Search Results

An investigation was performed to identify the benefits of cooled exhaust gas recirculation (EGR) when applied to a potential ethanol flexible fuelled vehicle (eFFV) engine. The fuels investigated in this study represented the range a flex-fuel engine may be exposed to in the United States; from 85% ethanol/gasoline blend (E85) to regular gasoline. The test engine was a 2.0-L in-line 4 cylinder that was turbocharged and port fuel injected (PFI). Ethanol blended fuels, including E85, have a higher octane rating and produce lower exhaust temperatures compared to gasoline. EGR has also been shown to decrease engine knock tendency and decrease exhaust temperatures. A natural progression was to take advantage of the superior combustion characteristics of E85 (i.e. increase compression ratio), and then employ EGR to maintain performance with gasoline. When EGR alone could not provide the necessary knock margin, hydrogen (H2) was added to simulate an onboard fuel reformer.

A dynamometer test methodology was developed for evaluation of HMMWV axle efficiency with hypoid gearsets, comparing those having various degrees of superfinish versus new production axles as well as used axles removed at depot maintenance. To ensure real-world applicability, a HMMWV variant vehicle model was created and simulated over a peacetime vehicle duty cycle, which was developed to represent a mission scenario. In addition, tractive effort calculations were then used to determine the maximum input torques. The drive cycle developed above was modified into two different profiles having varying degrees of torque variability to determine if the degree of variability would have a significant influence on efficiency in the transient dynamometer tests. Additionally, steady state efficiency performance is measured at four input pinion speeds from 700-2500 rpm, five input torques from 50 - 400 N⋅m, and two sump temperatures, 80°C and 110°C.

A Dodge Omni electric car was prepared for competition in an electric “stock car” 2-hour endurance event: the inaugural Solar and Electric 500 Race, April 7, 1991. This entry utilized a series-wound, direct-current 21-hp electric motor controlled by an SCR frequency and pulse width modulator. Two types of lead-acid batteries were evaluated and the final configuration was a set of 16 (6-volt each) deep-cycle units. Preparation involved weight and friction reduction; suspension modification; load, charge and temperature instrumentaltion; and electrical interlock and collision safety systems. Vehicle testing totalled 15 hours of operation. Ranges observed in testing with the final configuration were from 30 to 52 miles for loads of 175 to 90 amperes. These were nearly constant, continuous discharge cycles. The track qualifying speed (64mph) was near the 68 mph record set by the DEMI Honda at the event on the one-mile track.

Connected and automated driving technology is known to improve real-world vehicle efficiency by considering information about the vehicle’s environment such as traffic conditions, traffic lights or road grade. This study shows how the powertrain of a hybrid-electric vehicle realizes those efficiency benefits by developing methods to directly measure real-time transient power losses of the vehicle’s powertrain components through chassis-dynamometer testing. This study is a follow-on to SAE Technical Paper 2019-01-0116, Test Methodology to Quantify and Analyze Energy Consumption of Connected and Automated Vehicles [1], to understand the sources of efficiency gains resulting from connected and automated vehicle driving. A 2017 Toyota Prius Prime was instrumented to collect power measurements throughout its powertrain and driven over a specific driving schedule on a chassis dynamometer.

The US Army is currently seeking to reduce fuel consumption by utilizing fuel efficient lubricants in its ground vehicle fleet. An additional desire is for a lubricant which would consist of an all-season (arctic to desert), fuel efficient, multifunctional Single Common Powertrain Lubricant (SCPL) with extended drain capabilities. To quantify the fuel efficiency impact of a SCPL type fluid in the engine and transmission, current MIL-PRF-46167D arctic engine oil was used in place of MIL-PRF-2104G 15W-40 oil and SAE J1321 Fuel Consumption In-Service testing was conducted. Additionally, synthetic SAE 75W-140 gear oil was evaluated in the axles of the vehicles in place of an SAE J2360 80W-90 oil. The test vehicles used for the study were three M1083A1 5-Ton Cargo vehicles from the Family of Medium Tactical Vehicles (FMTV).

The design and selection of a hydraulic system for a particular machine is based upon a variety of factors which include: functionality, performance, safety, cost, reliability, duty cycle, component availability, and efficiency. With higher fuel costs and requirements to reduce engine exhaust emissions, new hydraulic system configurations should be considered. Traditional hydraulic systems conssume an excessive amount of energy due to metering losses. A single pump usually supplies flow to multiple functions, with differing flow and pressure requirements resulting in excessive metering losses. The energy of mass and inertial loads is usually dissipated by metering losses. Opportunities exist for reducing metering losses by the use of multiple pumps and by using hydrostatic control of individual functions. Hydrostatic control also allows for energy recovery when used in conjunction with an energy storage system.

The short-term future direction of the automotive transportation sector is uncertain. Many governments and environmental localities around the world are proposing internal combustion engine (ICE) bans and enacting large subsidy programs for zero-tailpipe emissions vehicles powered by batteries or fuel-cells. Such policies can be effective in driving the consumer towards specific powertrains. The reason for such aggressive change is to reduce the sector’s carbon footprint. However, it is not clear if these proposals will reduce greenhouse gas (GHG) emissions. Emissions from raw material extraction, manufacturing, and power generation are shadowed by the focus on reducing the reliance on fossil fuel use. Emissions from non-tailpipe sources should also be considered before pushing for a rapid change to powertrains. Life-cycle analysis (LCA) can assess the GHG emissions produced before, during and after the life of a vehicle in a cradle-to-grave analysis.

Fuel costs to operate large trucks have risen substantially in the last few years and, based on petroleum supply/demand curves, that trend is expected to continue for the foreseeable future. Non-propulsion or parasitic loads in a large truck account for a significant percentage of overall engine load, leading to reductions in overall vehicle fuel economy. Electrification of parasitic loads offers a way of minimizing non-propulsion engine loads, using the full motive force of the engine for propulsion and maximizing vehicle fuel economy. This paper covers the integration and testing of electrified accessories, powered by a fuel cell auxiliary power unit (APU) in a Class 8 tractor. It is a continuation of the efforts initially published in SAE paper 2005-01-0016.

Comparative abuse tests were performed on commercially available 12 V and 36 V battery designs. Four methods were chosen from SAE J2464 standard, Electrical Vehicle Battery Abuse Testing, March 1999, and modified to apply them to typical-sized automotive batteries. The four tests included a Penetration Test, Crush Test, Radiant Heat Test, and Short Circuit Test. Both the 12 V and 36 V batteries showed minimal reactions to the tests, and there was no significant difference between results of the two designs with respect to the abuse tests performed. It should be stressed however, that this project was limited in scope and was not intended to be a thorough investigation in the batteries safety hazards.

Conventional methods for determining automotive powertrain efficiency include (1) component-level testing, such as engine dynamometer, transmission stand or axle stand testing, (2) simulations based on component level test data and (3) vehicle-level testing, such as chassis dynamometer or on-road testing. This paper focuses on vehicle-level testing to show where energy is lost throughout a complete vehicle powertrain. This approach captures all physical effects of a vehicle driving in real-world conditions, including torque converter lockup strategies, transmission shifting, engine control strategies and inherent mechanical efficiency of the components. A modern rear-wheel drive light duty pickup truck was instrumented and tested on a chassis dynamometer. Power was measured at the engine crankshaft output, the rear driveshaft and at the dynamometer.

An Automatic Tire Inflation System (ATIS), specifically designed for use on commercial long haul trailers, requires modification of the axles to direct air to the tires. The ATIS requires a drilled hole through the axle tube for the installation of a pneumatic fitting. The trucking industry expressed concern about the modification and its impact upon the axle structure, and the general durability of the system over a long period. A three-phase test program was developed and conducted to satisfy the concerns of the industry.

An Emergency Tire Inflation System (ETIS) designed for use on commercial trucks was evaluated and tested. The ETIS is provided in kit form and designed to be installed by a truck operator to provide emergency air to inflate a low or punctured tire on tractor drive axles. The ETIS will continue to supply air to the tire until the system pressure falls below a safe air pressure level. The system is designed to allow the rig to be driven 500 miles to a tire repair station or to a safe location where tire repair service is available. The installation kit (Figure 1), which can fit under a truck seat, includes all the necessary equipment to install the system on the most common drive axles. The ETIS supplies air to the under-inflated tire through a previously qualified1 Rotary Union design. The Rotary Union is attached to the axle flange of the drive axle by a threaded adapter and two adjustable links that allow the Rotary Union to be placed at the center of rotation of the axle.

An Automatic Tire Inflation System (ATIS), specifically designed for use on commercial long haul trailers underwent complete testing and evaluation in 1993/1994.1 Testing and evaluation included a field test of a prototype system and a controlled laboratory evaluation of the Rotary Union which is the only component subject to wear. The testing of the prototype system indicated that design improvements were necessary before the system could be installed in fleet operations. The design improvements were completed and field installation of production ATIS began. The design improvements were intended to improve overall system durability, decrease installation time, to have less effect on the axle structure than the original design, implement the use of SAE or DOT Approved pressure components and increase overall dependability of the system. ATIS systems have now been developed and tested for most domestic trailer axle configurations.

Over twenty prototype hybrid buses and other commercial vehicles are currently being completed and deployed. These vehicles are primarily “series” hybrid vehicles which use electric motors for primary traction while internal combustion engines, or high-speed turbine engines connected to generators, supply some portion of the electric propulsion and battery recharge energy. Hybrid-electric vehicles have an electric energy storage system on board that influences the operation of the heat engine. The storage system design and level affect the vehicle emissions, electricity consumption, and fuel economy. Existing heavy-duty emissions test procedures require that the engine be tested over a transient cycle before it can be used in vehicles (over 26,000 lbs GVW). This paper describes current test procedures for assessing engine and vehicle emissions, and proposes techniques for evaluating engines used with hybrid-electric vehicle propulsion systems.

An Automatic Tire Inflation System (ATIS) specifically designed for commercial use on trailer axles is currently being installed and utilized successfully by trucking companies, the military and owner/operators throughout the U.S. A need exists for an ATIS specifically designed for the drive axles of Class 8 over-the- road tractors. The addition of an ATIS for drive axles will expand automatic tire monitoring capability to all heavily loaded tires of the over-the-road truck/trailer rig. An ATIS for drive axles has been designed, fabricated and tested. Testing and evaluation of the prototype ATIS drive axle system indicates the system can be successfully installed on a typical tractor rig and operated for an extended period without problems. The testing included a 50,000 mile evaluation of the ATIS installed in a laboratory test fixture. The test fixture used stock axle parts and operated at 65 MPH. Environmental testing was conducted at temperatures ranging from -20 to +200 degrees F.

The State of Florida initiated the SunGuide® Advanced Traffic Management System (ATMS) software development program in October 2003; that software is deployed in over 15 Traffic Management Centers (TMCs) throughout the major cities in Florida. One of SunGuide's biggest strengths is a software architecture that allows for short development times for new functionality. This paper describes the system design, implementation, and lessons learned from the development of the SunGuide Connected Vehicle Subsystem (CVS). The SunGuide CVS receives real-time speed, location, and heading data from instrumented vehicles and uses that data in a manner similar to its use of traffic detector data to provide information to the TMC. In addition to the vehicle providing data to the TMC, the TMC may create and publish Traveler Advisory Messages to the vehicle as part of the SunGuide Event Management response plans.

Several techniques have been developed to measure the relative amount of splash and spray produced by vehicles when driven on wet roads at highway speeds under controlled conditions. This paper discusses considerations in the development of measurement techniques such as those utilizing photographs, a photometer, densitometer, spraymeter, and spray collector. The development of each technique is described. Some test data utilizing the photometer and densitometer techniques are presented in a comparison of two different trucks run on two different road surfaces with new and worn tires, fully loaded and unloaded, and under light and heavy road moisture conditions.

Since the turn of the millennium, automated vehicle technology has matured at an exponential rate, evolving from research largely funded and motivated by military and agricultural needs to a near-production market focused on everyday driving on public roads. Research and development has been conducted by a variety of entities ranging from universities to automotive manufacturers to technology firms demonstrating capabilities in both highway and urban environments. While this technology continues to show promise, corner cases, or situations outside the average driving environment, have emerged highlighting scenarios that impede the realization of full automation anywhere, anytime. This paper will review several of these corner cases and research deficiencies that need to be addressed for automated driving systems to be broadly deployed and trusted.

A detailed component performance, ratings, and cost study was conducted on series and parallel hybrid electric vehicle (HEV) configurations for several battery pack and main electric traction motor voltages while meeting stringent Partnership for a New Generation of Vehicles (PNGV) power delivery requirements. A computer simulation calculated maximum current and voltage for each component as well as power and fuel consumption. These values defined the peak power ratings for each HEV drive system's electric components: batteries, battery cables, boost converter, generator, rectifier, motor, and inverter. To identify a superior configuration or voltage level, life cycle costs were calculated based on the components required to execute simulated drive schedules. These life cycle costs include the initial manufacturing cost of components, fuel cost, and battery replacement cost over the vehicle life.

This paper analyzes the hybridization of a conventionally powered light duty front wheel drive pick up truck by adding an electric motor driven rear axle. Also studied are the effects of using propane fuel instead of gasoline. This hybrid powertrain configuration can be described as a parallel hybrid electric vehicle. Supervisory power management control has been developed to best determine the proportion of load to be provided by the engine and/or electric motor. To perform these analyses, a simulation tool (computer model of the powertrain components) was developed using MATLAB/SIMULINK'. The models account for the thermal and mechanical efficiencies of the components and are designed to develop control strategies for meeting road loads with improved fuel economy and reduced emissions. Results of this study have shown that fuel economy can be improved and emissions reduced using commercially available components (motor, rear axle, and lead acid batteries).