Search Results

Since the introduction of the EURO 5 emission legislation particulate matter emissions are no longer only a concern in the development of Diesel engine powertrains. In addition to particulate mass (PM) requirements the new European legislation will also foresee the implementation of a particulate number (PN) requirement for all spark ignition (SI) vehicles with the introduction of EURO 6. Measurements with state of the art gasoline engine powered vehicles show that conventional MPFI engines are already below the future proposed limits while gasoline engines with direct injection are above these limits and will require additional development efforts. This paper discusses both fuel system component requirements as well as control strategies in support of reducing particulate emissions. On the component side, mixture formation in regard to evaporation rate and penetration is a key factor.

Hybrid vehicles are characterized by a combination of mechanical, electrical and control components. The complexity of this mechatronic system requires new methods and tools for a successful development of new hybrid vehicle concepts. It is now possible to accomplish certain tasks earlier in the development projects using virtual prototypes of the powertrain components and the vehicle. The process called “frontloading” integrates simulation, optimization and validation in earlier development phases of a vehicle and prevents from having cost intense problems in later development phases. Besides the reduction of emissions and fuel consumption also the subjective impression of the vehicle driveability are main goals for the optimization of hybrid powertrains.

The incorporation of a detailed engine process calculation that takes into account thermal behavior of the engine and exhaust system is essential for a realistic simulation of transient vehicle operation. This is the only possible way to have a precise preliminary calculation of fuel consumption and emissions. Therefore, a comprehensive thermal network of the engine based on the lumped capacity method has been developed. The model allows the computation of component temperatures in steady state operation as well as in transient engine studies, e.g. investigations of engine warm-up. The model is integrated in a co-simulation environment consisting of a detailed vehicle and engine cycle simulation code. The paper describes the procedure of the co-simulation and presents several examples of warm-up simulations.

Due to its high number of free parameters, the new generation of gasoline engines with direct injection require an efficient calibration process to handle the system complexity and to avoid a dramatic increase in calibration costs. This paper presents a concept of specific toolboxes within a standardized and automated calibration environment, supporting the complexity of GDI engines and establishing standard procedures for distributed development. The basic idea is the combination of a new and more efficient online DoE approach with the automatic and adaptive identification of the region of interest in the high dimensional parameter space. This guarantees efficient experimental designs even for highly non-linear systems with often irregularly shaped valid regions. As the main advantage for the calibration engineer, the new approach requires almost no pre-investigations and no specific statistical knowledge.

The reduction of CO₂ emissions represents a major goal of governments worldwide. In developed countries, approximately 20% of the CO₂ emissions originate from transport, one third of this from commercial vehicles. CO₂ emission legislation is in place for passenger cars in a number of major markets. For commercial vehicles such legislation was also already partly published or is under discussion. Furthermore the commercial vehicles market is very cost sensitive. Thus the major share of fuel cost in the total cost of ownership of commercial vehicles was already in the past a major driver for the development of efficient drivetrain solutions. These aspects make the use of new powertrain technologies, specifically hybridization, mandatory for future commercial powertrains. While some technologies offer a greater potential for CO₂ reduction than others, they might not represent the overall optimum with regard to the total cost of ownership.

Particulate matter emissions are no longer only a concern in the development of Diesel engine powertrains. In addition to particulate mass requirements, the new European legislation for Euro 6 includes a proposed particulate number requirement for all vehicles with gasoline direct injection engines. Euro 6b will establish the first requirement in 2014 which will then be significantly reduced with the implementation of Euro 6c in 2017. This might coincide with the introduction of the World Light Duty Testing Procedure vehicle drive cycle test, raising the bar even higher to reach compliance to the particulate number legislative requirements. Several different investigations revealed that the particulate number emission will become very challenging while the limit for particulate mass can already be met with today's applications.

In light of the growing emphasis on CO2 emissions reduction, Delphi has undertaken an internal development program to show the fuel economy benefits of lean, stratified combustion with its outwardly-opening solenoid injector in a vehicle environment. This paper presents the status of this ongoing development activity which is not yet completed. Progress to date includes a logical progression from single- and multi-cylinder dynamometer engines to the vehicle environment. The solenoid-actuated injector used in this development has an outwardly-opening valve group to generate a hollow-cone spray with a stable, well-defined recirculation zone to support spray-guided stratification in the combustion chamber. The engine management system of the development vehicle was modified from series-production configuration by changing the engine control unit to permit function development and calibration.