Search Results

This paper explores the accuracy of a planar, impulse-momentum impact model in representing the dynamics of three vehicle-to-ground impacts that occurred during a SAE J2114 dolly rollover test. The impacts were analyzed, first, using video analysis techniques to obtain the actual velocity conditions, accelerations, impact force components and the energy loss for each of the impacts. Next, these same impacts were analyzed using the known initial velocity conditions and the subject impact model. The equations of this impact model yielded calculated values for the velocity changes and energy loss for each impact. These calculated results were then compared to the actual dynamics data from the video analysis of the impacts to determine the accuracy of the impact model results. For all three vehicle-to-ground impacts considered in this study, the impact model results for the velocity changes and energy loss showed excellent agreement with the video analysis results for these parameters.

This paper explores the dynamics of rollover crashes and examines factors that influence the severity of the roof-to-ground impacts that occur during these crashes. The paper first reports analysis of 12 real-world rollover accidents that were captured on video. Roll rate time histories for the vehicles in these accidents are reported and the characteristics of these curves are analyzed. Next, the paper uses analytical modeling to explore the influence that the trip phase characteristics may have on the severity of roof-to-ground impacts that occur during the roll phase. Finally, the principle of impulse and momentum is used to derive an analytical impact model for examining the mechanics of a roof-to-ground impact. This modeling is used to identify the influence of various impact conditions on the severity of a roof-to-ground impact.

This paper explores the influence of the impact conditions on the dynamics and the severity of rollover crashes. Causal connections are sought between the impact conditions and the crash attributes to which they lead. The paper begins by extending previously presented equations that describe the dynamics of an idealized vehicle-to-ground impact. It then considers the behavior of these equations under a variety of impact conditions that occur during real-world rollovers. Specifically, the equations of this impact model are used to explore the ways in which and the extent to which rollover dynamics and severity are influenced by the following factors: (1) the vehicle's shape and its orientation at impact, (2) its weight, center-of-mass location, and roll moment of inertia, (3) its translational speed, (4) its downward velocity, and (5) its roll velocity. Throughout this discussion, data from real-world and staged rollover crashes is used to give the parameter study an empirical basis.

This paper evaluates the use of PC-Crash simulation software for modeling the dynamics of a dolly rollover crash test. The specific test used for this research utilized a Ford sport utility vehicle and was run in accordance with SAE J2114. Scratches, gouges, tire marks and paint deposited on the test surface by the test vehicle were documented photographically and by digital survey and a diagram containing the layout of these items was created. The authors reviewed the test video to determine which part of the vehicle deposited each of these pieces of evidence. Position and orientation data for the vehicle in the test were then obtained using video analysis techniques. This data was then analyzed to determine the vehicle’s translational and rotational velocities throughout the test. Next, the test was modeled using PC-Crash.

This paper reports a method for analyzing data from a DriveCam unit to determine impact speeds and velocity changes in vehicle-to-vehicle impacts. A DriveCam unit is an aftermarket, in-vehicle, event-triggered video and data recorder. When the unit senses accelerations over a preset threshold, an event is triggered and the unit records video from two camera views, accelerations along three directions, and the vehicle speed with a GPS sensor. In conducting the research reported in this paper, the authors ran four front-to-rear crash tests with two DriveCam equipped vehicles. For each test, the front of the bullet vehicle impacted the rear of the stationary target vehicle. Each of the test vehicles was impacted in the rear twice - once at a speed of around 10 mph and again at a speed around 25 mph. The accuracy of the DriveCam acceleration data was assessed by comparing it to the data from other in-vehicle instrumentation.

This paper examines the use of camera-matching video analysis techniques to quantify the vehicle dynamics and deformation for a dolly rollover test run in accordance with the SAE Recommended Practice J2114. The method presented enables vehicle motion data and deformation measurements to be obtained without the use of the automated target tracking employed by existing motion tracking systems. Since it does not rely on this automated target tracking, the method can be used to analyze video from rollover tests which were not setup in accordance with the requirements of these automated motion tracking systems. The method also provides a straightforward technique for relating the motion of points on the test vehicle to the motion of the vehicle's center-of-mass. This paper, first, describes the specific rollover test that was utilized. Then, the camera-matching method that was used to obtain the vehicle motion data and deformation measurements is described.

PC-Crash is a vehicular accident simulation software that is widely used by the accident reconstruction community. The goal of this article is to review the prior literature that has addressed the capabilities of PC-Crash and its accuracy and reliability for various applications (planar collisions, rollovers, and human motion). In addition, this article aims to add additional analysis of the capabilities of PC-Crash for simulating planar collisions and rollovers. Simulation analysis of five planar collisions originally reported and analyzed by Bailey [2000] are reexamined. For all five of these collisions, simulations were obtained with the actual impact speeds that exhibited excellent visual agreement with the physical evidence. These simulations demonstrate that, for each case, the PC-Crash software had the ability to generate a simulation that matched the actual impact speeds and the known physical evidence.

A simple two-dimensional particle model was previously developed to calculate occupant ejection trajectories in rollover crashes. Model parameters were optimized using data from a dolly rollover test of a 1998 Ford Expedition in which five unbelted anthropomorphic test devices (ATDs) were completely ejected. In the present study, the model was further validated against a dolly rollover test of a 2004 Volvo XC90 in which three unbelted ATDs were completely ejected. The findings from the experimental testing were then compared to two real world rollover crashes with occupant ejections that were captured on video. The crashes were reconstructed by analyzing the video footage and aerial images of the crash sites. In both cases, the model was able to accurately match the observed trajectories of the ejected occupants, and the optimized model parameters were similar to the values obtained from the dolly rollover testing.

The goal of this paper is to advance rollover crash reconstruction techniques beyond the assumption typically made that a rolling vehicle decelerates at a constant rate. The paper presents and applies a planar vehicle-to-ground impact model to explore the manner in which a vehicle’s deceleration rate would be expected to vary over the course of a rollover. Based on this analysis, several possible variable deceleration rate profile shapes are then suggested for rollover crash reconstruction. Then, two rollover crash tests are analyzed to determine the extent to which these suggested variable deceleration rate profiles can be expected to yield accurate reconstructions of the translational and angular velocity histories for actual rollovers. Overall, each of the suggested variable deceleration rate profiles represented a significant improvement over using a constant deceleration rate.