safety remains the core of this integrated safety system in order to ensure at least a state-of-the-art protection even in vehicles including partial, high or full automation. Current networked safety systems comprehend a point-to-point connection between single components of active and safety systems. The optimal integration requires a much deeper and holistic approach.

The worldwide stricter emission legislation and growing demands for lower fuel consumption require for significant efforts to improve combustion efficiency while satisfying the emission quality demands. Homogeneous Charge Compression Ignition (HCCI) on gasoline engines provides a particularly promising and, at the same time, challenging approach, especially regarding the combustion mode switch between spark-ignited (SI) and gasoline HCCI mode and vice-versa. Naturally aspirated (n.a.) HCCI shows considerable potential, but the operation range is air breathing limited due to hot residuals required for auto-ignition and to slow down reaction kinetics. Therefore it is limited to part-load operation. Considering the future gasoline engine market with growing potentials identified on downsized gasoline engines, it is imperative to investigate the synergies and challenges of boosted HCCI.

Secondary air injection after cold start gives two effects for reduced exhaust emissions: An exothermic reaction at the hot exhaust valves occurs, which increases the temperature of the exhaust gas. It gives sufficient air to the catalyst during the cold start fuel enrichment that is necessary to prevent driveability problems. Handicaps for the wide use of air injection include space constraints, weight and price. An electrical air blower was choosen to best satisfy all these requirements. The development steps are described. The result is a three stage radialblower with extremly high revolutions of about 18000 rpm. The system configuration and the outcome are demonstrated on the new C-Class of Mercedes-Benz. The results show emission reductions higher than 50 %, while also satisfying the development goals of noise, volume, weight and cost requirements.

The continuing increase in the performance of restraint systems has led to a drastic increase in the number of actuator devices. The individual wiring of the igniters becomes more and more problematic through the accompanied large number of plug connections and cables. Along with demands for weight and volume reduction, there are requirements for EMI and short circuit protection to eliminate erroneous deployment and misuse. As a solution, a new multi-protocol dual wire bus system is described that has the capability to supply energy and address multiple peripheral output stages to simultaneously fire any combination of actuators.

In the last years, the requirements for electrical energy systems in motor vehicles have increased considerably. In the past, many studies were focused on single components of the electrical system. However, to shorten the development process, reduce costs, improve reliability and also to optimize the fuel consumption due to the electrical system, the electrical system must be regarded as a whole. The Robert Bosch GmbH has developed a simulation environment, which is intended to improve the development process of new vehicle electrical systems by means of computer simulation. On the basis of a freely selectable driving cycle and various driver models, it is possible to simulate the behavior of electrical energy supply structures. The model of the electrical system is coupled to a dynamic model of the drivetrain. The characteristics of this drivetrain can also be modified and various vehicle models can be selected for simulation.

The new aerial communication protocol “Controller Area Network” (CAN) efficiently supports distributed realtime control in automotive applications. In order to unload CPUs from high-speed message transfer, dedicated CAN hardware handles messages up to the communication object level. In multiplex wiring message rates are one to two orders of magnitude lower, allowing to implement the upper communication level more cost-effectively in software. This reduces CAN interface hardware to bitwise protocol handling only. It may be incorporated even into low-end microcontrollers without significantly increasing chip size. Thus the same CAN protocol supports the entire range of serial automotive communication, matching implementation costs to requirements at each performance level.

Additional future requirements for automobiles such as improved vehicle dynamics control, enhanced comfort, increased safety and compact packaging are met by modern electrical steering systems. Based on these requirements the new functionality is realized by various additional electrical components for measuring, signal processing and actuator control. However, the reliability of these new systems has to meet the standard of today's automotive steering products. To achieve the demands of the respective components (e.g. sensors, bus systems, electronic control units, power units, actuators) the systems have to be fault-tolerant and/or fail-silent. The realization of the derived safety structures requires both expertise and experience in design and mass production of safety relevant electrical systems. Beside system safety and system availability the redundant electrical systems also have to meet economic and market requirements.

Until now, the use of biometric systems has not been in the public eye. The high cost of sensors and processing has meant that biometrics was previously restricted to high security access, financial transaction and law enforcement applications. However, as a result of improvements in technology, biometric sensor price and reliability have achieved levels where biometrics is being seriously considered for automotive systems. This paper introduces the field of biometrics, the key terms and processes. Fingerprint Technology and Identification by Fingerprint are discussed, as are the use and applicability of biometrics in automotive applications, including Personal Profiling, Keyless Engine Start and vehicle access authorization. The key findings of investigations over the last years are discussed.

Large Eddy Simulations (LES) and tracer-based Laser-Induced Fluorescence (LIF) measurements were performed to study the dynamics of fuel wall-films on the piston top of an optically accessible, four-valve pent-roof GDI research engine for a total of eight operating conditions. Starting from a reference point, the systematic variations include changes in engine speed (600; 1,200 and 2,000 RPM) and load (1000 and 500 mbar intake pressure); concerning the fuel path the Start Of Injection (SOI=360°, 390° and 420° CA after gas exchange TDC) as well as the injection pressure (10, 20 and 35 MPa) were varied. For each condition, 40 experimental images were acquired phase-locked at 10° CA intervals after SOI, showing the wall-film dynamics in terms of spatial extent, thickness and temperature.

The amount of software integrated into today's vehicles growths exponential and tends to be a patchwork of non interrelated applications. However the interrelationship gets more and more intensive as applications start to cooperate and therefore communicate with each other. By introducing a domain exceeding middleware concept we want applications to experience a high level of integration and enable outsourcing of features applications have in common.

Bosch Automotive Semiconductor Unit investigated destroyed semiconductor devices (ASIC) from electronic control unit complaints, which failed due to electrical overstress. It turned out that failure fingerprints could only be reproduced by semiconductor operation far beyond spec limits. One main failure mechanism is caused by hot plugging and bad or late ground connection. In today’s cars some applications are still active for minutes after ignition switch off. So, currents of several amps are delivered and in a typical production or garage environment, hot plugging cannot be avoided completely. Bosch suggests introducing extended ground pins to get an enforced switch on/off sequence during plugging. This poka yoke protection principle is successfully used in other industries for a long time and should now come into cars.

The electrification of vehicles marks the introduction of new products to the automotive market and a continued effort to optimize their performance. The electric motor is an important component with which a further optimization of efficiency, power density and cost can be achieved. Additional benefits can be realized in the laminated core. This paper presents an innovative method to produce laminated stacks by a chain of processes different from conventional ways. The process chain presents a sequence of precision blanking, buffering, heat treatment and gluing. The effect of these processes is compared with existing solutions that typically contain some individual features but usually not the combination that enhances the overall effect. The heat treatment decreases residual stresses from previous process steps and reduces power losses in the laminated core. Depending on the design, benefits around 20% are found.