Search Results

The HELP Program and Crescent Demonstration Project is a bi-national multi-jurisdictional cooperative research and demonstration project involving the public and private sectors in an application of advancing technologies in the creation of an integrated heavy vehicle management system with applications to both highway and vehicle systems. This initiative is a leading example of the Intelligent Vehicle Highway Systems (IVHS) in commercial vehicle operations (CVO). The selected technologies are being integrated into a heavy vehicle management system. These technologies include: (1) automatic vehicle identification (AVI), (2) weigh-in-motion (WIM), (3) automatic vehicle classification (AVC), (4) data communication networks and systems integration. The program, initiated approximately eight years ago, consists of three phases which include assessing the feasibility of the concept, technical studies involving laboratory and field tests, and, lastly, the demonstration phase.

An important component in many hybrid electric vehicle (HEV) concepts is the load leveling device (LLD). The best type of LLD for HEVs is under debate. This paper identifies the important concept selection criteria for the three leading types of LLDs being considered for use in HEVs. The performance of electrochemical batteries, ultracapacitors, and flywheels is compared using these criteria. The concept selection methodology indicates that at the present time flywheels show the most promise for development for use in a hybrid electric vehicle. The use of this type of selection methodology is a powerful tool in identifying concepts worthy of development as well as determining performance criteria in need of improvement within each concept.

Trucks operating in inter-modal (drayage) operation in and around port and rail terminals, are responsible for a large proportion of the emissions of NOX, which are problematic for the air quality of the Houston and Dallas/Ft. Worth metro areas. A standard test cycle, called the Texas Dray Truck Cycle, was developed to represent the operation of heavy-duty diesel trucks in dray operations. The test cycle reflects the substantial time spent at idle (~45%) and the high intensity of the on-road portions. This test cycle was then used in the SAE J1321 test protocol to evaluate the effect on fuel consumption and NOX emissions of retrofitting dray trucks with light-weight, low-rolling resistance wide-single tires. In on-track testing, a reduction in fuel consumption of 8.7% was seen, and NOX emissions were reduced by 3.8% with the wide single tires compared to the conventional tires.

The University of Texas 2000 Ethanol Vehicle Challenge team remains focused on cold start, cold drivability, fuel economy, and emissions reduction for our 2000 Ethanol Vehicle Challenge entry. We used the stock PCM for all control functions except control of an innovative cold-start system our team designed. The primary modifications for improved emissions control involved ceramic coating of the exhaust manifolds, use of close-coupled ethanol-specific catalysts, use of a moddified version of the California Emissions Calibrated PCM, and our cold-start system that eliminates the need to overfuel the engine at the beginning of the FTP. Additionally, we eliminated EGR at high load to improve power density. Major modifications, such as increasing the compression ratio or pressure boosting, were eliminated from consideration due to cost, complexity, reliability, or emissions penalties.

This paper presents the results of original research conducted to evaluate the braking characteristics of passenger vehicles equipped with anti-lock braking systems (ABS) as a function of brake-pedal application force. The conditions studied in this paper are for braking on a dry, level roadway without any steering input. The objective of the paper is to study the effect of brake-pedal application force on the braking systems of common vehicles currently in-use. Comparisons are made between ABS and locked-wheel braking for each vehicle. The subject of this paper is part of the general topic of passenger vehicle dynamics and stability. Knowledge of how a vehicle performs under a variety of braking conditions is important for a variety of applications such as 1) intelligent vehicle highway systems, 2) vehicle stability and control, 3) vehicle dynamics, and 4) accident reconstruction.

This paper presents the results of original research conducted to evaluate the braking characteristics of passenger vehicles equipped with anti-lock braking systems (ABS) as a function of vehicle speed at the beginning of a braking maneuver. The conditions studied in this paper are for braking on a dry, level roadway without any steering input. The objective of the paper is to study the effect of vehicle speed on the braking systems of common vehicles currently in-use. Comparisons are made between ABS and locked-wheel braking for each vehicle. The subject of this paper is part of the general topic of passenger vehicle dynamics and stability. Knowledge of how a vehicle performs under a variety of braking conditions is important for a variety of applications such as 1) intelligent vehicle highway systems, 2) vehicle stability and control, 3) vehicle dynamics, and 4) accident reconstruction.

The results of continuing investigations of a new type of ignitor, the railplug, are reported. Previous studies have shown that railplugs can produce a high velocity jet of plasma. Additionally, railplugs have the potential of assuring ignition under adverse conditions, such as cold start of an IDI diesel engine, because the railplug plasma can force ignition in the combustion chamber rather than relying on autoignition under cold start conditions. In this paper, engine data are presented to demonstrate the improved cold starting capability obtainable with railplugs. Data acquired using a railplug are compared to results obtained using no assist and using glow plugs. The engine used for this investigation will not start without glow plugs (or some starting aid) at temperatures below O°C, and the manufacturer's specification of the cold start limit for this engine using glow plugs is -24°C. Railplugs are able to initiate combustion at -29°C in one to two seconds with no preheating.

The technology thrust to develop an effective electromagnetic actuator for application in an active suspension system has precipitated a fresh look at the active control schemes in an effort to reduce the required force levels of the actuator. The resulting “near constant force” control algorithm is described and its ability to greatly reduce vehicle sprung mass motion is documented through simulation and single wheel station laboratory test stand results. The vehicle power and energy requirements associated with this unwanted vehicle vertical are analyzed and comparisons between the corresponding passive and active systems are presented. The success of the active system leads naturally to the conclusion that a passive suspension equipped vehicle will become power limited at a much lower speed than will this active system when traversing severe cross-country terrain.

The On-Board Distillation System (OBDS) extracts, from gasoline, a highly volatile crank fuel that enables simultaneous reduction of start-up fuel enrichment and significant ignition timing retard during cold-starting. In a previous paper we reported reductions in catalyst light-off time of >50% and THC emissions reductions >50% over Phase I of the FTP drive cycle. The research presented herein is a further development of the OBDS concept. For this work, OBDS was improved to yield higher-quality start-up fuel. The PCM calibration was changed as well, in order to improve the response to intake manifold pressure transients. The test vehicle was tested over the 3-phase FTP, with exhaust gases speciated to determine NMOG and exhaust toxics emissions. Also, the effectiveness of OBDS at generating a suitable starting fuel from a high driveability index test gasoline was evaluated.

The University of Texas at Austin Center for Electromechanics (UT-CEM) has designed and tested a flywheel energy storage system conventionally referred to as a flywheel battery (FWB) for power averaging on a hybrid electric transit bus. The system incorporates a high speed (40,000 rpm) 150 kW permanent magnet motor generator with magnetic bearings to levitate a 2 kWh composite flywheel. This paper summarizes: design goals, required operating parameters, system design, analysis completed prior to fabrication, and initial performance testing completed in the laboratory. The paper includes information on the motor/generator, power electronics, magnetic bearing sensors and controls, and FWB subsystems (including containment). Finally, recommendations for continued testing are made along with recommendations for improvements to the existing design.

The University of Texas Ethanol Vehicle Challenge team focused upon cold start/driveability, fuel economy, and emissions reduction for our 1999 Ethanol Vehicle Challenge entry. We replaced or coated all fuel system components that were not ethanol compatible. We used the stock PCM for all control functions except control of a novel cold-start system our team designed. The primary modifications for improved emissions control involved ceramic coating of the exhaust manifolds, use of close-coupled ethanol-specific catalysts, increased EGR for the operating conditions of the five longest cruises on the FTP, and our cold-start system that eliminates the need to overfuel the engine at the beginning of the FTP. This EGR control scheme should also benefit urban fuel economy. Additionally, we eliminated EGR at high load to improve power density.

This paper presents the results of original research conducted to evaluate the braking characteristics of passenger vehicles equipped with anti-lock braking systems (ABS) as a function of tire inflation pressure. The conditions studied in this paper are for braking on a dry, level roadway without any steering input. The objective of the paper is to study the effect of tire inflation pressure on the braking systems of common vehicles currently in-use. Comparisons are made between ABS and locked-wheel braking for each vehicle. The subject of this paper is part of the general topic of passenger vehicle dynamics and stability. Knowledge of how a vehicle performs under a variety of braking conditions is important for a variety of applications such as 1) intelligent vehicle highway systems, 2) vehicle stability and control, 3) vehicle dynamics, and 4) accident reconstruction.

The cold start process is critical to control the emissions in a gasoline direct injection (GDI) engine. However, the optimization is very challenging due to the transient behavior of the engine cold start. A series of engine simulations using CONVERGE CFD™ were carried out to show the detailed process in the very first firing event of a cold start. The engine operating parameters used in the simulations, such as the transient engine speed and the fuel rail pressure (FRP), came from companion experiments. The cylinder pressure traces from the simulations were compared with experiments to help validate the simulation model. The effects of variation of the transient parameters on in-cylinder mixture distribution and combustion are presented, including the effects of the rapidly changing engine speed, the slowly vaporized fuel due to the cold walls, and the low FRP during the first firing cycle of a 4-cylinder engine. Comparison was also made with non-transient steady state operation.