Search Results

For the modern Formula 1 racing car, the degradation in aerodynamic performance when following another car is well documented. The problem can be broken into two parts; firstly the wake flow generated by these vehicles and the subsequent interaction a following car has with this field. Previous research [1, 2 & 3] has focused upon investigating the later without completely characterizing the former. This paper seeks to address this deficiency with initial data from a newly commissioned 30% scale Formula One wind tunnel model built to the 2011 technical regulations. Experimentation was carried out in the Industrial Wind-Tunnel (IWT) at RMIT University. In the absence of a rolling road an elevated ground plane was implemented; the results obtained show good agreement with the limited published material available. Using a high frequency response, four-hole pressure probe the aft body flow was investigated at multiple downstream locations.

Noise and vibration have important influence on customer's perception of vehicle quality. Research and development have been conducted to investigate the vehicle Heating, Ventilation and Air Conditioning (HVAC) noise generation and transmission mechanism. Noise and vibration comparison tests have been completed for the proposed refinement solutions. Testing results are discussed paying special attentions to the air borne noise reduction. One of interior noise major contributors is the HVAC system, as air handling unit of the HVAC system is located behind the vehicle instrument panel within the cabin. Modifications made to internal structural geometry of the system have been conducted to provide insight into the effect of each structural feature on the overall Sound Pressure Level (SPL) and frequency spectrum components.

Vehicle aerodynamic development is normally undertaken in smooth flow wind tunnels. In contrast, the on-road environment is turbulent, with variations in the relative velocity experienced by the moving vehicle caused mainly by the effects of atmospheric turbulence. In this review the turbulence inherent in the atmosphere is considered, following the approach of wind engineers. The variations of atmospheric wind velocity with time, height, terrain and thermal stratification are summarised and discussed. Statistical parameters presented include mean velocity, turbulence intensities, spectra and probability density functions. The resulting fluctuating approach flow (relative velocity) of the moving vehicle is then considered. The effect of the fluctuating velocity field on parameters of interest to vehicle aerodynamicists (such as aerodynamic noise) are made.

This paper is the first of two papers that address the simulation and effects of turbulence on surface vehicle aerodynamics. This, the first paper, focuses on the characteristics of the turbulent flow field encountered by a road vehicle. The natural wind environment is usually unsteady but is almost universally replaced by a smooth flow in both wind tunnel and computational domains. In this paper, the characteristics of turbulence in the relative-velocity co-ordinate system of a moving ground vehicle are reviewed, drawing on work from Wind Engineering experience. Data are provided on typical turbulence levels, probability density functions and velocity spectra to which vehicles are exposed. The focus is on atmospheric turbulence, however the transient flow field from the wakes of other road vehicles and roadside objects are also considered.

This paper summarises the effects of turbulence on the aerodynamics of road vehicles, including effects on forces and aero-acoustics. Data are presented showing that a different design of some vehicles may result when turbulent flow is employed. Methods for generating turbulence, focusing on physical testing in full-size wind tunnels, are discussed. The paper is Part Two of a review of turbulence and road vehicles. Part One (Cooper and Watkins, 2007) summarised the sources and nature of the turbulence experienced by surface vehicles.

Vortices formed around the A-pillar region dictates the pressure distribution on the side panels of a passenger vehicle and also can lead to aerodynamic noise generation. This paper compares the suitability of various turbulence models in simulating the flow behind a vehicle A-pillar region under laboratory operating conditions. Commercial software's (FLUENT and SWIFT) were used to compare the performance of various turbulence models. In FLUENT, a simplified vehicle model with slanted A-pillar geometry was generated using GAMBIT and in SWIFT, the simplified vehicle model was generated using Fame Hybrid. Computational Fluid Dynamics (CFD) simulations were carried out using FLUENT under steady state conditions using various turbulence models (k-, k- Realize, k- RNG, k- and Spalart Allamaras). In SWIFT, k-, A-RSM and HTM2 turbulence models were used for the steady state simulations. Investigations were carried out at velocities of 60, 100 and 140km/h and at 0-degree yaw angle.

In this study, flow measurements were taken in the wake of a 3/10 scale model of a passenger vehicle using a high frequency, four-hole pressure probe (Dynamic Cobra Probe). The purposes of this study were to further the understanding of the wake development of a passenger vehicle in isolation (in order to provide representative input boundary conditions for CFD and EFD simulations of vehicles traveling in traffic) and to also investigate the wake properties under the influence of upstream turbulence (i.e. with a turbulence generator upstream). The results from several downstream planes are presented and include the time-averaged contour plots of turbulence intensity, velocity deficit and vorticity and cross-flow velocity fields. The presence of increased levels of upstream turbulence mostly affected the upper region of the vehicle wake. In this region, the A-pillar vortex was reduced in size and strength, while the C-pillar vortex had increased in both respects.

Green racing technologies are described with a focus on two categories of sustainable racing; solar racing, including an overview of the World Solar Challenge (WSC) held in Australia, and Formula SAE-E (Society of Automotive Engineers-Electric). Both types of cars utilise sustainably generated electricity, the former uses solar arrays integrated into the vehicle body and the latter electricity generated from a renewable energy park and stored onboard in lithium polymer cells. The design considerations of both vehicles are contrasted with a focus on energy usage minimisation. The Aurora team (which has broken many records, including winning the World Solar Challenge across Australia) is used to illustrate the importance of minimizing the power requirements by having a low aerodynamic drag, frontal area, a highly efficient powertrain and low rolling resistance. To illustrate the technology behind FSAE Electric the R10E car from RMIT is described.

A KIA Soul was instrumented to measure the relative velocity (magnitude and yaw angle) at the front of the vehicle and in-cabin sound at a location close to the side glass near the A-pillar vortex impingement. Tests were conducted at a proving ground under a range of conditions from low wind conditions (~3 m/s) to moderate (7-8 m/s) wind speeds. For any given set of atmospheric conditions the velocity and sound data at any given position on the proving ground were noted to be very repeatable, indicating that the local wakes dominated the "turbulent" velocity field. Testing was also conducted in an aeroacoustic wind tunnel in smooth flow and with a number of novel turbulence generating methods. The resulting sounds were analyzed to study the modulation at frequencies likely to result in fluctuation strength type noise.

Two domains of aerodynamic testing of vehicles are identified; one representing typical driving conditions, where the average atmospheric wind is less than about 10 m/s; the other representing driving under extreme wind conditions for safety considerations. The first domain influences fuel consumption and other parameters related to driving comfort (e.g. aerodynamic noise, transient forces and transient moments experienced during general driving), whereas the second needs to be assessed for stability considerations. The purpose of this paper is to document turbulence commonly encountered by vehicles moving at highway speeds under typical driving conditions. In order to document this, data obtained from hot-wire anemometers fitted above a moving vehicle are presented. It was found that longitudinal and lateral turbulence intensities ranged between 2.5% to 5% and 2.0% to 10% respectively.