Search Results

Effects of high injection pressure and converging nozzles on combustion and emissions of a multi-cylinder diesel engine were investigated. The engine uses a common-rail injection system that allows a maximum injection pressure of 200 MPa. Various injection pressures were tested to explore the benefits of high injection pressure in achieving low exhaust emissions in diesel engines. Injectors used in this study include conventional straight-hole nozzles and converging nozzles with a K factor of 3. Parametric studies were performed including variations in injection timings, number of injection pulses and EGR levels. It was found that low temperature combustion can be achieved by using high EGR with 1) late single injection or 2) double injection with an early pilot and a late main injection. Investigations revealed that high injection pressures significantly reduced soot emissions with an increase in NOx emissions under conventional injection timing ranges.

Numerical models were used to study the effects of dimethyl ether (DME) on the operation of a compression-ignition engine fueled with premixed natural gas. The models used multi-dimensional engine CFD coupled with detailed chemical kinetics. Combustion characteristics of various compositions of the natural gas and DME mixture were simulated. Results showed that combustion phasing, nitrogen oxides emissions, and effects of fuel compositions on engine operating limits were well predicted. Chemical kinetics analysis indicated that ignition was achieved by DME oxidation, which, in turn, induced natural gas combustion. It was found that low temperature heat release became more significant as DME concentration increased. For an appropriate amount of DME in the mixture, the stable engine operating range became narrower as natural gas concentration increased. The model also captured the low temperature combustion features of the present engine with low nitrogen oxides emissions.

Particulate matters, nitrogen oxides, and carbon monoxides emissions from large utility generators using diesel/biodiesel blends were measured. Stack measurements were performed on-site in a number of power plants by following the standard procedure of US EPA. The test engines were chosen to represent typical diesel engines used for electricity generation in the state. Tests were performed using the regular diesel fuel (B0), 10%, 20% and 100% biodiesel blends (B10, B20, B100). Test results showed that particulate matters and carbon monoxides decreased significantly as biodiesel content increases, whereas nitrogen oxides increased. Test results are consistent with other studies using mobile engines in the literature. Note that arbitrary changes in fuel or engine operating conditions are prohibited in power generation industry. Results of this study have been used by the state government to allow the use of biodiesel blends in stationary generators.

The simultaneous reduction of particulate matter (PM) and nitrous oxides (NOx) emissions form diesel exhaust is key to current research activities. Although various technologies have been introduced to reduce emissions from diesel engines, the in-cylinder reduction of PM and NOx due to improved combustion mechanisms will continue to be an important field in research and development of modern diesel engines. Furthermore increasing prices and question over the availability of diesel fuel derived from crude oil has introduced a growing interest. Hence it is most likely that future diesel engines will be operated on pure biodiesel and/or blends of biodiesel and crude oil-based diesel. In this study the performance of different biodiesel blends under low temperature combustion conditions (i.e., high exhaust gas recirculation and advanced fuel injection schemes) was investigated.

The present study investigated HCCI combustion in a heavy-duty diesel engine both experimentally and numerically. The engine was equipped with a hollow-cone pressure-swirl injector using gasoline direct injection. Characteristics of HCCI combustion were obtained by very early injection with a heated intake charge. Experimental results showed an increase in NOx emission and a decrease in UHC as the injection timing was retarded. It was also found that optimization can be achieved by controlling the intake temperature together with the start-of-injection timing. The experiments were modeled by using an engine CFD code with detailed chemistry. The CHEMKIN code was implemented into KIVA-3V such that the chemistry and flow solutions were coupled. The model predicted ignition timing, cylinder pressure, and heat release rates reasonably well. The NOx emissions were found to increase as the injection timing was retarded, in agreement with experimental results.

This study considers combustion processes in a heavy-duty diesel engine at various low emissions operating conditions. The start-of-injection timings varied from -20 to 5 ATDC while the EGR levels varied from 6% to 44%. At certain conditions, HCCI-like combustion characteristics were observed under which low emissions could be achieved. The numerical model used is an improved version of KIVA-3V that can simulate spray breakup and mixture autoignition over a wide range of conditions. The ignition and combustion processes were simulated using both detailed and standard (simplified) chemistry models. Model results show that engine combustion and emissions can be predicted reasonably well under the current conditions. The trends of NOx and soot emissions with respect to the injection timings and EGR levels were well captured. However, it was found that the model over-predicted the NOx emissions in certain early injection cases.

Particle Swarm and the Genetic Algorithm were coupled to optimize multiple performance metrics for the combustion of neat biodiesel in a turbocharged, four cylinder, John Deere engine operating under constant partial load. The enhanced algorithm was used with five inputs including EGR, injection pressure, and the timing/distribution of fuel between a pilot and main injection. A merit function was defined and used to minimize five output parameters including CO, NOx, PM, HC and fuel consumption simultaneously. The combination of PSO and GA yielded convergence to a Pareto regime without the need for excessive engine runs. Results along the Pareto front illustrate the tradeoff between NOx and particulate matter seen in the literature.

In this study both double and triple injection strategies were used with fuel pressures up to 300 and 250 MPa, respectively. Tests were conducted at medium load conditions with cooled, high-pressure EGR at a ratio of 40% and higher. A four-cylinder production engine, featuring double turbochargers with one variable geometry turbocharger, was tested. The double injection strategy consisted of a 20% close-coupled pilot injection while the triple injection strategy introduced a post injection consisting of 10% the total cycle fuel. Results of this study do not indicate an advantage to extreme fuel pressure. The increased air entrainment reduces soot while increasing the premixed burn heat release, mean cylinder temperature, and NOx. Compared to the double injection scheme, triple injections achieved much lower soot for the same EGR rate with only a small NOx penalty.

Various mixtures of ammonia (NH₃) and dimethyl ether (DME) were tested in a diesel engine to explore the feasibility of using ammonia as an alternative, non-carbon fuel to mitigate greenhouse gas emissions. The original diesel fuel injection system was replaced with a new system for injecting ammonia-DME mixtures into the cylinder directly. The injection pressure was maintained at approximately 206 bar for various fuel mixtures including 100% DME, 60%DME-40%NH₃, and 40%DME-60%NH₃ (by weight). As ammonia content was increased in the fuel mixture, the injection timing needed to be advanced to ensure successful engine operation. It was found that cycle-to-cycle variation increased significantly when 40%DME-60%NH₃ was used. In the meantime, combustion of 40%DME-60%NH₃ exhibited HCCI characteristics as the injection timing ranged from 90 to 340 before top-dead-center (BTDC). Emissions data show that soot emissions remained extremely low for the fuel mixtures tested.

Combustion in an HSDI diesel engine using different injectors to realize low emissions is modeled using detailed chemical kinetics in this study. Emission characteristics of the engine are investigated using injectors that have different included spray angles, ranging from 50 to 130 degrees. The engine was operated under PCCI conditions featuring early injection times, high EGR levels and high intake temperatures. The Representative Interactive Flamelet (RIF) model was used with the KIVA code for combustion and emission modeling. Modeling results show that spray targeting plays an important role in determining the in-cylinder mixture distributions, which in turn affect the resulting pollutant emissions. High soot emissions are observed for injection conditions that result in locally fuel rich regions due to spray impingement normal to the piston surface.

A computer model that is able to predict the occurrence of knock in spark ignition engines has been developed and implemented into the KIVA-3V code. Three major sub-models were used to simulate the overall process, namely the spark ignition model, combustion model, and end-gas auto-ignition models. The spark ignition and early flame development is modeled by a particle marker technique to locate the flame kernel. The characteristic-time combustion model is applied to simulate the propagation of the regular flame. The autoignition chemistry in the end-gas was modeled by a reduced chemical kinetics mechanism that is based on the Shell model. The present model was validated by simulating the experimental data in three different engines. The spark ignition and the combustion models were first validated by simulating a premixed Caterpillar engine that was converted to run on propane. Computed cylinder pressure agrees well with the experimental data.

An image acquisition-and-processing camera system was developed for in-cylinder diagnostics of a single-cylinder heavy duty diesel engine. The engine was equipped with an electronically-controlled common-rail fuel injection system that allowed both single and split (multiple) injections to be studied. The imaging system uses an endoscope to acquire luminous flame images from the combustion chamber and ensures minimum modification to the engine geometry. The system also includes an optical linkage, an image intensifier, a CID camera, a frame grabber, control circuitry and a computer. Experiments include both single and split injection cases at 90 MPa and 45 MPa injection pressures at 3/4 load and 1600 rev/min with simulated turbocharging. For the single injection at high injection pressure (90 MPa) the results show that the first luminous emissions from the ignition zone occur very close to the injector exit followed by rapid luminous flame spreading.

An integrated numerical model has been developed for diesel engine computations based on the KIVA-II code. The model incorporates a modified RNG k-ε, turbulence model, a ‘wave’ breakup spray model, the Shell ignition model, the laminar-and-turbulent characteristic-time combustion model, a crevice flow model, a spray/wall impingement model that includes rebounding and breaking-up drops, and other improved submodels in the KIVA code. The model was validated and applied to model successfully different types of diesel engines under various operating conditions. These engines include a Caterpillar engine with different injection pressures at different injection timings, a small Tacom engine at different loads, and a Cummins engine modified by Sandia for optical experiments. Good levels of agreement in cylinder pressures and heat release rate data were obtained using the same computer model for all engine cases.

Accelerated computational optimization of a diesel engine calibration was achieved by combining Support Vector Regression models with the Particle Swarm Optimization routine. The framework utilized a full engine simulation as a surrogate for a real engine test with test parameters closely resembling a typical 4.5L diesel engine. Initial tests were run with multi-modal test problems including Rastragin's, Bukin's, Ackely's, and Schubert's functions which informed the ML model tuning hyper-parameters. To improve the performance of the engine the hybrid approach was used to optimize the Fuel Pressure, Injection Timing, Pilot Timing and Fraction, and EGR rate. Nitrogen Oxides, Particulate Matter, and Specific Fuel Consumption are simultaneously reduced. As expected, optimums reflect a late injection strategy with moderately high EGR rates.