Search Results

This paper presents a nonlinear control approach to achieve good performances in vehicle path following and collision avoidance when the vehicle is driving under cruise highway conditions. Nonlinear model predictive control (NLMPC) is adopted to achieve online trajectory control based on a simplified vehicle model. GMRES/Continuation algorithm is used to solve the online optimization problem. Simulations show that the proposed controller is capable of tracking the desired path as well as avoiding the obstacles.

This paper presents a method of utilizing infrared images to quantify the distribution of liquid refrigerant mass flow rate in microchannel heat exchangers, which are widely used in automobile air conditioning systems. In order to achieve quantification, a relationship is built between the liquid mass flow rate through each microchannel tube and the corresponding air side capacity calculated from the infrared measurement of the wall temperature. After being implemented in a heat exchanger model, the quantification method is validated against experimental data. This method can be used for several types of heat exchangers and it can be applied to various heat exchanger designs.

This paper presents results of the visualization of the separation in the vertical header of the automotive condenser. A prototype of a heat exchanger was made that has inlet in the middle of the header, with 21 microchannel tubes as the first pass. In the second header liquid separates and leaves through 4 microchannel tubes beneath while mostly vapor leaves through 11 microchannel tubes on the top as another exit. That way the 2nd pass has liquid below first pass and vapor above it. R134a was used in the tests. Mass flow at the inlet to the header was in the range 8.4 - 30 g/s (mass flux of 54 kg/m2·s-193 kg/m2·s) and quality at the inlet to second header was varied over a range of 0.05 to 0.25, to see their impact on the separation of two-phase flow inside the transparent header. Visualization was performed to better understand and define the physical parameters that dominate the separation phenomena.

In the present study, we developed a reduced chemical reaction mechanism consisted of n-heptane and toluene as surrogate fuel species for diesel engine combustion simulation. The LLNL detailed chemical kinetic mechanism for n-heptane was chosen as the base mechanism. A multi-technique reduction methodology was applied, which included directed relation graph with error propagation and sensitivity analysis (DRGEPSA), non-essential reaction elimination, reaction pathway analysis, sensitivity analysis, and reaction rate adjustment. In a similar fashion, a reduced toluene mechanism was also developed. The reduced n-heptane and toluene mechanisms were then combined to form a diesel surrogate mechanism, which consisted of 158 species and 468 reactions. Extensive validations were conducted for the present mechanism with experimental ignition delay in shock tubes and laminar flame speeds under various pressures, temperatures and equivalence ratios related to engine conditions.

A multi-step acetone-butanol-ethanol (ABE) phenomenological soot model was proposed and implemented into KIVA-3V Release 2 code. Experiments were conducted in an optical constant volume combustion chamber to investigate the combustion and soot emission characteristics under the conditions of 1000 K initial temperature with various oxygen concentrations (21%, 16%, 11%). Multi-dimensional computational fluid dynamics (CFD) simulations were conducted in conjunction under the same operation conditions. The predicted soot mass traces showed good agreement with experimental data. As ambient oxygen decreased from 21% to 11%, ignition delay retarded and the distribution of temperature became more homogenous. Compared to 21% ambient oxygen, the peak value of total soot mass at 16% oxygen concentration was higher due to the suppressed soot oxidation mechanism.

Although refrigerant maldistribution among parallel microchannel tubes is mainly caused by phase separation of vapor and liquid in the header, it is also affected by pressure drop in the header. This study experimentally investigates the pressure drop of single-phase and two-phase R134a flow in the vertical header of a multi-pass microchannel heat exchanger. R134a is circulated into the transparent header through multi-parallel microchannel tubes in the bottom pass and exits through multi-parallel microchannel tubes in the top pass representing the flow in the heat pump mode of a reversible system. The pressure drop in the vertical header causes the top tube has lower mass flow rate than the lower tubes for both single-phase and two-phase flow. The overall pressure drop in the header includes four components: acceleration, gravitation, friction, and minor pressure drop due to microchannel tube protrusion.

Alcohols, especially n-butanol, have received a lot of attention as potential fuels and have shown to be a possible alternative to pure gasoline. The main issue preventing butanol's use in modern engines is its relatively high cost of production. ABE, the intermediate product in the ABE fermentation process for producing bio-butanol, is being studied as an alternative fuel because it not only preserves the advantages of oxygenated fuels, but also lowers the cost of fuel recovery for individual component during fermentation. With the development of advanced ABE fermentation technology, the volumetric percentage of acetone, butanol and ethanol in the bio-solvents can be precisely controlled. In this respect, it is desirable to estimate the performance of different ABE blends to determine the best blend and optimize the production process accordingly.

Butanol has proved to be a very promising alternative fuel in recent years. The production of bio-butanol, typically done using the acetone-butanol-ethanol (ABE) fermentation process is expensive and consumes a lot of energy. Hence it is of interest to study the intermediate fermentation product, i.e. water-containing ABE as a potential fuel. The combustion and emissions performance of ABE29.5W0.5 (29.5 vol.% ABE, 0.5 vol.% water and gasoline blend), ABE30 (30 vol.% ABE and gasoline blend) and ABE0 (pure gasoline) were investigated in this study. The results showed that ABE29.5W0.5 enhanced engine torque by 9.6%-12.7% and brake thermal efficiency (BTE) by 5.2%-11.6% compared to pure gasoline, respectively. ABE29.5W0.5 also showed similar brake specific fuel consumption (BSFC) relative to pure gasoline.

Ethanol is the most widely used renewable fuel in the world now. Compared to ethanol, butanol is another very promising renewable fuel for internal combustion engines. It is less corrosive, and has higher energy density, lower vapor pressure and lower solubility in water. However, the use of Acetone-Butanol-Ethanol (ABE), an intermediate product in ABE fermentation, presents a cost advantage over ethanol and butanol and has attracted much attention recently. In this study, three high-alcohol-content gasoline blends (85% vol. of ethanol, butanol and ABE, referred as E85, B85 and ABE85, respectively) were investigated in a port-injection spark-ignition engine. ABE has a component ratio of 3:6:1. In addition, pure gasoline was also tested as a baseline for comparison. All fuels were tested under the same conditions (1200 RPM, Φ = 0.83−1.25, BMEP = 3 bar).

Recent research has shown that butanol, instead of ethanol, has the potential of introducing a more suitable blend in diesel engines. This is because butanol has properties similar to current transportation fuels in comparison to ethanol. However, the main downside is the high cost of the butanol production process. Acetone-butanol-ethanol (ABE) is an intermediate product of the fermentation process of butanol production. By eliminating the separation and purification processes, using ABE directly in diesel blends has the potential of greatly decreasing the overall cost for fuel production. This could lead to a vast commercial use of ABE-diesel blends on the market. Much research has been done in the past five years concerning spray and combustion processes of both neat ABE and ABE-diesel mixtures. Additionally, different compositions of ABE mixtures had been characterized with a similar experimental approach.