Criteria

Text:
Topic:
Affiliation:
Display:

Results

Viewing 1 to 18 of 18
2006-04-03
Technical Paper
2006-01-0352
Pushkar Vaidya, Xin Wu
This paper introduces a new method to assist deep drawing of tailor-welded blanks with combined restraining force control and binder temperature control. The effect of variable flange temperature and blank holding force on the formability and weld-line displacement of aluminum tailor-welded blank was studied through Finite Element Analysis using LS-DYNA PC.
1998-02-23
Technical Paper
980164
Dinu Taraza, Naeim A. Henein, Walter Bryzik
The local variation of the crankshaft's speed in a multicylinder engine is determined by the resultant gas-pressure torque and the torsional deformation of the crankshaft. Under steady-state operation, the crankshaft's speed has a quasi-periodic variation and its harmonic components may be obtained by a Discrete Fourier Transform (DFT). Based on a lumped-mass model of the shafting, correlations are established between the harmonic components of the speed variation and the corresponding components of the engine torque. These correlations are used to calculate the gas-pressure torque or the indicated mean effective pressure (IMEP) from measurements of the crankshaft's speed.
1997-02-24
Technical Paper
970462
Haryani Permana, David N. Belton, Kenneth M. Rahmoeller, Steven J. Schmieg, Carla E. Hori, Alan Brenner, K.Y.S. Ng
We have prepared and tested laboratory scale monoliths wash-coated with 10, 20 and 30 wt% of either CeO2 or Ce.75Zr.25O2 (remainder is alumina). Wet impregnation was used to load the wash-coated monoliths with 50g/ft Pt:Rh at a 5:1 ratio. The catalyst were aged at temperatures between 825°C and 950°C using a cycled redox aging. The catalysts were then tested in a full-feed simulated exhaust laboratory reactor with air-to-fuel ratio (A/F) perturbations (frequencies at 1 and 3 Hz and amplitudes up to +/- 0.8 A/F). Even the lowest loading of Ce.75Zr.25O2 outperformed all three loadings of CeO2 over a full range of reaction temperatures, A/F perturbations, and catalyst space velocity (SV). Our data indicates that the ceria-zirconia catalysts can tolerate cycled redox aging at sustained bed temperatures at least 25°C higher (∼925°C vs. < 900°C) than can ceria. For the CeO2 catalysts aged at or above 900°C we observed an inverse correlation of catalyst activity to CeO2 loading.
1998-09-29
Technical Paper
982290
Yi Liu, Ming-Chia Lai, Kyoung-Su Im, Nasy Sankagiri, Thomas Loch, Hossein Nivi
A better understanding is needed of the electrostatic rotating bell (ESRB) application of metallic basecoat paint to automobile exteriors in order to exploit their high transfer efficiency without compromising the coating quality. This paper presents the initial results from experimental investigation of sprays from an ESRB which is designed to apply water-borne paint. Water was used as paint surrogate for simplicity. The atomization and transport regions of the spray were investigated using laser light sheet visualizations and phase Doppler particle analyzer (PDPA). The experiments were conducted at varying levels of the three important operating parameters: liquid flow rate, shaping-air flow rate, and bellcup rotational speed. The results show that bellcup speed dominates atomization, but liquid and shaping-air flow rate settings significantly influence the spray structure. The visualization images showed that the atomization occurs in ligament breakup regime.
2008-10-06
Journal Article
2008-01-2424
A. Matsumoto, X. Xie, Ming-Chia Lai, R. E. Winsor, T. C. Huynh
Double-hole nozzle and multiple injections have the potential for better fuel atomization and mixing in DI engine. In order to evaluate the behavior of the spray for the double-hole nozzles against traditional single-hole ones, high-speed spray visualization was carried out using a streak film camera and a copper vapor laser, and in combination with a long-distance camera when taking microscopic movies. The spray penetration and the cone angle were measured based on the images and compared for variable injection pressures, and for single and split injections, under ambient and elevated chamber pressure conditions. The results showed that the spray of the double-hole nozzle has comparable penetration but smaller cone angle when viewed from the nozzle end, compared to the single-hole nozzle with the same total hole discharge cross-sectional area. For microscopic view, it was observed that the interaction between the dual sprays is very dynamic.
2016-04-05
Technical Paper
2016-01-0395
Anindya Deb, Clifford C. Chou, Gunti R. Srinivas, Sanketh Gowda, Goutham Kurnool
Abstract An attractive strategy for joining metallic as well as non-metallic substrates through adhesive bonding. This technique of joining also offers the functionality for joining dissimilar materials. However, doubts are often expressed on the ability of such joints to perform on par with other mechanical fastening methodologies such as welding, riveting, etc. In the current study, adhesively-bonded single lap shear (SLS), double lap shear (DLS) and T-peel joints are studied initially under quasi-static loading using substrates made of a grade of mild steel and an epoxy-based adhesive of a renowned make (Huntsman). Additionally, single lap shear joints comprised of a single spot weld are tested under quasi-static loading. The shear strengths of adhesively-bonded SLS joints and spot-welded SLS joints are found to be similar.
1969-02-01
Technical Paper
690485
L. M. Patrick, K. R. Trosien, F. T. DuPont
Safety performance of an experimental windshield with a thin, chemically tempered inner pane is compared with the standard windshield and other experimental windshields. The chemically tempered windshield has a penetration velocity of 35 mph compared with 26 mph penetration velocity for the standard windshield and has lower peak head accelerations than other types used in the experiments. The windshield tested produces a bulge on impact, which decelerates the head over a long distance with low accelerations. The bulge or pocket is lined with particles that are less lacerative than the standard annealed glass.
2005-04-11
Technical Paper
2005-01-1391
C. L. Xie, M. Hailat, Z. Abedin, X. Wu, G. Newaz, M. Taya, B. Raju
A composite of an aluminum matrix reinforced by short TiNi shape memory alloy (SMA) fibers was fabricated. The processing and thermomechanical behaviors of the composite TiNi/Al6061 were investigated experimentally and analytically. Optimal hot-pressing conditions of TiNi/Al6061 processing were identified. The shape memory effect (SME) was activated by prestraining the composite at the temperature between Ms and As, followed by heating up to Af. SME on mechanical properties, such as microhardness, yield stresses of the composite, were investigated. A computational model for the strengthening mechanism of the short fiber metal matrix composite was utilized to analyze SME on yield stress of the composite. Yield stress of the composite as a function of prestrain was predicted numerically and verified experimentally.
2017-03-28
Technical Paper
2017-01-1467
Ashok Mache, Anindya Deb, Clifford Chou
Abstract There has been a keen interest in recent times on implementation of lightweight materials in vehicles to bring down the unladen weight of a vehicle for enhancing fuel efficiency. Fiber-reinforced composites comprise a class of such materials. As sustainability is also a preoccupation of current product development engineers including vehicle designers, bio-composites based on natural fibers are receiving a special attention. Keeping these motivations of lower effective density, environment friendliness and occupational safety in mind, woven jute fabric based composites have been recently studied as potential alternatives to glass fiber composites for structural applications in automobiles. In the past, mechanical characterization of jute-polyester composites were restricted to obtaining their stress-strain behaviors under quasi-static conditions.
2017-03-28
Technical Paper
2017-01-1461
Sanketh Gowda, Anindya Deb, Goutham Kurnool, Clifford Chou
Abstract Adhesively bonded steel hat section components have been experimentally studied in the past as a potential alternative to traditional hat section components with spot-welded flanges. One of the concerns with such components has been their performance under axial impact loading as adhesive is far more brittle as compared to a spot weld. However, recent drop-weight impact tests have shown that the energy absorption capabilities of adhesively bonded steel hat sections are competitive with respect to geometrically similar spot-welded specimens. Although flange separation may take place in the case of a specimen employing a rubber toughened epoxy adhesive, the failure would have taken place post progressive buckling and absorption of impact energy.
2017-03-28
Technical Paper
2017-01-0358
G Song
Abstract During the extensive testing under NATO and Commercial Standards, crack is observed in camshaft housing to initiate from the eccentric shaft bore and go toward the hold down bolt hole. Hence lab test proposal is originated to induce similar failure in a controlled method and then to compare new design alternatives. CAE analysis follows the same set up as the lab test to duplicate failure mode in stress analysis and fatigue analysis with duty cycle loads, and then figures out two strategies on how to improve the design, including geometry change and material change. In geometry wise, four new design iterations are evaluated for comparison. In material wise, one new material for camshaft housing and five manufacturing effect parameters for pin and rocker arm are compared, including ground, machined, machined and decarburization, casting, as well as casting and nitride.
2017-03-28
Technical Paper
2017-01-0286
Amrinder Singh, Abhishek Ramakrishnan, Guru Dinda
Abstract Additive manufacturing (AM) of metals is finding numerous applications in automotive industry. In 21st century, aluminum is second to steel in automotive sector, because of its high strength to weight ratio. Hence developing AM for aluminum alloys become necessary to make sure industry gains maximum benefit from AM. This study specifically deals with the manufacturing of Al 7050 alloy, which is quite hardest alloy to manufacture using AM. The ultimate goal is to optimize the laser deposition parameters to deposit defect free Al 7050 alloy on rolled aluminum alloy substrate. Parameter optimization (laser power, powder flow rate, and scanning speed) gets difficult with the presence of various low melting and boiling point alloying elements such as Zn, Mg etc. Numerous other challenges faced while depositing Al 7050 alloy, are also briefly discussed in this article.
2015-04-14
Technical Paper
2015-01-1324
Guangtian Gavin Song, Chin-An Tan
Abstract Nowadays, as an irreplaceable means alongside CAD and testing, CAE is more and more widely applied with advanced material modeling and simulation methods continuously being explored, so as to get more accurate result as testing. In vehicle product development process, door slam durability evaluation is an important measurement for body closure structure. So far numerous effort has been taken to develop more mature methods to well define door slam simulation in stress and fatigue life analysis. Overall all methods ever being applied can be summarized as two categories, linear stress based method and nonlinear stress based method. The methodologies, such as inertia relief method, direct transient response solution, or local strain approach, can be included in linear stress based method with linear material properties as symbol in CAE model. In local strain approach, contact surface could be defined in the necessary area with consideration for more realistic load transfer.
2015-04-14
Journal Article
2015-01-1482
Bisheshwar Haorongbam, Anindya Deb, Clifford Chou
Abstract Hat-sections, single and double, made of steel are frequently encountered in automotive body structural components. These components play a significant role in terms of impact energy absorption during vehicle crashes thereby protecting occupants of vehicles from severe injury. However, with the need for higher fuel economy and for compliance to stringent emission norms, auto manufacturers are looking for means to continually reduce vehicle body weight either by employing lighter materials like aluminum and fiber-reinforced plastics, or by using higher strength steel with reduced gages, or by combinations of these approaches. Unlike steel hat-sections which have been extensively reported in published literature, the axial crushing behavior of hat-sections made of fiber-reinforced composites may not have been adequately probed.
2015-04-14
Technical Paper
2015-01-1483
Anindya Deb, N Shivakumar, Clifford Chou
Abstract Rigid polyurethane (PU) foam finds wide applications as a lightweight material in impact safety design such as improving occupant safety in vehicle crashes. The two principal reacting compounds for formulating such foam are variants of polyol and isocyanate. In the present study, an alternative mechanical engineering-based approach for determining, with confidence, the desirable ratio of reacting compounds for formulation of a rigid/crushable PU foam for mechanical applications is demonstrated. According to the present approach, PU foam samples are prepared by varying the mixing ratio over a wide range. The desirable mixing ratio is shown to be the one that optimizes key mechanical properties under compression such as total absorbed energy, specific absorbed energy and energy absorption efficiency.
1999-03-01
Technical Paper
1999-01-1220
Ozgen Akalin, Golam M. Newaz, V. Durga, N. Rao
Low cost and solid lubricant containing plasma spray coated cylinder liners have been investigated for their frictional performance under simulated engine conditions. A bench testing system which has high stroke and large contact width has been used to obtain friction data for plasma spray coated cylinder liners. Results are compared with conventional cast-iron samples. Experimental data has been developed as friction coefficient / crank angle degree diagrams. The effects of speed and temperature have been investigated. Plasma spray coated cylinder liners showed lower friction and higher tendency to develop hydrodynamic lubrication compared to conventional cast-iron bores.
2002-03-04
Technical Paper
2002-01-0486
Richard Stanley, Dinu Taraza
A dimensionless relationship that estimates the maximum bearing load of a 4-cylinder 4-stroke in-line engine has been found. This relationship may assist the design engineer in choosing a desired counterweight mass. It has been demonstrated that: 1) the average bearing load increases with engine speed and 2) the maximum bearing load initially decreases with engine speed, reaches a minimum, then increases quickly with engine speed. This minimum refers to a transition speed at which the contribution of the inertia force overcomes the contribution of the maximum pressure force to the maximum bearing load. The transition speed increases with an increase of counterweight mass and is a function of maximum cylinder pressure and the operating parameters of the engine.
1984-10-01
Technical Paper
841658
Gerald W. Nyquist, Frank T. DuPont, Lawrence M. Patrick
A series of rear impact tests of varying severity was performed using a mini pick-up truck with an instrumented Hybrid III dummy at the driver position. Head, neck and chest loads were monitored. The severities of these loads from an injury standpoint were assessed using biomechanically based reference criteria that are particularly suitable for the Hybrid III. The glass Installation performed well as a head restraint. Glass fracture from head impact was achieved only when the glass was predamaged, with surface scratches on the outer (tensile) side. The amazing strength and flexibility of tempered glass and the dramatic reduction in strength caused by small surface scratches are demonstrated.
Viewing 1 to 18 of 18

    Filter

    • Range:
      to:
    • Year: