Search Results

The base design of commercial vehicle wheel end systems has changed very little over the past 50 years. Current bearings for R-drive and trailer wheel end systems were designed between the 1920's and the 1960's and designs have essentially remained the same. Over the same period of time, considerable gains have been made in bearing design, manufacturing capabilities and materials science. These gains allow for the opportunity to significantly increase bearing load capacity and improve efficiency. Government emissions regulations and the need for fuel efficiency improvements in truck fleets are driving the opportunity for redesigned wheel end systems. The EPA and NHTSA standard requires up to 23% reduction in emissions and fuel consumption by 2017 relative to the 2010 baseline for heavy-duty tractor combinations.

This paper discusses the change in vehicle parameters when moving from a conventional internal combustion engine (ICE) to an electric motor. In particular, the paper discusses the impact on the wheel end bearings, which must handle higher GAWRs (gross axle weight ratings) at lower center of gravity heights on electric vehicles. These changes require bearings to handle higher loads. Typically, larger loads increase the bearing size and with it, the mounting interface dimensions for auxiliary components. In this paper, The Timken Company demonstrates an alternative bearing design that can handle higher electric vehicle GAWRs but allows for continuity in the surrounding brake corner components - potentially saving OEMs significant design costs and delays. This solution focuses on the mid- and large-size SUV market where bearing capacity could be a limiting factor for electric vehicle variants - driving significant wheel end brake corner design changes to accommodate the larger bearings.

Determination of an engine's inertial properties is critical during vehicle dynamic analysis and the early stages of engine mounting system design. Traditionally, the inertia tensor can be determined by torsional pendulum method with a reasonable precision, while the center of gravity can be determined by placing it in a stable position on three scales with less accuracy. Other common experimental approaches include the use of frequency response functions. The difficulty of this method is to align the directions of the transducers mounted on various positions on the engine. In this paper, an experimental method to estimate an engine's inertia tensor and center of gravity is presented. The method utilizes the traditional torsional pendulum method, but with additional measurement data. With this method, the inertia tensor and center of gravity are estimated in a least squares sense.

Low frequency torsional vibrations can be a significant source of objectionable vehicle vibrations and in-vehicle boom, especially with changes in engine operation required for improved fuel economy. These changes include lower torque converter lock-up speeds and cylinder deactivation. This paper has two objectives: 1) Examine the effect of increased torsional vibrations on vehicle NVH performance and ways to improve this performance early in the program using test and simulation techniques. The important design parameters affecting vehicle NVH performance will be identified, and the trade-offs required to produce an optimized design will be examined. Also, the relationship between torsional vibrations and mount excursions, will be examined. 2) Investigate the ability of simulation techniques to predict and improve torsional vibration NVH performance. Evaluate the accuracy of the analytical models by comparison to test results.

This paper describes the process used to develop an experimental model with forward prediction capabilities for passenger vehicle axle whine performance, focusing initially on beam axle design modifications. This process explains how experimental Transfer Path Analysis (TPA), Running Modes Analysis (RMA) and Modal Analysis were used along with an experimental FRF-Based Substructuring (FBS) model. The objective of FBS techniques is to predict the dynamic behavior of complex structures based on the dynamic properties of each component of the structure. The FBS model was created with two substructures, the body/suspension and the empty rear beam axle housing. Each step in the creation of the baseline FBS model was correlated, and the forward predictive capability was verified utilizing an experimental modification to the beam axle structure.

This paper summarizes a study on axle balance measurement and balancing strategies. Seven types of axles were investigated. Test samples were randomly selected from products. Two significant development questions were set out to be answered: 1) What is the minimum rotational speed possible in order to yield measured imbalance readings which correlated to in-vehicle imbalance-related vibration. What is the relationship between the measured imbalance and rotational speed. To this end, the imbalance level of each axle was measured using a test rig with different speeds from 800 to 4000 rpm with 200 rpm increments. 2) Is it feasible to balance axle sub-assemblies only and still result in a full-assembly that satisfies the assembled axle specification? To this end, the sub-assemblies were balanced on a balance machine to a specified level. Then with these balanced sub-assemblies, the full assemblies were completed and audited on the same balance test rig in the same way.

Brake torque variation is a source of objectionable NVH body/chassis response. Such input commonly results from brake disk thickness variation. The NVH dynamic characteristics of a vehicle can be assessed and quantified through experimental modal testing for determination of mode resonance frequency, damping property, and shape. Standard full vehicle modal testing typically utilizes a random input excitation into the vehicle frame or underbody structure. An alternative methodology was sought to quantify and predict body/chassis sensitivity to brake torque variation. This paper presents a review of experimental modal test methodologies investigated for the reproduction of vehicle response to brake torque variation in a static laboratory environment. Brake caliper adapter random and sine sweep excitation input as well as body sine sweep excitation in tandem with an intentionally locked brake will be detailed.

NVH targets for future vehicles are often defined by utilizing a competitive benchmarking vehicle in conjunction with an existing production and/or reference vehicle. Mode management of full vehicle modes is one of the most effective and significant NVH strategies to achieve such targets. NVH dynamic characteristics of a full vehicle can be assessed and quantified through experimental modal testing for determination of global body mode resonance frequency, damping property, and mode shape. Major body modes identified from full vehicle modal testing are primarily dominated by the vehicle's body-in-white structure. Therefore, an estimate of BIW modes from full vehicle modes becomes essential, when only full vehicle modes from experimental modal testing exist. Establishing BIW targets for future vehicles confines the fundamental NVH behavior of the full vehicle.

This paper describes the application of the modal compliance method to a complex structure such as a vehicle body in white, and the extension of the method from normal modes to the complex modes of a complete vehicle. In addition to the usual bending and torsion calculations, the paper also describes the application of the method to less usual tests such as second torsion, match-boxing and breathing. We also show how the method can be used to investigate the distribution of compliance throughout the structure.

NVH refinement of passenger vehicles is crucial to customer acceptance of contemporary vehicles. This paper describes the vehicle NVH development process, with specific examples from a Diesel sedan application that was derived from gasoline engine-based vehicle architecture. Using an early prototype Diesel vehicle as a starting point, this paper examines the application of a Vehicle Interior Noise Simulation (VINS) technique in the development process. Accordingly, structureborne and airborne noise shares are analyzed in the time-domain under both steady-state and transient test conditions. The results are used to drive countermeasure development to address structureborne and airborne noise refinement. Examples are provided to highlight the refinement process for “Diesel knocking” under idle as well as transient test conditions. Specifically, the application of VINS to understanding the influence of high frequency dynamic stiffness of hydro-mounts on Diesel clatter noise is examined.

Repair and remanufacture has become an accepted method to extend bearing useful life in many applications, including positions within off-highway construction and mining vehicles. However, it has not been an easy task for equipment owners to become confident in the use of repaired bearings, nor has it been an easy task for engineers to select the positions best suited for repair, as robust analytical methods to predict performance are not available. This has lead to many field test campaigns of repaired bearings on different bearing positions until the equipment owners gain enough confidence to make it part of their normal operating procedures. This paper aims to reduce the test and validation cycle that occurs with the use of repaired and remanufactured bearings by developing analytical methods to predict bearing performance. Life prediction algorithms are presented covering the different levels of repair available.

The Frequency Response Function (FRF) is a fundamental component to identifying the dynamic characteristics of a system. FRF's have a significant impact on modal analysis and root cause analysis of NVH issues. In most cases the FRF can be easily measured, but there are instances when the measurement is unobtainable due to spatial constraints. This paper outlines a simple experimental method for obtaining a high quality input-output FRF of a structure in areas where an impact hammer can not reach during impact testing. Traditionally, the FRF in such an area is obtained by using a load cell extender with a hammer impact excitation. A common problem with this device is a double hit, that yields unacceptable results.

The aspects of real engineering surfaces are discussed with regard to their three-dimensional nature. A review of potential uses of surface finish measurement methods is discussed for characterization of functional surfaces. Using an optical-based system and a set of specific measurement procedures, two functional surfaces with different roughness were analyzed to illustrate a typical surface topography evaluation. A simple sliding test was then utilized to show that a special finish produced by a proprietary finishing process can provide improved performance, as measured by wear differences, frictional properties and operating temperature of the system. A special surface treatment was then evaluated in conjunction with the special finish in order to enhance its functional load support. Simple sliding test results indicates a potential new engineered surface for improving tribological contact performance.

A method of manufacturing has been developed to produce externally profiled mechanical seamless tubing for cams, races and similarly shaped parts, rather than machining these profiles from tube blanks or forging them to net-shape from powder metal. The desired profile is produced on the outside diameter of the entire length of a tube by cold drawing. Discrete parts cut from these tubes will have the surface finish, mechanical properties, and dimensional accuracy typical of cold formed products. In addition, relative to the use of tube blanks, material yield is increased since OD machining is eliminated.

During the design process for a vehicle, the CAD surface geometry becomes available at an early stage so that numerical assessment of aerodynamic performance may accompany the design of the vehicle's shape. Accurate prediction requires open grille models with detailed underhood and underbody geometry with a high level of detail on the upper body surface, such as moldings, trim and parting lines. These details are also needed for aeroacoustics simulations to compute wall-pressure fluctuations, and for thermal management simulations to compute underhood cooling, surface temperatures and heat exchanger effectiveness. This paper presents the results of a significant effort to capitalize on the investment required to build a detailed virtual model of a pickup truck in order to simultaneously assess performance factors for aerodynamics, aeroacoustics and thermal management.

The need for efficient space utilization has provided a framework for the design of a 248mm family of torque converters that supports a wide choice of engine and transmission combinations. The axial length of the part and its weight have been substantially reduced while the performance range has been broadened without degradation of efficiency. The new converter operates in an expanded slipping clutch mode. It significantly contributes to the performance and fuel economy improvements of related vehicles. To meet the cost target, the comprehensive lineup and the resulting complexity have required a high level of component interchangeability. During the design phase, the manufacturing core competencies were scrutinized and process redundancies eliminated, both resulting in optimization of material selection and applicable technology.

Tailor welded steel blanks have long been applied in stamping of automotive parts such as door inner, b-pillar, rail, sill inner and liftgate inner, etc. However, there are few known tailor welded aluminum blanks in production. Traditional laser welding equipment simply does not have the capability to weld aluminum since aluminum has much higher reflectivity than steel. Welding quality is another issue since aluminum is highly susceptible to pin holes and undercut which leads to deterioration in formability. In addition, high amount of springback for aluminum panels can result in dimension control problem during assembly. A tailor-welded aluminum blank can help reducing dimension variability by reducing the need for assembly. In this paper, application of friction stir and plasma arc welded blanks on a liftgate inner will be discussed.

In automotive testing, a chassis dynamometer is typically used, during cell testing, to evaluate vehicle performance by simulating actual driving conditions. The use of indoor cell testing has the advantage of running controlled tests where the cell temperature and humidity and solar loads can be well controlled. Driving conditions such as vehicle speed, wind speed and grade can be also controlled. Thus, repeated tests can be conducted with minimum test variations. The tractive effort required at the wheels of a vehicle for a given set of operating parameters is determined by taking into account a set of variables which affect vehicle performance. The forces considered in determination of the tractive effort include the constant friction force, variable friction force due to mechanical and tire friction, forces due to inertia and forces due to aerodynamic and wind effects. In addition, forces due to gravity are considered when road grades are simulated.

This paper identifies the difference in powertrain cooling system content levels using a nominal and a +3 Standard deviation maximum temperature design approach. Variation simulation analysis tools are used along with a 1-D cooling system performance model to predict resulting temperature distribution for different combinations of input variable populations. The analysis will show differential in powertrain cooling system content, mass, and impact to fuel economy for a nominal vs. +3 sigma design approach.

Brake judder, which is a low frequency excitation of the suspension and thus, the body structure during low-G braking, is mainly felt at the steering wheel and throughout the vehicle structure. Brake judder is a problem that costs manufacturers millions of dollars in warranty cost and undesirable trade offs. The magnitude of judder response depends not only on the brake torque variation, but also on the suspension design character-istics. This paper discusses the judder simulation process using ADAMS software to investigate the suspension design sensitivity to the first order brake judder performance. The paper recommends “tuning knobs” to suspension designers and vehicle development engineers to resolve issues in the design and development stages. Various suspension design varia-bles including geometry and compliances as well as brake related characteristics were investigated.