Criteria

Text:
Sector:
Affiliation:
Display:

Results

Viewing 1 to 30 of 192
2011-04-12
Technical Paper
2011-01-0620
Di Yao, Diming Lou, Zhiyuan Hu, Piqiang Tan
An EURO 3 certified common rail diesel engine was fueled with pure petroleum diesel (EURO 4 standard) and three different alternative blended diesel fuels, 10% biodiesel blended diesel (B10), 10% gas to liquid blended diesel (G10) and 10% water emulsified diesel (E10). Tests were performed at different engine speeds and load states. Particle number concentration and size distribution data were obtained from an engine exhaust particle sizer (EEPS). Over all the working conditions, total particle and nucleation mode particle number concentration among these fuels from high to low were in this order: B10, E10, pure diesel and G10. Proportions for nucleation mode particle over all the operating states in that order were 89%, 82%, 59% and 66%. Particle size distributions of B10 and E10 presented bimodal logarithmic distributions with outstanding nucleation mode peaks at all working conditions.
2013-09-08
Technical Paper
2013-24-0073
Ke Song, Tong Zhang
Most of the existing energy management strategies for Extended-Range Electric Vehicles (E-REVs) are heuristic, which restricts coordination between the battery and the Range Extender. This paper presents an instantaneous optimization energy management strategy based on the Minimum Loss Power Algorithm (MLPA) for a fuel cell E-REV. An instantaneous loss power function of power train system is constructed by considering the charge and discharge efficiency of the battery, together with the working efficiency of the fuel cell Range Extender. The battery working mode and operating points of the fuel cell Range Extender are decided by an instantaneous optimization module (an artificial neural network) that aims to minimize the loss power function at each time step.
2011-04-12
Journal Article
2011-01-1057
Junying Min PhD, Jianping Lin
Hot forming process of ultrahigh strength boron steel 22MnB5 is widely applied in vehicle industry. It is one of the most effective approaches for vehicle light weighting. Dynamic recovery is the major softening mechanism of the boron steel under austenite state at elevated temperatures. Deformation mechanism of the boron steel can be revealed by investigation on the behavior of dynamic recovery, which could also improve the accuracy of forming simulations for hot stamping. Uniaxial tensile experiments of the boron steel are carried out on the thermo-mechanical simulator Gleeble3800 at elevated temperatures. The true stress-strain curves and the relations between the work hardening rate and flow stress are obtained in different deformation conditions. The work hardening rate decreases linearly with increasing the flow stress.
2013-03-25
Technical Paper
2013-01-0088
Chengyi Li, Shuguang Zuo
To wheel driven electric vehicle, besides road unevenness excitation, the electric motor torque fluctuation has great effects on the whole body vibration (WBV) according to prior research.[1],[2] To evaluate and further reduce the influence of torque fluctuation on the whole body vibration (WBV), vibration characteristic of rear suspension is analyzed thoroughly and finally optimized in this paper. Firstly, based on an existing eccentrical motor driven electric vehicle, a rear twist beam suspension suitable for high frequency analysis is modeled in Adams/View. Secondly, the vibration characteristic is simulated using Adams/Vibration module and verified with natural modal parameters of system. Finally, the vibration characteristic is optimized by adjusting the parameters of bushings using DOE method and proven to be effective to reduce WBV caused by torque fluctuation.
2016-04-05
Technical Paper
2016-01-1451
Mingyang Chen, Xichan Zhu, Zhixiong Ma, Lin Li
Abstract In China there are many mixed driving roads which cause a lot of safety problems between vehicles and pedalcyclists. Research on driver behavior under risk scenarios with pedalcyclist is relatively few. In this paper driver brake parameters under naturalistic driving are studied and pedalcyclists include bicyclist, tricyclist, electric bicyclist and motorcyclist. Brake reaction time and maximum brake jerk are used to evaluate driver brake reaction speed. Average deceleration is used to evaluate the effect of driver brake operation. Maximum deceleration is used to evaluate driver braking ability. Driver behaviors collected in China are classified and risk scenarios with pedalcyclist are obtained. Driver brake parameters are extracted and statistical characteristics of driver brake parameters are obtained. Influence factors are analyzed with univariate ANOVA and regression analysis.
2016-04-05
Technical Paper
2016-01-1535
Linli Tian, Yunkai Gao
Abstract Based on equivalent static loads method (ESL), a nonlinear dynamic topology optimization is carried out to optimize an automotive body in white (BIW) subjected to representative legislative crash loads, including frontal impact, side barrier impact, roof crush and rear impact. To meet the crashworthiness performances, two evaluation indexes are defined to convert the practical engineering problems into mathematic optimization problems. The strain energy is treated as the stiffness evaluation index of the BIW and the relative displacement is employed as the compliance index of the components and parts.
2015-04-14
Technical Paper
2015-01-1068
Rong Yang, Diming Lou, Piqiang Tan, Zhiyuan Hu, Hongjuan Ren
Abstract Previous studies have indicated that longer torque increase time benefits the reduction of emissions during transient process for a diesel engine. However, quantitative conclusions on reduction of emissions and effects on fuel economy have not been made clear so far. The aim of this study was to evaluate the transient process of diesel engine under different torque increase time, and to find the quantitative statement between torque increase time, fuel economy and engine-out emissions. To do this, experiment was carried out on a 7L common rail diesel engine used for commercial vehicles. Three engine speeds (1100r·min−1, 1300r·min−1 and 1500r·min−1) were chosen to represent an engine working range. For each speed, the engine torque is increased within different time (0.5s, 1s, 2s and 5s). It was shown that, in the transient process mentioned above, engine torque increase time effects fuel economy, smoke opacity and CO emission.
2015-04-14
Technical Paper
2015-01-1117
Yang Liu, Zechang Sun
Abstract Regenerative braking control for a four-wheel-drive (4WD) electric vehicle (EV) equipped with a decoupled electro-hydraulic brake system was studied. The energy flow of the 4WD electric vehicle was analyzed during braking, and the brake force distribution strategy between the front-rear axles, regenerative braking and hydraulic braking was studied. Considering ECE R13 regulations, motors and battery pack characteristic constraints, the optimal regenerative braking control strategy using Genetic Algorithm (GA) was proposed. A Hardware-in-loop (HIL) test was built to verify the proposed regenerative braking control strategy. The results show that the optimal regenerative braking control strategy for the 4WD electric vehicle was advantageous over the comparison program, and regenerative energy efficiency reaches 78.87% under the Shanghai Urban Driving Cycle (SUDC).
2015-04-14
Journal Article
2015-01-1599
Bo Leng, Lu Xiong, Chi Jin, Jun Liu, Zhuoping Yu
Abstract For an electric vehicle driven by four in-wheel motors, the torque of each wheel can be controlled precisely and independently. A closed-loop control method of differential drive assisted steering (DDAS) has been proposed to improve vehicle steering properties based on those advantages. With consideration of acceleration requirement, a three dimensional characteristic curve that indicates the relation between torque and angle of the steering wheel at different vehicle speeds was designed as a basis of the control system. In order to deal with the saturation of motor's output torque under certain conditions, an anti-windup PI control algorithm was designed. Simulations and vehicle tests, including pivot steering test, lemniscate test and central steering test were carried out to verify the performance of the DDAS in steering portability and road feeling.
2015-04-14
Technical Paper
2015-01-1600
Tong Zou, Lu Xiong, Pengfei Yang, Chi Jin
Abstract Distributed drive electric vehicle (EV) is driven by four independent hub motors mounted directly in wheels and retains traditional hydraulic brake system. So it can quickly produce driving/braking motor torque and large stable hydraulic braking force. In this paper a new control allocation strategy for distributed drive electric vehicle is proposed to improve vehicle's lateral stability performance. It exploits the quick response of motor torque and controllable hydraulic pressure of the hydraulic brake system. The allocation strategy consists of two sections. The first section uses an optimal allocation controller to calculate the total longitudinal force of each wheel. In the controller, a dynamic efficiency matrix is designed via local linearization to improve lateral stability control performance, as it considers the influence of tire coupling characteristics over yaw moment control in extreme situations.
2015-04-14
Technical Paper
2015-01-1729
Chenle Sun, Zhe Wang, Zhaolei Yin, Tong Zhang
Abstract The linear internal combustion engine-linear generator integrated system (LICELGIS) is a generating unit with high power density, high efficiency and low emission for the range-extended electric vehicle. The LICELGIS starts with the linear generator, which shows the advantages of speed, efficiency and emission reduction, as well as the prerequisite to guarantee the steady operation of the system. This paper focuses on the reversing control method and the energy utilization efficiency in the starting process of the LICELGIS. Pursuant to the starting requirements of the linear internal combustion engine, the fewest driving cycle and the evaluation index are obtained. Meanwhile, the velocity tracking mode and the position tracking mode is proposed for the control of the starting force reversing. The motions of the starting process under two control method are comparatively analyzed, indicating that the former has a high efficiency, while the latter is more likely to achieve.
2015-04-14
Technical Paper
2015-01-0747
Aimin Du, Zhongpan Zhu, Chuanchuan Chu, Mengmeng Li
Abstract The improvement of environmental performance by gasoline direct injection (GDI) engine is remarkable. But the gas mixture formation process, which greatly affects the combustion of direct injection spark ignition (DISI) engines, still has a lot of areas left unclear. In this paper, a CFD model of air intake, fuel spray atomization and mixture formation process of a certain GDI engine was developed and experimentally verified for DISI injection study. The effects of injector spray layout and injection strategy on mixture quality of DISI engine were analyzed by respective simulation of three different injectors T1470, T1471, T1472. Results show that the mixture quality can be improved with appropriate injector spray orifices layout.
2015-04-14
Technical Paper
2015-01-0661
Jianwang Shao, Xian Wu, Na Wei, Ding Wang, Guoming Deng, Ming Xu
Abstract An increasing demand for vehicle noise control has been proposed and at the same time, vehicle weight and fuel economy have become critical for the automotive industry. The methodology of statistical energy analysis (SEA) is used to balance both light weight and high noise insulation performance. In this paper, the vehicle dash and floor sound package systems, which are two of the major paths for vehicle interior noise, are studied and optimized by CAE and testing technology. Two types of sound packages which are the conventional insulation system and the lightweight one are chosen for the vehicle dash and floor system. The vehicle dash and floor systems are modeled by SEA and the transmission loss (TL) of the dash and floor system is analyzed, respectively. Several influence factors of the TL are also analyzed, such as sound package coverage, the leaks, etc.
2015-04-14
Journal Article
2015-01-0254
Chunjing Lin, Sichuan Xu, Zhao Li, Guofeng Chang
Abstract A passive thermal management system (TMS) using composite phase change material (PCM) for large-capacity, rectangular lithium-ion batteries is designed. A battery module consisting of six Li-ion cells connected in series was investigated as a basic unit. The passive TMS for the module has three configurations according to the contact area between cells and the composite PCM, i.e., surrounding, front-contacted and side-contacted schemes. Firstly, heat generation rate of the battery cell was calculated using the Bernardi equation based on experimentally measured heat source terms (i.e. the internal resistance and the entropy coefficient). Physical and thermal properties such as density, phase change temperature, latent heat and thermal conductivity of the composite PCM were also obtained by experimental methods. Thereafter, thermal response of the battery modules with the three TMS configurations was simulated using 3D finite element analysis (FEA) modeling in ANSYS Fluent.
2015-03-10
Technical Paper
2015-01-0040
Rong Guo, Chong Cao, Yi Mi
Abstract In course of the electrification of vehicle's powertrain, one of the vital problems we've been faced with is the limitation of the vehicle's driving range due to the capacity of currently available batteries. Therefore, range-extended electric vehicle (ReEV) concept has become one of the most promising transitory technologies to compensate this defect. Electric vehicle is supposed to be quiet and comfortable for the customers. However, some annoying sound derived from powertrain and accessories must be reduced or eliminated to meet this requirement. Accessory NVH has an important contribution to ReEV's NVH performance. If it is not well handled, poor vibration and noise may appear. This paper focuses on accessories' NVH performance in ReEV including the NVH problems from steering pump, vacuum pump and AC compressor.
2016-04-05
Technical Paper
2016-01-0286
Changsheng Wang, Haijiang Liu, Tao Zhang, Zhiyong Zhu, Liang Liu
Abstract With the increasing development in automotive industry, finite element (FE) analysis with model bias prediction has been used more and more widely in the fields of chassis design, body weight reduction optimization and some components development, which reduced the development cycles and enhanced analysis accuracy significantly. However, in the simulation process of plastic fuel tank system, there is few study of model validation or verification, which results that non-risky design decisions cannot be enhanced due to too much consuming time. In this study, to correct the discrepancy and uncertainty of the simulated finite element model, Bayesian inference-based method is employed, to quantify model uncertainty and evaluate the simulated results based on collected data from real mechanical tests of plastic fuel tanks and FE simulations under the same boundary conditions.
2016-04-05
Technical Paper
2016-01-0415
Sijin Wu, Xinya Gao, Yong Lv, Yanpeng Jiang, Yao Fang, Aiguo Zhou
Abstract Temporal phase-shifting and spatial-carrier techniques are the two dominant phase extraction methods used in digital speckle pattern interferometry (DSPI). Temporal phase-shifting technique enjoys the advantages of precise phase extraction and capability of high-quality phase map formation, but suffers from the limitation in its use in dynamic measurement due to the time cost for carrying out the phase shift. To meet the rising demand of dynamic measurement of deformations in modern industry, spatial-carrier technique is developed to extract the phase information from a single speckle interferogram, yielding less time cost during a test. In this paper, both temporal phase-shifting and spatial-carrier techniques are investigated in theory as well as experiment. The experiment results from measuring a same deformation behavior using both techniques are used to compare the performances of the two phase extraction techniques.
2016-04-05
Technical Paper
2016-01-0431
Guangqiang Wu, Huwei Wu, Xiang Chen
Abstract The nonlinear characteristics impact of multi-staged stiffness clutch damper on the vehicle creeping is investigated by using the lumped-parameter modeling method as a certain mass-production passenger sedan is taken as the research subject. Firstly, a quasi-transient engine model of an inline four-cylinder and four-stroke engine, based on measured data of cylinder gas pressure versus crankshaft angle, is derived. Effective output torque is acquired and as the input excitation to the driveline system. Secondly, a 12-DOF (Degree of Freedom) nonlinear and branched powertrain system and vehicle longitudinal dynamics model is established. The differential mechanism characteristics and dynamic tire property based on the LuGre tire model are considered. Then, for a traditional two-staged stiffness clutch damper in consideration of hysteresis characteristics, vehicle powertrain system responses in both the time and frequency domain are obtained.
2016-04-05
Technical Paper
2016-01-0120
Libo Huang, Huanlei Chen, Zhuoping Yu, Jie Bai
Abstract Automotive radar is the most important component in the autonomous driving system, which detects the obstacles, vehicles and pedestrians around with acceptable cost. The target tracking is one of the key functions in the automotive radar which estimates the position and speed of the targets having regarding to the measurement inaccuracy and interferences. Modern automotive radar requires a multi-target tracking algorithm, as in the radar field of view hundreds of targets can present. In practice, the automotive radar faces very complicated and fast-changing road conditions, for example tunnels and curved roads. The targets’ unpredictable movements and the reflections of the electromagnetic wave from the tunnel walls and the roads will make the multi-target tracking a difficult task. Such situation may last several seconds so that the continuous tracks of the targets cannot be maintained and the tracks are dropped mistakenly.
2016-04-05
Journal Article
2016-01-0363
HaiYan Yu, ZeZhen He, JiaYi Shen
Abstract The work-hardening response of TRIP780 steel subjected to strain-path changes was investigated using two-stage tension experiments. Large specimens were prestrained and then sub-sized samples were subjected to tension along various directions. The influence of strain-path changes on flow stress and work hardening performance was discussed in detail. The specific plastic work was calculated to compare the kinematic hardening behaviour after strain-path changes. The results showed that transient hardening was observed for TRIP780 sheets subjected to orthogonal strain-path change. The strain-hardening exponent (n-value) was influenced by prestraining levels and the strain path. The n-value exhibited a greater decrease under an orthogonal strain-path change. Prestraining can delay the onset of high work hardenability of TRIP steels. It is meaningful for the safety design of vehicles.
2016-04-05
Technical Paper
2016-01-0511
Na Qiu, Yunkai Gao, Jianguang Fang, Shanshan Wang
Abstract As a potential material for lightweight vehicle, polymethyl methacrylate (PMMA) has proven to perform well in optical behavior and weather resistance. However, the application in automotive glazing has seldom been studied. This paper investigates the defrost performance of PMMA rear window using both numerical and experimental methods. The finite element analysis (FEA) results were found to be in good agreement with the experimental data. Based on the validated finite element model, we further optimized the defrost efficiency by changing the arrangement of heating lines. The results demonstrated the frost layer on the vision-related region of PMMA rear window can melt within 30 minutes, which meets the requirement of defrost efficiency.
2016-04-05
Technical Paper
2016-01-1094
Fang Liao, Weimin Gao, Yan Gu, Fei Kang, Yinan Li, Cheng Wang
Abstract Generally, the gear rattle noise prediction models are composed of the mass and stiffness elements. The proposals are about the gear inertia or backlash and the shaft inertia or stiffness, but there are many detailed designs in the same inertia, stiffness or backlash conditions. Therefore, these proposals can’t guide detailed designs. These models only investigate the rattle in the rotating degree, and ignore rattle contribution in the radical and axial directions. Those prediction models only consider one or several factors which affect the rattle noise performance. It is difficult to predict the influence of individual factor and multi-factors coupling on the gear rattle noise in a rattle simulation model.
2016-04-05
Technical Paper
2016-01-1186
Dong Hao, Yongping Hou, Jianping Shen, Liying Ma
Abstract The vehicular fuel cell stack is unavoidably impacted by the vibration in the real-world usage due to the road unevenness. However, effects of vibration on stacks have yet to be completely understood. In this work, the mechanical integrity and gas-tightness of the stack were investigated through a strengthen road vibration test with a duration of 200 h. The excitation signals applied in the vibration test were simulated by the acceleration of the stack, which were previously measured in a vehicle vibration test. The load signals of the vehicle vibration test were iterated through a road simulator from vehicle acceleration signals which were originally sampled in the proving ground. Frequency sweep test was conducted before and after the vibration test. During the vibration test, mechanical structure inspection and pressure maintaining test of the stack were conducted at regular intervals.
2016-06-17
Journal Article
2016-01-9144
Pengfei Zang, Zhe Wang, Chenle Sun
Abstract The linear internal combustion engine-linear generator integrated system (LICELGIS) is an innovative structure as a range-extender for the hybrid vehicles, which contains two opposed free piston engines and one linear generator between them. The LICELGIS is a promising power package due to its high power density and multi-fuel flexibility. In the combustion process of linear engines, the top dead center (TDC) position is not stable in different cycles, which significantly affects system operations. Otherwise, pistons move away from the TDC with high-speed because of the tremendous explosive force, which incurs the short residence time of pistons around the TDC and rapid decrease of in-cylinder temperature, pressure and the combustion efficiency. In order to address this problem, a scientific simulation model which includes dynamic and thermodynamic models, is established and a combustion optimization control strategy is proposed.
2017-03-28
Technical Paper
2017-01-0446
Xiao Chuan Xu, Xiuyong Shi, Jimin Ni, Jiaqi Li, Xiaochuan Xu Sr.
Abstract Oil pump is a critical part of engine lubrication system. The performance and efficiency of oil pump are greatly affected by vibration and noise, which would lead to the pump service life decreasing and pump body easily wearing. Hence the vibration and noise of oil pump is of great importance to study. In this paper, a FEA model of the variable displacement oil pump(VDOP) was established to carry on the modal and noise analysis, while the geometric structure was optimized with test verification. The modal analysis of VDOP was carried out by ABAQUS software, the 3-D unsteady flow field in VDOP was simulated by Pumplinx software, and the sound field was analyzed by ACTRAN acoustic module. Using a special oil pump test bench combined with B&K PULSE vibration and noise test equipment, the NVH and comprehensive performance experiment of the VDOP were carried out here.
2017-03-28
Technical Paper
2017-01-0407
Fei Huo, Huyao Wu
Abstract Biomechanics and biodynamics are increasingly focused on the automotive industry to provide comfortable driving environment, reduce driver fatigue, and improve passenger safety. Man-centered conception is a growing emphasis on the open design of automobile. During the long-term driving, occupational drivers are easily exposed to the neck pain, so it is important to reduce the muscle force load and its fatigue, which are not usually considered quantitatively during traditional ergonomics design, so standards related are not well developed to guide the vehicle design; On the other hand, the head-neck models are always built based on the statics theory, these are not sufficient to predict the instantaneous variation of the muscle force. In this paper, a head-neck model with multi DOFs is created based on multibody dynamics. Firstly, a driver-vehicle-road model considering driver multi-rigid body model, vehicle subsystems, and different ranks of pavement is built.
2017-03-28
Technical Paper
2017-01-0417
Yingjun Li, Yunkai Gao, Gangan Ma, Qianqian Du, Yabin Wan
Abstract To solve the problem of serious roller wear and improve the smoothness of the sliding door motion process, the rigid-flexible coupling multi-body model of the vehicle sliding door was built in ADAMS. Force boundary conditions of the model were determined to meet the speed requirement of monitoring point and time requirement of door opening-closing process according to the bench test specification. The results of dynamic simulation agreed well with that of test so the practicability and credibility of the model was verified. In the optimization of the ride comfort of the sliding door, two different schemes were proposed. The one was to optimize the position of hinge pivots and the other was to optimize the structural parameters of the middle guide. The impact load of lead roller on middle guide, the curvature of the motion trajectory and angular acceleration of the sliding door centroid were taken as optimization objectives.
2017-03-28
Technical Paper
2017-01-1674
Wenxu NIU, Ke Song, Tong Zhang
Abstract X-in-the-loop (XiL) framework is a validation concept for vehicle product development, which integrates different virtual and physical components to improve the development efficiency. In order to develop and validate an extended validation method based on XiL, Tongji University in Shanghai, China and the Karlsruhe Institute of Technology (KIT) in Karlsruhe, Germany co- performed a feasibility study about an X-in-the-distance-loop demonstration platform. The X-in-the-distance-loop demonstration platform includes a MATLAB/Simulink software platform and geographically distributed equipment (driver simulator, driving electric motor and dynamometer test stand), which are used to conduct bidirectional experiments to test communication of powertrain data between China and Germany.
2017-03-28
Technical Paper
2017-01-1594
Guirong Zhuo, Kun Xiong, Subin Zhang
Abstract Micro electric vehicle has gained increasingly popularity among the public due to its compact size and reasonable price in China in recent years. Since design factors that influence the power of electric vehicle drive-motor like maximum speed, acceleration time and so on are not fixed but varies in certain scopes. Therefore, to optimize the process of matching drive-motor’s power, qualitatively and quantitatively studies should be done to determine the optimal parameter combination and improve the design efficiency. In this paper, three basic operating conditions including driving at top speed, ascending and acceleration are considered in the matching process. And the Sobol’ method of global sensitivity analysis (GSA) is applied to evaluate the importance of design factors to the drive-motor’s power in each working mode.
2017-03-28
Technical Paper
2017-01-1399
Bin Wu, Xichan Zhu, Jianping Shen, Xuejun Cang, Lin li
Abstract A driver steering model for emergency lane change based on the China naturalistic driving data is proposed in this paper. The steering characteristic of three phases is analyzed. Using the steering primitive fitting by Gaussian function, the steering behaviors in collision avoidance and lateral movement phases can be described, and the stabilization steering principle of yaw rate null is found. Based on the steering characteristic, the near and far aim point used in steering phases is analyzed. Using the near and far aim point correction model, a driver steering model for emergency lane change is established. The research results show that the driver emergency steering model proposed in this paper performs well when explaining realistic steering behavior, and this model can be used in developing the ADAS system.
Viewing 1 to 30 of 192

Filter

  • Range:
    to:
  • Year: